THS4271 Evaluation Module

DP83640T evaluation demonstration board

ISL76534EVAL1Z - EVAL BOARD 1, 28LD, X2QFN, ROHS COMPLIANT

The LTC4227 offers ideal diode-OR and Hot Swap? functions for two power rails by controlling external Nchannel MOSFETs. MOSFETs acting as ideal diodes replace two high power Schottky diodes and the associated heat sinks, saving power and board area. A Hot Swap control MOSFET allows a board to be safely inserted and removed from a live backplane by limiting inrush current. The supply output is also protected against short-circuit faults with a fast acting current limit and internal timed circuit breaker.The LTC4227 regulates the forward voltage drop across the MOSFETs to ensure smooth current transfer from one supply to the other without oscillation. The ideal diodes turn on quickly to reduce the load voltage droop during supply switchover. If the input supply fails or is shorted, a fast turn-off minimizes reverse-current transients.The LTC4227 allows turn-on/off control, and reports fault and power good status for the supply. Part Overcurrent Fault Start-Up Delay LTC4227-1 Latch Off 100ms LTC4227-2 Retry 100ms LTC4227-3 Latch Off 1.6ms LTC4227-4 Retry 1.6ms Applications Redundant Power Supplies and Supply Holdup Computer Systems and Servers Telecom Networks

LMV221 Logarithmic Power Detector Evaluation Board

The AD7686 is a 16-bit, charge redistribution, successive approximation, analog-to-digital converter (ADC) that operates from a single 5 V power supply, VDD. It contains a low power, high speed, 16-bit sampling ADC with no missing codes, an internal conversion clock, and a versatile serial interface port. The part also contains a low noise, wide bandwidth, short aperture delay track-and-hold circuit. On the CNV rising edge, the AD7686 samples an analog input IN+ between 0 V to REF with respect to a ground sense IN?. The reference voltage, REF, is applied externally and can be set up to the supply voltage.Power dissipation scales linearly with throughput.The SPI-compatible serial interface also features the ability, using the SDI input, to daisy-chain several ADCs on a single, 3-wire bus or provides an optional busy indicator. This device is compatible with 1.8 V, 2.5 V, 3 V, or 5 V logic, using the separate supply VIO.The AD7686 is housed in a 10-lead MSOP or a 10-lead QFN (LFCSP) with operation specified from ?40?C to +85?C.APPLICATIONS Battery-powered equipment Data acquisitions Instrumentation Medical instruments Process controls

The LT1970A is a ?500mA power op amp with precise externally controlled current limiting. Separate control voltages program the sourcing and sinking current limit sense thresholds with 1% accuracy. Output current may be boosted by adding external power transistors.The circuit operates with single or split power supplies from 5V to 36V total supply voltage. In normal operation, the input stage supplies and the output stage supplies are connected (VCC to V+ and VEE to V?). To reduce power dissipation it is possible to power the output stage (V+, V?) from independent, lower voltage rails. The amplifier is unity-gain stable with a 3.6MHz gain-bandwidth product and slews at 1.6V/?s. The LT1970A can drive capacitive and inductive loads directly.Open-collector status flags signal current limit circuit activation, as well as thermal shutdown of the amplifier. An enable logic input puts the amplifier into a low power, high impedance output state when pulled low. Thermal shutdown and a ?800mA fixed current limit protect the chip under fault conditions.The LT1970A is packaged in a 20-lead TSSOP package with a thermally conductive copper bottom plate to facilitate heat sinking.Applications Automatic Test Equipment Laboratory Power Supplies Motor Drivers Thermoelectric Cooler Driver

8-A Active Bus Termination/DDR Memory DC/DC Converter

DC1273A: Demo Board for LT1938 - 25V, 2.2A, 2.8MHz Step-Down Switching Regulator

Evaluation Board for TPA6133A2 DirectPath™ Headphone Amplifier