The AD5790?is a single 20-bit, voltage out DAC that operates from a bipolar supply up to 33V. Reference buffers are also provided on-chip The AD5790 accepts a positive reference input in the range of 5V to VDD ? 2.5V and a negative reference input in the range of VSS + 2.5v to 0V. The AD5790 offers a relative accuracy of +/-2 LSB's max and operation is guaranteed monotonic with a -1 LSB to +3 LSB's DNL specification.The part uses a versatile 3-wire serial interface that operates at clock rates up to 35 MHz and is compatible with standard SPI?, QSPI?, MICROWIRE?, and DSP interface standards. The part incorporates a power-on reset circuit that ensures the DAC output powers up to 0V and in a known output impedance state and remains in this state until a valid write to the device takes place. The part provides a disable feature that places the output in a defined load state.PRODUCT HIGHLIGHTS 20-bit resolution Wide power supply range of up to ?16.5 V. ?40?C to +125?C operating temperature range. Low 8 nV/?Hz noise. Low ?0.018 ppm/?C gain error temperature coefficient.APPLICATIONS Medical instrumentation Test and measurement Industrial control Scientific and aerospace instrumentation Data acquisition systems Digital gain and offset adjustment Power supply control

The AD57911 is a single 20-bit, unbuffered voltage-output DACthat operates from a bipolar supply of up to 33 V. The AD5791accepts a positive reference input in the range 5 V to VDD ? 2.5 Vand a negative reference input in the range VSS + 2.5 V to 0 V.The AD5791 offers a relative accuracy specification of ?1 LSBmax, and operation is guaranteed monotonic with a ?1 LSBdifferential nonlinearity (DNL) maximum specification.The device uses a versatile 3-wire serial interface that operates atclock rates up to 35 MHz and that is compatible with standardserial peripheral interface (SPI), QSPI?, MICROWIRE?, and DSP interface standards. The device incorporates a power-on reset circuit that ensures the DACoutput powers up to 0 V and in a known output impedance stateand remains in this state until a valid write to the device takesplace. The device provides an output clamp feature that places the outputin a defined load state.Product Highlights 1 ppm Accuracy. Wide Power Supply Range up to ?16.5 V. Operating Temperature Range: ?40?C to +125?C. Low 7.5 nV/?Hz Noise Spectral Density. Low 0.05 ppm/?C Temperature Drift.Applications Medical instrumentation Test and measurement Industrial control High end scientific and aerospace instrumentation1 Protected by U.S. Patent No. 7,884,747. Other patents pending.

The AD5821A is a single, 10-bit digital-to-analog converter (DAC) with output current sinking capability of 120 mA. It features an internal reference and operates from a single 2.7 V to 5.5 V supply. The DAC is controlled via a 2-wire, I2C?-compatible serial interface that operates at clock rates up to 400 kHz.The AD5821A incorporates a power-on reset circuit that ensures the DAC output powers up to 0 V and remains there until a valid write takes place. It has a power-down feature that reduces the current consumption of the device to 1 ?A maximum.The AD5821A is designed for autofocus, image stabilization, and optical zoom applications in camera phones, digital still cameras, and camcorders.The AD5821A is also suitable for many industrial applications, such as controlling temperature, light, and movement without derating over temperatures ranging from ?30?C to +85?C.The I2C 7-bit address for the AD5821A is 0xC.

The AD5930 is a waveform generator with programmable frequency sweep and output burst capability. Utilizing embedded digital processing that allows enhanced frequency control, the device generates synthesized analog or digital frequency-stepped waveforms. Because frequency profiles are preprogrammed, continuous write cycles are eliminated and thereby free up valuable DSP/microcontroller resources. Waveforms start from a known phase and are incremented phase continuously, which allows phase shifts to be easily determined. Consuming only 8 mA, the AD5930 provides a convenient low power solution to waveform generation.The AD5930 can be operated in a variety of modes. In continuous output mode, the device outputs the required frequency for a defined length of time and then steps to the next frequency. The length of time the device outputs a particular frequency is either preprogrammed and the device increments the frequency automatically, or, alternatively, is incremented externally via the CTRL pin. In burst mode, the device outputs its frequency for a length of time and then returns to midscale for a further predefined length of time before stepping to the next frequency. When the MSBOUT pin is enabled, a digital output is generated.To program the device, the user enters the start frequency, the increment step size, the number of increments to be made, and the time interval that the part outputs each frequency. The frequency sweep profile is initiated, started, and executed by toggling the CTRL pin.A number of different sweep profiles are offered. Frequencies can be stepped in triangular-sweep mode, which continuously sweeps up and down through the frequency range. Alternatively, in saw-sweep mode, the frequency is swept up through the frequency range, but returns to the initial frequency before executing the sweep again. In addition, a single frequency or burst can be generated without any sweep.The AD5930 is written to via a 3-wire serial interface, which operates at clock rates up to 40 MHz. The device operates with a power supply from 2.3 V to 5.5 V. Note that AVDD and DVDD are independent of each other and can be operated from different voltages. The AD5930 also has a standby function, which allows sections of the device that are not being used to be powered down.The AD5930 is available in a 20-lead pb-free TSSOP package.Applications Frequency sweeping/radar Network/impedance measurements Incremental frequency stimulus Sensory applications Proximity and motion BFSK Frequency bursting/pulse trains

The AD5940 and AD5941 are high precision, low power analog front ends (AFEs) designed for portable applications that require high precision, electrochemical-based measurement techniques, such as amperometric, voltammetric, or impedance measurements. The AD5940/AD5941 is designed for skin impedance and body impedance measurements, and works with the AD8233 AFE in a complete bioelectric or biopotential measurement system. The AD5940/AD5941 is designed for electrochemical toxic gas sensing.The AD5940/AD5941 consist of two high precision excitation loops and one common measurement channel, which enables a wide capability of measurements of the sensor under test. The first excitation loop consists of an ultra low power, dual-output string, digital-to-analog converter (DAC), and a low power, low noise potentiostat. One output of the DAC controls the noninverting input of the potentiostat, and the other output controls the noninverting input of the transimpedance amplifier (TIA). This low power excitation loop is capable of generating signals from dc to 200 Hz.The second excitation loop consists of a 12-bit DAC, referred to as the high speed DAC. This DAC is capable of generating high frequency excitation signals up to 200 kHz.The AD5940/AD5941 measurement channel features a 16-bit, 800 kSPS, multichannel successive approximation register (SAR) analog-to-digital converter (ADC) with input buffers, a built in antialias filter, and a programmable gain amplifier (PGA). An input multiplexer (mux) in front of the ADC allows the user to select an input channel for measurement. These input channels include multiple external current inputs, external voltage inputs, and internal channels. The internal channels allow diagnostic measurements of the internal supply voltages, die temperature, and reference voltages.The current inputs include two TIAs with programmable gain and load resistors for measuring different sensor types. The first TIA, referred to as the low power TIA, measures low bandwidth signals. The second TIA, referred to as the high speed TIA, measures high bandwidth signals up to 200 kHz.An ultra low leakage, programmable switch matrix connects the sensor to the internal analog excitation and measurement blocks. This matrix provides an interface for connecting external transimpedance amplifier resistors (RTIAs) and calibration resistors. The matrix can also be used to multiplex multiple electronic measurement devices to the same wearable electrodes.A precision 1.82 V and 2.5 V on-chip reference source is available. The internal ADC and DAC circuits use this on-chip reference source to ensure low drift performance for the 1.82 V and 2.5 V peripherals.The AD5940/AD5941 measurement blocks can be controlled via direct register writes through the serial peripheral interface (SPI) interface, or, alternatively, by using a preprogrammable sequencer, which provides autonomous control of the AFE chip. 6 kB of static random access memory (SRAM) is partitioned for a deep data first in, first out (FIFO) and command FIFO. Measurement commands are stored in the command FIFO and measurement results are stored in the data FIFO. A number of FIFO related interrupts are available to indicate when the FIFO is full.A number of general-purpose inputs/outputs (GPIOs) are available and controlled using the AFE sequencer. The AFE sequencer allows cycle accurate control of multiple external sensor devices.The AD5940/AD5941 operate from a 2.8 V to 3.6 V supply and are specified over a temperature range of ?40?C to +85?C. The AD5940 is packaged in a 56-lead, 3.6 mm ? 4.2 mm WLCSP. The AD5941 is packaged in a 48-lead LFCSP.APPLICATIONS Electrochemical measurements Electrochemical gas sensors Potentiostat/amperometric/voltammetry/cyclic voltammetry Bioimpedance applications Skin impedance Body impedance Continuous glucose monitoring Battery impedance

The AD7124-8 is a low power, low noise, completely integratedanalog front end for high precision measurement applications.The device contains a low noise, 24-bit ?-? analog-to-digitalconverter (ADC), and can be configured to have 8 differentialinputs or 15 single-ended or pseudo differential inputs. The onchiplow gain stage ensures that signals of small amplitude canbe interfaced directly to the ADC.One of the major advantages of the AD7124-8 is that it gives theuser the flexibility to employ one of three integrated powermodes. The current consumption, range of output data rates,and rms noise can be tailored with the power mode selected.The device also offers a multitude of filter options, ensuring thatthe user has the highest degree of flexibility.The AD7124-8 can achieve simultaneous 50 Hz and 60 Hzrejection when operating at an output data rate of 25 SPS (singlecycle settling), with rejection in excess of 80 dB achieved at loweroutput data rates.The AD7124-8 establishes the highest degree of signal chainintegration. The device contains a precision, low noise, lowdrift internal band gap reference and accepts an externaldifferential reference, which can be internally buffered. Otherkey integrated features include programmable low drift excitationcurrent sources, burnout currents, and a bias voltage generator,which sets the common-mode voltage of a channel to AVDD/2.The low-side power switch enables the user to power downbridge sensors between conversions, ensuring the absoluteminimal power consumption of the system. The device alsoallows the user the option of operating with either an internalclock or an external clock.The integrated channel sequencer allows several channels to beenabled simultaneously, and the AD7124-8 sequentially convertson each enabled channel, simplifying communication with thedevice. As many as 16 channels can be enabled at any time, achannel being defined as an analog input or a diagnostic suchas a power supply check or a reference check. This uniquefeature allows diagnostics to be interleaved with conversions.The AD7124-8 also supports per channel configuration. Thedevice allows eight configurations or setups. Each configurationconsists of gain, filter type, output data rate, buffering, andreference source. The user can assign any of these setups on achannel by channel basis.The AD7124-8 also has extensive diagnostic functionalityintegrated as part of its comprehensive feature set. Thesediagnostics include a cyclic redundancy check (CRC), signalchain checks, and serial interface checks, which lead to a morerobust solution. These diagnostics reduce the need for externalcomponents to implement diagnostics, resulting in reducedboard space needs, reduced design cycle times, and cost savings.The failure modes effects and diagnostic analysis (FMEDA) of atypical application has shown a safe failure fraction (SFF) greaterthan 90% according to IEC 61508.The device operates with a single analog power supply from 2.7 Vto 3.6 V or a dual 1.8 V power supply. The digital supply has arange of 1.65 V to 3.6 V. It is specified for a temperature rangeof ?40?C to +125?C. The AD7124-8 is housed in a 32-leadLFCSP package.Note that, throughout this data sheet, multifunction pins, suchas DOUT/RDY, are referred to either by the entire pin name orby a single function of the pin, for example, RDY, when onlythat function is relevant.Applications Temperature measurement Pressure measurement Industrial process control Instrumentation Smart transmitters

The AD7124-8 is a low power, low noise, completely integratedanalog front end for high precision measurement applications.The device contains a low noise, 24-bit ?-? analog-to-digitalconverter (ADC), and can be configured to have 8 differentialinputs or 15 single-ended or pseudo differential inputs. The onchiplow gain stage ensures that signals of small amplitude canbe interfaced directly to the ADC.One of the major advantages of the AD7124-8 is that it gives theuser the flexibility to employ one of three integrated powermodes. The current consumption, range of output data rates,and rms noise can be tailored with the power mode selected.The device also offers a multitude of filter options, ensuring thatthe user has the highest degree of flexibility.The AD7124-8 can achieve simultaneous 50 Hz and 60 Hzrejection when operating at an output data rate of 25 SPS (singlecycle settling), with rejection in excess of 80 dB achieved at loweroutput data rates.The AD7124-8 establishes the highest degree of signal chainintegration. The device contains a precision, low noise, lowdrift internal band gap reference and accepts an externaldifferential reference, which can be internally buffered. Otherkey integrated features include programmable low drift excitationcurrent sources, burnout currents, and a bias voltage generator,which sets the common-mode voltage of a channel to AVDD/2.The low-side power switch enables the user to power downbridge sensors between conversions, ensuring the absoluteminimal power consumption of the system. The device alsoallows the user the option of operating with either an internalclock or an external clock.The integrated channel sequencer allows several channels to beenabled simultaneously, and the AD7124-8 sequentially convertson each enabled channel, simplifying communication with thedevice. As many as 16 channels can be enabled at any time, achannel being defined as an analog input or a diagnostic suchas a power supply check or a reference check. This uniquefeature allows diagnostics to be interleaved with conversions.The AD7124-8 also supports per channel configuration. Thedevice allows eight configurations or setups. Each configurationconsists of gain, filter type, output data rate, buffering, andreference source. The user can assign any of these setups on achannel by channel basis.The AD7124-8 also has extensive diagnostic functionalityintegrated as part of its comprehensive feature set. Thesediagnostics include a cyclic redundancy check (CRC), signalchain checks, and serial interface checks, which lead to a morerobust solution. These diagnostics reduce the need for externalcomponents to implement diagnostics, resulting in reducedboard space needs, reduced design cycle times, and cost savings.The failure modes effects and diagnostic analysis (FMEDA) of atypical application has shown a safe failure fraction (SFF) greaterthan 90% according to IEC 61508.The device operates with a single analog power supply from 2.7 Vto 3.6 V or a dual 1.8 V power supply. The digital supply has arange of 1.65 V to 3.6 V. It is specified for a temperature rangeof ?40?C to +125?C. The AD7124-8 is housed in a 32-leadLFCSP package.Note that, throughout this data sheet, multifunction pins, suchas DOUT/RDY, are referred to either by the entire pin name orby a single function of the pin, for example, RDY, when onlythat function is relevant.Applications Temperature measurement Pressure measurement Industrial process control Instrumentation Smart transmitters

The AD7147 CapTouch? controller is designed for use with capacitance sensors implementing functions such as buttons, scroll bars, and wheels. The sensors need only one PCB layer, enabling ultrathin applications.The AD7147 is an integrated CDC with on-chip environmental calibration. The CDC has 13 inputs channeled through a switch matrix to a 16-bit, 250 kHz sigma-delta (?-?) converter. The CDC is capable of sensing changes in the capacitance of the external sensors and uses this information to register a sensor activation. By programming the registers, the user has full control over the CDC setup.High resolution sensors require minor software to run on the host processor.The AD7147 is designed for single electrode capacitance sensors (grounded sensors). There is an active shield output to minimize noise pickup in the sensor.The AD7147 has on-chip calibration logic to compensate for changes in the ambient environment. The calibration sequence is performed automatically and at continuous intervals as long as the sensors are not touched. This ensures that there are no false or non-registering touches on the external sensors due to a changing environment.The AD7147 has an SPI-compatible serial interface, and the AD7147-1 has an I2C?-compatible serial interface. Both parts have an interrupt output, as well as a GPIO. There is a VDRIVE pin to set the voltage level for the serial interface independent of VCC.The AD7147 is available in a 24-lead, 4 mm ? 4 mm LFCSP and operates from a 2.6 V to 3.6 V supply. The operating current consumption in low power mode is typically 26 ?A for 13 sensors.APPLICATIONS Cell phones Personal music and multimedia players Smart handheld devices Television, A/V, and remote controls Gaming consoles Digital still cameras?

The AD7147 CapTouch? controller is designed for use with capacitance sensors implementing functions such as buttons, scroll bars, and wheels. The sensors need only one PCB layer, enabling ultrathin applications.The AD7147 is an integrated CDC with on-chip environmental calibration. The CDC has 13 inputs channeled through a switch matrix to a 16-bit, 250 kHz sigma-delta (?-?) converter. The CDC is capable of sensing changes in the capacitance of the external sensors and uses this information to register a sensor activation. By programming the registers, the user has full control over the CDC setup.High resolution sensors require minor software to run on the host processor.The AD7147 is designed for single electrode capacitance sensors (grounded sensors). There is an active shield output to minimize noise pickup in the sensor.The AD7147 has on-chip calibration logic to compensate for changes in the ambient environment. The calibration sequence is performed automatically and at continuous intervals as long as the sensors are not touched. This ensures that there are no false or non-registering touches on the external sensors due to a changing environment.The AD7147 has an SPI-compatible serial interface, and the AD7147-1 has an I2C?-compatible serial interface. Both parts have an interrupt output, as well as a GPIO. There is a VDRIVE pin to set the voltage level for the serial interface independent of VCC.The AD7147 is available in a 24-lead, 4 mm ? 4 mm LFCSP and operates from a 2.6 V to 3.6 V supply. The operating current consumption in low power mode is typically 26 ?A for 13 sensors.APPLICATIONS Cell phones Personal music and multimedia players Smart handheld devices Television, A/V, and remote controls Gaming consoles Digital still cameras?

The AD7191 is a low noise, complete analog front end for high precision measurement applications. It contains a low noise, 24-bit sigma-delta (?-?) ADC. The on-chip low noise gain stage means that signals of small amplitude can be interfaced directly to the ADC. It contains two differential analog inputs. The part also includes a temperature sensor that can be used for temperature compensation.For ease-of-use, all the features of the AD7191 are controlled by dedicated pins. The on-chip PGA has a gain of 1, 8, 64, or 128, supporting a full-scale differential input of ?5 V, ?625 mV, ?78 mV, or ?39 mV. The output data rate can be programmed to 10 Hz, 50 Hz, 60 Hz, or 120 Hz. Simultaneous 50 Hz and 60 Hz rejection is obtained when the output data rate is set to 10 Hz or 50 Hz; 60 Hz only rejection is obtained when the output data rate is set to 60 Hz. The AD7191 can be operated with the internal clock, or an external clock can be used.The part operates with a power supply of 3 V to 5.25 V. It consumes a current of 4.35 mA. It is available in a 24-lead TSSOP package.ApplicationsWeigh scalesStrain gauge transducersPressure measurementMedical and scientific instrumentation