ADI 47.2 GHz to 48.2 GHz TX/RX Dual Polarization Beamformer

The ADMV4821 is a silicon germanium (SiGe), 24 GHz millimeterwave (mmW) to 29.5 GHz mmW 5G beamformer. The RF IC is highly integrated and contains 16 independent channels with both transmit and receive functionality. The ADMV4821 supports eight horizontal and eight vertical polarized antennas via the independent RFV and RFH inputs/outputs common pins.In transmit mode, both the RFV and RFH input signals are split via two independent 1:8 power splitters and pass through the eight, independent, corresponding transmit channels. In this mode, each channel includes a vector modulator (VM) to control the phase and two digital variable gain amplifiers (DVGAs) to control the amplitude.In receive mode, input signals pass through two sets of eight receive channels (either vertical or horizontal) and are combined via one independent 8:1 combiner connected to the RFV pin and one independent 8:1 combiner connected to the RFH pin. In this mode, each channel includes a VM to control the phase and a DVGA to control the amplitude.The VM provides a full 360? phase adjustment range in either transmit or receive mode. The VM provides six bits of resolution for 5.625? phase steps.In transmit mode, the total DVGA dynamic range adjustment range is 32.4 dB. The DVGAs provide five bits or six bits of resolution, resulting in 1.0 dB or 0.5 dB amplitude steps, respectively.In receive mode, the DVGA allows for 17.1 dB of dynamic range adjustment. The DVGA also provides six bits of resolution, resulting in 0.5 dB amplitude steps. The DVGAs provide a flat phase response across the full gain range.The transmitter channels contain individual power detectors to detect and calibrate the gain for each channel as well as the channel to channel gain mismatch. Directly connect the ADMV4821 RF ports to a patch antenna to create a dual polarization mmW 5G subarray.Users can program the ADMV4821 by using a 3-wire or 4-wire serial port interface (SPI). The integrated on-chip low dropout (LDO) regulator generates the 1.8 V supply for the SPI circuitry to reduce the number of supply domains required. There are various SPI modes to enable fast startup and control during normal operation.Users can either set the amplitude and phase for each channel individually or program multiple channels simultaneously by using the on-chip memory for beamforming. The on-chip memory can store up to 256 beam positions, which can be allocated for either transmitter or receiver mode in any combination. In addition, four address pins allow SPI control of up to 16 devices on the same serial lines. Dedicated horizontal and vertical polarization load pins also synchronize all devices in the same array. There is a horizontal and vertical polarization transmit and receive mode control pins (TRXV and TRXH) for fast switching between transmit and receive mode.The ADMV4821 comes in a compact, thermally enhanced 10 mm ? 10 mm, RoHs compliant land grid array (LGA) package. The ADMV4821 operates over the ?40?C to +95?C case temperature range. This LGA package allows users to heat-sink the ADMV4821 from the top side of the package for the most efficient thermal heatsinking and to allow flexible antenna placement on the opposite side of the printed circuit board (PCB).Throughout the figures in the data sheet, Tx means transmit (or transmitter) and Rx means receive (or receiver).APPLICATIONS5G applicationsBroadband communicationTest and measurementAerospace and defense

The ADN4600 is an asynchronous, nonblocking crosspoint switch with eight differential PECL-/CML-compatible inputs with programmable equalization and eight differential CML outputs with programmable output levels and pre-emphasis or de-emphasis. The operation of this device is optimized for NRZ data at rates up to 4.25 Gbps.The receive inputs provide programmable equalization with nine settings to compensate for up to 30 in. of FR4 and programmable pre-emphasis with seven settings to compensate for up to 30 in. of FR4 at 4.25 Gbps.The ADN4600 nonblocking switch core implements an 8 ? 8 crossbar and supports independent channel switching through the I2C control interface. Every channel implements an asynchronous path supporting NRZ data rates from dc to 4.25 Gbps. Each channel is fully independent of other channels. The ADN4600 has low latency and very low channel-to-channel skew.The main application for the ADN4600 is to support switching on the backplane, line card, or cable interface sides of serial links.The ADN4600 is packaged in a 9 mm ? 9 mm, 64-lead LFCSP package and operates from ?40?C to +85?C.APPLICATIONS 1?, 2?, 4? FibreChannel XAUI Gigabit Ethernet over backplane 10GBase-CX4 InfiniBand? 50 ? cables

Evaluation board for LMP8640HV-H – 100V/V

UCC28070 Evaluation module

TPS7A7002 Low-Dropout (LDO) Linear Regulator Evaluation Module

Evaluation Module for TPS82672 600-mA; High-Efficiency MicroSiP Step-Down Converter

SIMPLE SWITCHER® Power Module 42Vin; High Output Voltage 2A Eval Board

150mA; 100V Wide Vin Step-Down Switching Regulator Evaluation Module

Multi-Display Inductorless LED Driver with 32 Exponential Dimming Steps in micro SMD