The HMC955LC4B is a 1 to 2 Demux designed to support data transmission rates up to 32 Gbps. The demux uses both rising and falling edges of the half-rate clock to sample the data in sequence 01-02 and latches the data on the rising edge into the differential outputs. The demux also has high-speed clock synchronous invert input that allows for scrambling of the data. The HMC955LC4B also features an output level control pin, VR, which allows for loss compensation or for signal level optimization.All differential inputs to the HMC955LC4B are CML and terminated on-chip with 50 Ohms to the positive supply, GND, and may be AC or DC coupled. The differential CML outputs are source terminated to 50 Ohms and may also be AC or DC coupled. Outputs can be connected directly to a 50 Ohm ground-terminated system or drive devices with CML logic input. The HMC955LC4B operates from a single -3.3 V supply and is available in a ceramic ROHS-compliant 4x4 mm SMT package.APPLICATIONSSONET OC-192Broadband Test & Measurement EquipmentFPGA Interfacing Circuitry16 G and 32 G Fiber Channel100 Gbit EthernetADC Encoder

The HMC958LC5 is a 4:1 Selector designed to support data transmission rates of up to 14 Gbps and selector port operation up to 14 GHz. The selector routes the differential inputs to either one or both of the desired outputs upon assertion of the appropriately selected port. The HMC958LC5 also features an output level control pin, VR, which allows for loss compensation or for signal level optimization.All single-ended input signals to the HMC958LC5 are terminated with 50 ??to ground on-chip, and may be either AC or DC coupled. The outputs of the HMC958LC5 may be operated either differentially or single ended. Outputs can be connected directly to a 50 ??terminated system, while DC blocking capacitors may be used if the terminating system is 50 ? to a non-ground DC voltage. The HMC958LC5 operates from a single -3.3V DC supply and is available in a ceramic RoHS compliant 5 ? 5 mm SMT package.APPLICATIONS SONET OC-192 and 10 GbE 16G Fiber Channel 4:1 Multiplexer Built-In Test Broadband Test & Measurement

The HMC996LP4E is a GaAs PHEMT MMIC analog variable gain amplifier and / or driver amplifier which operates between 5 and 12 GHz. Ideal for microwave radio applications, the amplifier provides up to 18.5 dB of gain, output P1dB of up to +23 dBm, and up to +34 dBm of output IP3 at maximum gain, while requiring only 170 mA from a +5V supply. Gain control voltage pin (Vctrl) is provided to allow variable gain control up to 22 dB. Gain flatness is excellent making the HMC996LP4E ideal for EW, ECM and radar applications. The HMC996LP4E is housed in a RoHS compliant 4 x 4 mm QFN leadless package and is compatible with high volume surface mount manufacturing.Applications Point-to-Point Radio Point-to-Multi-Point Radio EW & ECM Subsystems? X-Band Radar Test Equipment & Sensors

The HMC7150 is a broadband driver amplifier for electro-absorption modulated lasers (EML) and supports data-rates up to 28.3Gbps to meet the 100Gb Ethernet system requirements. The part provides the module designers scalable power dissipation for varying drive voltage characteristics of different modulators and the power consumption of the module can be set as low as 0.12W to 0.5W at 1.5VP-P and 2.3VP-P outputs amplitudes, respectively. The HMC7150 supports wide range of supply voltages from 3.3V to 6V and delivering excellent time domain performance. The output amplitude and cross-point can be adjusted via control pins. The input and output are 50 Ohms matched and used AC coupled. The HMC7150 is in compact leadless 3x3mm surface mountable package.APPLICATIONS 100Gb Ethernet ER4/ LR4 systems CFP/CFP2/CFP4 or similar form factor modules Optical transceivers and pluggable modules Broadband gain stages and pre-amplifiers Broadband Test & Measurement Equipment

The ADG5412/ADG5413 contain four independent single-pole/single-throw (SPST) switches. The ADG5412 switches turn onwith Logic 1. The ADG5413 has two switches with digital controllogic similar to that of the ADG5412; however, the logic is invertedon the other two switches. Each switch conducts equally well inboth directions when on, and each switch has an input signalrange that extends to the supplies. In the off condition, signallevels up to the supplies are blocked.The ADG5412 and ADG5413 do not have a VL pin. The digitalinputs are compatible with 3 V logic inputs over the full operatingsupply range.The on-resistance profile is very flat over the full analog inputrange, which ensures good linearity and low distortion whenswitching audio signals. High switching speed also makes thedevices suitable for video signal switching. The ADG5413exhibits break-before-make switching action for use inmultiplexer applications. Product Highlights Trench isolation guards against latch-up. A dielectric trench separates the P and N channel transistors thereby preventing latch-up even under severe overvoltage conditions. Low RON. Dual-supply operation. For applications where the analog signal is bipolar, the ADG5412/ADG5413 can be operated from dual supplies up to ?22 V. Single-supply operation. For applications where the analog signal is unipolar, the ADG5412/ADG5413 can be operated from a single rail power supply up to 40 V. 3 V logic compatible digital inputs: VINH = 2.0 V, VINL = 0.8 V. No VL logic power supply required. Applications Relay replacement Automatic test equipment Data acquisition Instrumentation Avionics Audio and video switching Communication systems

The AD1030 is an analog front end (AFE) that includes a high precision analog-to-digital converter (ADC), voltage output digital-to-analog converters (VDACs), current output digital-to-analog converters (IDACs), thermoelectric cooler (TEC) controller, and analog comparators.The ADC signal chain contains two analog comparator channels, 10 external voltage inputs, VDAC voltage and current monitor channels, IDAC voltage and current monitor channels, a precharge buffer, and a 1 MSPS successive approximation register (SAR) ADC.The AD1030 provides four IDAC channels. These are low noise, low drift current sources with programmable full-scale output ranges (50 mA, 100 mA, or 150 mA). Each IDAC channel has 12-bit resolution.There are 9?, 12-bit VDAC outputs. Four of these VDACs (Channel 0 to Channel 3) support either a positive voltage range of 0 V to 2.5 V or a negative range from 0 V to ?2.5 V. These ranges can be extended to 0 V to AVDD and 0 V to AVDDNEG.Channel 4 to Channel 7 of the VDACs support a positive voltage range of 0 V to 2.5 V. VDAC Channel 8 supports a positive voltage range of 0 V to 2.5 V. Optionally, Channel 4 to Channel 7 of the VDACs can support an output range of 0 V to AVDD.The AD1030 also integrates a TEC controller with a heating and cooling current up to 1.3 A, is over 90% efficient, and supports a soft start function.Use the 4-wire serial port interface (SPI) for up to 40 MHz or the 2-wire I2C interface for up 1 MHz to configure each functional block and to collect the ADC data.APPLICATIONS Optical networking?100G/200G/400G or higher speed optical modulesFor more information on the AD1030, contact InfoOpticalNetwork@analog.com.

The AD4110-1 is a complete, single-channel, universal input analog-to-digital front end for industrial process control systems where sensor type flexibility is required.The high voltage input is fully software configurable for current or voltage signals and allows direct interface to all standard industrial analog signal sources such as ?20 mA, ?4 mA to ?20 mA, ?10 V, and all thermocouple types. Field power can be supplied for loop powered current output sensors. A range of excitation current sources for resistance temperature detector (RTD) sensors and other resistive sensors are included. The integrated, fully differential programmable gain amplifier (PGA) offers 16 gain settings from 0.2 to 24.The high voltage input can be programmed to power up in either voltage mode or current mode. When programmed to current mode, the unique input circuit architecture provides a path for the loop current, even in the absence of the system module power supply.The AD4110-1 provides internal, front-end diagnostic functions to indicate overvoltage, undervoltage, open wire, overcurrent, and overtemperature conditions. The high voltage input is thermally protected, overcurrent limited, and overvoltage protected.The AD4110-1 incorporates a precision 24-bit, ?-?, analog-todigital converter (ADC) offering conversion rates from 5 SPS to 125 kSPS with simultaneous 50 Hz and 60 Hz noise rejection. Applications Process control and industrial automationRemote and distributed control systemsInstrumentation and measurementSensor and data acquisition

The AD7747 is a high-resolution, ?-? capacitance-to-digital converter (CDC). The capacitance to be measured is connected directly to the device inputs. The architecture features inherent high resolution (24-bit no missing codes, up to 19.5-bit effective resolution), high linearity (?0.01%), and high accuracy (?10 fF factory calibrated). The AD7747 capacitance input range is ?8 pF (changing), and it can accept up to 17 pF common-mode capacitance (not changing), which can be balanced by a programmable on-chip digital-to-capacitance converter (CAPDAC).The AD7747 is designed for single-ended or differential capacitive sensors with one plate connected to ground. For floating (not grounded) capacitive sensors, the AD7745 or AD7746 are recommended.The part has an on-chip temperature sensor with a resolution of 0.1?C and accuracy of ?2?C. The on-chip voltage reference and the on-chip clock generator eliminate the need for any external components in capacitive sensor applications. The part has a standard voltage input that, together with the differential reference input, allows easy interface to an external temperature sensor, such as an RTD, thermistor, or diode.The AD7747 has a 2-wire, I2C-compatible serial interface. The part can operate with a single power supply of 2.7 V to 5.25 V. It is specified over the automotive temperature range of ?40?C to +125?C and is housed in a 16-lead TSSOP package.ApplicationsAutomotive, industrial, and medical systems for:Pressure measurementPosition sensingProximity sensingLevel sensingFlowmetersImpurity detections

The AD7765 is a high performance, 24-bit sigma-delta (?-?) analog-to-digital converter (ADC). It combines wide input bandwidth, high speed, and performance of 112 dB dynamic range at a 156 kHz output data rate. With excellent dc specifications, the converter is ideal for high speed data acquisition of ac signals where dc data is also required.Using the AD7765 eases front-end antialias filtering requirements, simplifying the design process significantly. The AD7765 offers pin-selectable decimation rates of 128? and 256?. Other features include an integrated buffer to drive the reference, as well as a fully differential amplifier to buffer and level shift the input to the modulator.An overrange alert pin indicates when an input signal exceeds the acceptable range. The addition of internal gain and internal overrange registers makes the AD7765 a compact, highly integrated data acquisition device requiring minimal peripheral components.The AD7765 also offers a low power mode, significantly reducing power dissipation without reducing the output data rate or available input bandwidth.The differential input is sampled at up to 40 MSPS by an analog modulator. The modulator output is processed by a series of low-pass filters. The external clock frequency applied to the AD7765 determines the sample rate, filter corner frequencies, and output word rate.The AD7765 device boasts a full band on-board FIR filter. The full stop-band attenuation of the filter is achieved at the Nyquist frequency. This feature offers increased protection from signals that lie above the Nyquist frequency being aliased back into the input signal bandwidth.The reference voltage supplied to the AD7765 determines the input range. With a 4 V reference, the analog input range is ?3.2768 V differential, biased around a common mode of 2.048 V. This common-mode biasing is achieved using the on-chip differential amplifier, further reducing the external signal conditioning requirements.The AD7765 is available in a 28-lead TSSOP package and is specified over the industrial temperature range of ?40?C to +85?C.APPLICATIONS Data acquisition systems Vibration analysis Instrumentation

The AD7770 is an 8-channel, simultaneous sampling ADC. Eightfull sigma-delta (?-?) ADCs are on chip. The AD7770 providesa low input current to allow direct sensor connection. Each inputchannel has a programmable gain stage allowing gains of 1, 2, 4,and 8 to map lower amplitude sensor outputs into the full-scaleADC input range, maximizing the dynamic range of the signalchain. The AD7770 accepts a VREF voltage from 1 V up to 3.6 V.The analog inputs accept unipolar (0 V to VREF) or true bipolar(?VREF/2) analog input signals with 3.3 V or ?1.65 V analogsupply voltages, respectively for PGAGAIN = 1. The analog inputscan be configured to accept true differential, pseudo differential,or single-ended signals to match different sensor outputconfigurations.Each channel contains a PGA, an ADC modulator and asinc3, low latency digital filter. An SRC is provided to allow fineresolution control over the AD7770 ODR. This control can beused in applications where the ODR resolution is required tomaintain coherency with 0.01 Hz changes in the line frequency.The SRC is programmable through the serial port interface (SPI).The AD7770 implements two different interfaces: a data outputinterface and SPI control interface. The ADC data output interfaceis dedicated to transmitting the ADC conversion results fromthe AD7770 to the processor. The SPI writes to and reads fromthe AD7770 configuration registers and for the control andreading of data from the SAR ADC. The SPI can also beconfigured to output the ?-? conversion data.The AD7770 includes a 12-bit SAR ADC. This ADC can beused for AD7770 diagnostics without having to decommissionone of the ?-? ADC channels dedicated to system measurementfunctions. With the use of an external multiplexer, which can becontrolled through the three general-purpose input/output pins(GPIOs), and signal conditioning, the SAR ADC can validatethe ?-? ADC measurements in applications where functionalsafety is required. In addition, the AD7770 SAR ADC includesan internal multiplexer to sense internal nodes.The AD7770 contains a 2.5 V reference and reference buffer. Thereference has a typical temperature coefficient of 10 ppm/?C.The AD7770 offers two modes of operation: high resolution modeand low power mode. High resolution mode provides a higherdynamic range while consuming 10.75 mW per channel; lowpower mode consumes just 3.37 mW per channel at a reduceddynamic range specification.The specified operating temperature range is ?40?C to +105?C,although the device is operational up to +125?C.Applications Protection relays General-purpose data acquisition Industrial process control