The AD1030 is an analog front end (AFE) that includes a high precision analog-to-digital converter (ADC), voltage output digital-to-analog converters (VDACs), current output digital-to-analog converters (IDACs), thermoelectric cooler (TEC) controller, and analog comparators.The ADC signal chain contains two analog comparator channels, 10 external voltage inputs, VDAC voltage and current monitor channels, IDAC voltage and current monitor channels, a precharge buffer, and a 1 MSPS successive approximation register (SAR) ADC.The AD1030 provides four IDAC channels. These are low noise, low drift current sources with programmable full-scale output ranges (50 mA, 100 mA, or 150 mA). Each IDAC channel has 12-bit resolution.There are 9?, 12-bit VDAC outputs. Four of these VDACs (Channel 0 to Channel 3) support either a positive voltage range of 0 V to 2.5 V or a negative range from 0 V to ?2.5 V. These ranges can be extended to 0 V to AVDD and 0 V to AVDDNEG.Channel 4 to Channel 7 of the VDACs support a positive voltage range of 0 V to 2.5 V. VDAC Channel 8 supports a positive voltage range of 0 V to 2.5 V. Optionally, Channel 4 to Channel 7 of the VDACs can support an output range of 0 V to AVDD.The AD1030 also integrates a TEC controller with a heating and cooling current up to 1.3 A, is over 90% efficient, and supports a soft start function.Use the 4-wire serial port interface (SPI) for up to 40 MHz or the 2-wire I2C interface for up 1 MHz to configure each functional block and to collect the ADC data.APPLICATIONS Optical networking?100G/200G/400G or higher speed optical modulesFor more information on the AD1030, contact InfoOpticalNetwork@analog.com.

The AD4110-1 is a complete, single-channel, universal input analog-to-digital front end for industrial process control systems where sensor type flexibility is required.The high voltage input is fully software configurable for current or voltage signals and allows direct interface to all standard industrial analog signal sources such as ?20 mA, ?4 mA to ?20 mA, ?10 V, and all thermocouple types. Field power can be supplied for loop powered current output sensors. A range of excitation current sources for resistance temperature detector (RTD) sensors and other resistive sensors are included. The integrated, fully differential programmable gain amplifier (PGA) offers 16 gain settings from 0.2 to 24.The high voltage input can be programmed to power up in either voltage mode or current mode. When programmed to current mode, the unique input circuit architecture provides a path for the loop current, even in the absence of the system module power supply.The AD4110-1 provides internal, front-end diagnostic functions to indicate overvoltage, undervoltage, open wire, overcurrent, and overtemperature conditions. The high voltage input is thermally protected, overcurrent limited, and overvoltage protected.The AD4110-1 incorporates a precision 24-bit, ?-?, analog-todigital converter (ADC) offering conversion rates from 5 SPS to 125 kSPS with simultaneous 50 Hz and 60 Hz noise rejection. Applications Process control and industrial automationRemote and distributed control systemsInstrumentation and measurementSensor and data acquisition

DC2027A-B: Demo Board for the LTC4364 Surge Stopper with Ideal Diode.

The LTC4162-S is an advanced monolithic synchronous step-down switching battery charger and PowerPath? manager that seamlessly manages power distribution between input sources such as wall adapters, backplanes, solar panels, etc., and a lead-acid battery.A high resolution measurement system provides extensive telemetry information for circuit voltages, currents, battery resistance and temperature which can all be read back over the I2C port. The I2C port can also be used to configure many charging parameters including charging voltages and currents, termination algorithms and numerous system status alerts.The LTC4162-S can charge 6V, 12V, 18V and 24V lead-acid batteries with as much as 3.2A of charge current.The power path topology decouples the output voltage from the battery allowing a portable product to start up instantly under very low battery voltage conditions.The LTC4162-S is available in a thermally enhanced 28-pin 4mm ? 5mm ? 0.75mm QFN surface mount package.Applications Medical Instruments USB-C Power Delivery Industrial Handhelds Ruggedized Notebook Tablet Computers

The LTC3118 is a dual-input, wide voltage range synchronous buck-boost DC/DC converter with an intelligent, integrated, low loss PowerPath control. The unique power switch architecture provides efficient operation from either input source to a programmable output voltage above, below or equal to the input. Voltage capability of up to 18V provides flexibility and voltage margin for a wide variety of applications and power sources.The LTC3118 uses a low noise, current mode architecture with a fixed 1.2MHz PWM mode frequency that minimizes the solution footprint. For high efficiency at light loads, automatic Burst Mode operation can be selected consuming only 50?A of quiescent current in sleep.System level features include ideal diode or VIN priority modes, VIN and VOUT power good indicators, accurate RUN comparators to program independent UVLO thresholds, and output disconnect in shutdown. Other features include 2?A shutdown current, short-circuit protection, soft-start, current limit and thermal overload protection.The LTC3118 is offered in thermally enhanced 24-lead 4mm ? 5mm QFN and 28-lead TSSOP packages.Applications Systems with Multiple Input Sources Back Up Power Systems Wall Adapter or Li-Ion(s) Input to 5VOUT Battery or Super Capacitor Input for Reserve Power Replace Diode-OR Designs with Higher Efficiency,?Flexibility and Performance

Demonstration circuit 2046A-C is a PoE powered device (PD) with an isolated power supply using synchronous flyback topology, featuring the LT4276 and ideal diode bridge controller (LT4321).

Demonstration circuit 2046A-E is a PoE powered device (PD) with an isolated power supply using synchronous flyback topology, featuring the LT4276 and ideal diode bridge controller (LT4321).

Demonstration Circuit 2048A is a nanopower buckboost DC/DC with energy harvesting battery life extender featuring the LTC3330. The LTC3330 integrates a high voltage energy harvesting power supply plus a DC/DC converter powered by a primary cell battery to create a single output supply for alternative energy applications. The energy harvesting power supply, consisting of an integrated low-loss full-wave bridge with a high voltage buck converter, harvests energy from piezoelectric, solar or magnetic sources. The primary cell input powers a buck-boost converter capable of operating down to 1.8V at its input. Either DC/DC converter can deliver energy to a single output.

The LTM4675 is a dual 9A or single 18A step-down ?Module? (micromodule) DC/DC regulator with 40ms turn-on time. It features remote configurability and telemetry-monitoring of power management parameters over PMBus?an open standard I2C-based digital interface protocol. The LTM4675 is comprised of fast analog control loops, precision mixed-signal circuitry, EEPROM, power MOSFETs, inductors and supporting components.The LTM4675?s 2-wire serial interface allows outputs to be margined, tuned and ramped up and down at programmable slew rates with sequencing delay times. Input and output currents and voltages, output power, temperatures, uptime and peak values are readable. Custom configuration of the EEPROM contents is not required. At start-up, output voltages, switching frequency, and channel phase angle assignments can be set by pin-strapping resistors. The LTpowerPlay? GUI and DC1613 USB-to-PMBus converter and demo kits are available.The LTM4675 is offered in a 16mm ? 11.9mm ? 3.51mm BGA package available with SnPb or RoHS compliant terminal finish.APPLICATIONS System Optimization in Prototype and Production

The LT8710 is a synchronous PWM DC/DC controller with a rail-to-rail output current monitor and control. The LT8710 is ideal for many types of power supply topologies and can be easily configured for boost, SEPIC, inverting, or flyback configurations.The LT8710?s rail-to-rail output current monitor and control allows the part to be configured in current limited applications such as battery charging. The FLAG pin can be used as a power good indication or C/10 indication allowing for accurate bulk and float battery voltages.The LT8710?s switching frequency range can be set between 100kHz and 750kHz using an external resistor or synchronized to an external clock.The LT8710 also features innovative EN/FBIN pin circuitry that allows for slowly varying input signals and an adjustable undervoltage lockout function. The pin is also used for input voltage regulation to avoid collapsing a high impedance input supply. Additional features such as frequency foldback and soft-start are integrated. The LT8710 is available in a 20-lead TSSOP package.Applications High Power Local Power Supply Wide Input Voltage Range SEPIC/Inverting Lead Acid Battery Charger Automotive Engine Control Unit (ECU) Power Solar Panel Power Converter