Demonstration circuit 1812A (Figure 1) features the LTC2943. The LTC2943 has an operating range of 3.6V to 20V making it perfectly suited for multicell battery applications. A precision analog coulomb counter integrates current measured through a sense resistor between the battery’s positive terminal and the load or charger. The default value assembled on the DC1812A-A is 100mΩ for a maximum current measurement of 500mA. The LTC2943 measures voltage, current and temperature with an internal 14-bit No Latency ΔΣ™ ADC. The measurements are stored in internal registers accessible via the onboard SMBus/I2C interface.

The ADGS1412 contains four independent single-pole/single-throw(SPST) switches. A serial peripheral interface (SPI)controls the switches. The SPI interface has robust error detectionfeatures such as cyclic redundancy check (CRC) error detection,invalid read/write address detection, and SCLK count errordetection.It is possible to daisy-chain multiple ADGS1412 devices together.Daisy-chain mode enables the configuration of multiple deviceswith a minimal amount of digital lines. The ADGS1412 can alsooperate in burst mode to decrease the time between SPIcommands.iCMOS construction ensures ultralow power dissipation, makingthe device ideally suited for portable and battery-poweredinstruments.Each switch conducts equally well in both directions when on,and each switch has an input signal range that extends to thesupplies. In the off condition, signal levels up to the suppliesare blocked.The on-resistance profile is flat over the full analog input range,which ensures good linearity and low distortion when switchingaudio signals.Product Highlights SPI interface removes the need for parallel conversion, logic traces and reduces general-purpose input/output (GPIO) channel count. Daisy-chain mode removes additional logic traces when multiple devices are used. CRC error detection, invalid read/write address detection, and SCLK count error detection ensures a robust digital interface. CRC and error detection capabilities allow the use of the ADGS1412 in safety critical systems. Guaranteed break-before-make switching allows the use of the ADGS1412 in multiplexer configurations with external wiring. Minimum distortion.Applications Automated test equipment Data acquisition systems Battery-powered systems Sample-and-hold systems Audio signal routing Video signal routing Communications systems Relay replacement

Demonstration circuit 2161A showcases the LTC4231 Micropower Hot Swap™ Controller in a 12V, 3A application. Included on the board are input overvoltage and reverse voltage protection, input voltage dividers for UV and OV detection, an output voltage LED, jumpers to disable UV/OV, manual and remote enable control, and quiescent current measurement. There are turrets provided to monitor input voltage, output voltage, output status, quiescent current, several ground connections, timer pin, and control the ON pin. Input, output and return voltages are provided on banana jacks.

DC839A: Demo Board for the LTC4413 Dual 2.6A, 2.5V to 5.5V, Ideal Diodes in 3mm × 3mm DFN.

ADS1258 Performance Demonstration Kit

Pressure Sensor Development Tools LPS22HH adapter board for a standard DIL24 socket

The ADuC7128 /?ADuC7129 are fully integrated, 1 MSPS, 12-bit data acquisition systems incorporating a high performance, multi-channel analog-to-digital converter (ADC), DDS with line driver, 16-/32-bit MCU, and Flash/EE memory on a single chip.The ADC consists of up to 14 single-ended inputs. The ADC can operate in single-ended or differential input modes. The ADC input voltage is 0 to VREF. Low drift band gap reference, temperature sensor, and voltage comparator complete the ADC peripheral set.The ADuC7128/ADuC7129 integrate a differential line driver output. This line driver transmits a sine wave whose values are calculated by an on-chip DDS or a voltage output determined by the DACDAT MMR.The devices operate from an on-chip oscillator and PLL, generating an internal high frequency clock of 41.78 MHz. This clock is routed through a programmable clock divider from which the MCU core clock operating frequency is generated.The microcontroller core is an ARM7TDMI?, 16-/32-bit reduced instruction set computer (RISC), offering up to 41 MIPS peak performance. There are 126 kB of nonvolatile Flash/EE provided on-chip, as well as 8 kB of SRAM. The ARM7TDMI core views all memory and registers as a single linear array.On-chip factory firmware supports in-circuit serial download via the UART serial interface port, and nonintrusive emulation is also supported via the JTAG interface. These features are incorporated into a low cost QuickStart? development system supporting this MicroConverter? family.The parts operate from 3.0 V to 3.6 V and are specified over an industrial temperature range of ?40?C to +125?C. When operating at 41.78 MHz, the power dissipation is 135 mW. The line driver output, if enabled, consumes an additional 30 mW.

The ADP1853 is a wide range input, dc-to-dc, synchronousbuck controller capable of running from commonly used 3.3 Vto 12 V (up to 20 V) voltage inputs. The device nominallyoperates in current mode with valley current sensing providingthe fastest step response for digital loads. It can also beconfigured as a voltage mode controller with low noise andcrosstalk for sensitive loads.The ADP1853 can be used as a master synchronization clockfor the power system and for convenient synchronizationbetween controllers. The CLKOUT signal can synchronizeother devices in the ADP185x family such that slave devicesare phase-shifted from the master to reduce the input ripplecurrent, improve EMI, and reduce the size of the input bulkcapacitance. The ADP1853 can also be configured as a slavedevice for current sharing. Additionally, the ADP1853 includesaccurate tracking, precision enable, and power good functionsfor sequencing. The ADP1853 provides a high speed, high peakcurrent gate driving capability to enable energy efficient powerconversion. The device can be configured to operate in powersaving mode by skipping pulses, reducing switching losses andimproving efficiency at light load and standby conditions.The accurate current limit allows design within a narrowerrange of tolerances and can reduce overall converter size andcost. The ADP1853 can regulate down to 0.6 V output using ahigh accuracy reference with ?1% tolerance over thetemperature range from ?40?C to 125?C.With a wide range input voltage, the ADP1853 is designed toprovide the designer with maximum flexibility for use in avariety of system configurations; loop compensation, soft start,frequency setting, power saving mode, current limit, andcurrent sense gain can all be programmed using externalcomponents. In addition, the external RAMP resistor allowschoosing optimal slope and VIN feedforward in both currentand voltage mode for excellent line rejection. The linearregulator and the boot strap diode for the high-side driver areinternal.Protection features include undervoltage lock out, overvoltage,overcurrent/short circuit, and overtemperature.Applications Intermediate bus and POL systems requiring sequencing and tracking, including Telecom base station and networking Industrial and Instrumentation Medical and healthcare

The HMC521ALC4 is a compact, gallium arsenide (GaAs), monolithic microwave integrated circuit (MMIC), inphase quadrature (I/Q) mixer in a RoHS compliant, 24-terminal ceramic leadless chip carrier (LCC) package. This device can be used as either an image reject mixer or a single sideband upconverter. The mixer uses two standard, double balanced mixer cells and a 90? hybrid coupler fabricated in a GaAs, metal?semiconductor field effect transistor (MESFET) process. This?device is a smaller alternative to hybrid style image reject?mixers and single sideband upconverter assemblies. The HMC521ALC4 eliminates the need for wire bonding, allowing?use of surface-mount manufacturing techniques.Applications Microwave and very small aperture terminal (VSAT) radios Test equipment Military electronic warfare (EW); electronic countermeasure (ECM); and command, control, communications, and intelligence (C3I)

ADS1672 Performance Demonstration Kit (PDK)