SN65LVDS125 Evaluation Module

AMC1100 Evaluation Module

Step Down Converters | Bypass Mode for Ultralow-Power Wireless; Evaluation Module; TPS62730

LM57 evaluation module

C5517 Evaluation Module (EVM)

MODULE EVAL FOR ADS7867

High Performance; High Fidelity Audio Operational Amplifier

The ADG918/ADG919 are wideband switches using a CMOSprocess to provide high isolation and low insertion loss to1 GHz. The ADG918 is an absorptive (matched) switch having50 ? terminated shunt legs, whereas the ADG919 is a reflectiveswitch. These devices are designed such that the isolation ishigh over the dc to 1 GHz frequency range. They have on-boardCMOS control logic, thus eliminating the need for externalcontrolling circuitry. The control inputs are both CMOS andLVTTL compatible. The low power consumption of theseCMOS devices makes them ideally suited to wireless andgeneral-purpose high frequency switching applications.Product Highlights ?43 dB off isolation at 1 GHz. 0.8 dB insertion loss at 1 GHz. Tiny 8-lead MSOP/LFCSP.Applications Wireless communications General-purpose RF switching Dual-band applications High speed filter selection Digital transceiver front end switch IF switching Tuner modules Antenna diversity switching

The ADGM1304 is a wideband, single-pole, four-throw (SP4T) switch, fabricated using Analog Devices, Inc., microelectro-mechanical system (MEMS) switch technology. This technology enables a small form factor, wide RF bandwidth, highly linear, low insertion loss switch that is operational from 0 Hz/dc to 14 GHz, making the ADGM1304 an ideal solution for a wide range of RF and precision equipment switching needs.An integrated driver chip generates a high voltage to electrostatically actuate a switch that can be controlled by a parallel interface and a serial peripheral interface (SPI). All four switches are independently controllable.The device is packaged in a 24-lead, 5 mm ? 4 mm ? 0.95 mm, lead frame chip-scale package (LFCSP).To ensure optimum operation of the ADGM1304, the Critical Operational Requirements section must be followed exactly.The on resistance (RON) performance of the ADGM1304 is affected by device to device variation, channel to channel variation, cycle actuations, settling time post turn on, bias voltage, and temperature changes.APPLICATIONS Relay replacements Automatic test equipment: RF/high speed digital and mixed signals Load and probe boards: RF/high speed digital and mixed signals RF test instrumentation Reconfigurable filters and attenuators High performance RF switching

The ADGS1212 contains four independent single-pole/single-throw(SPST) switches. A serial peripheral interface (SPI)controls the switches. The SPI interface has robust error detectionfeatures such as cyclic redundancy check (CRC) error detection,invalid read/write address detection, and SCLK count errordetection.It is possible to daisy-chain multiple ADGS1212 devices together.Daisy-chain mode enables the configuration of multiple deviceswith minimal digital lines. The ADGS1212 can also operate inburst mode to decrease the time between SPI commands.iCMOS construction ensures ultralow power dissipation, makingthe device ideal for portable and battery-powered instruments.Each switch conducts equally well in both directions when on,and each switch has an input signal range that extends to thesupplies.In the off condition, signal levels up to the supplies are blocked.The ultralow capacitance and charge injection of these switchesmake them ideal solutions for data acquisition and sample-andholdapplications where low glitch and fast settling are required.Fast switching speed coupled with high signal bandwidth makethe device suitable for video signal switching.Multifunction pin names may be referenced by their relevantfunction only.Product Highlights SPI interface removes the need for parallel conversion, logic traces, and reduces the general-purpose input/output (GPIO) channel count. Daisy-chain mode removes additional logic traces when multiple devices are used. CRC error detection, invalid read/write address detection, and SCLK count error detection ensure a robust digital interface. CRC and error detection capabilities allow the ADGS1212 to be used in safety critical systems. Guaranteed break-before-make switching allows the the ADGS1212 to be used in multiplexer configurations with external wiring. The ADGS1212 1.8 V logic compatibility with 2.7 V ? VL ? 3.3 V Ultralow capacitance. <1 pC charge injection.Applications Automated test equipment Data acquisition systems Battery-powered systems Sample-and-hold systems Audio signal routing Video signal routing Communications systems