The ADMV1550 is a general-purpose, double balanced mixer in a leadless, RoHS compliant, surface-mount technology (SMT) package that can be used as an upconverter or down-converter between 15 GHz and 67 GHz. The wide bandwidth from 0 GHz to 20 GHz on the intermediate frequency (IF) port allows flexible frequency planning to avoid spurious products. This mixer is fabricated in a gallium arsenide (GaAs), monolithic microwave integrated circuit (MMIC) process and requires no external components or matching circuitry. The ADMV1550 provides excellent local oscillator (LO) to radio frequency (RF) and LO to IF suppression due to optimized balun structures. The mixer operates with an LO amplitude above 15 dBm. The RoHS compliant ADMV1550 eliminates the need for wire bonding, allowing the use of surface-mount manufacturing techniques.APPLICATIONSMicrowave and very small aperture terminal (VSAT) radiosTest equipmentMilitary electronic warfare (EW)Electronic countermeasure (ECM)Command, control, communications, and intelligence (C3I)

The ADMV4420 is a highly integrated, double balanced, active mixer with an integrated fractional-N synthesizer, ideally suited for next generation K band satellite communications.The RF front end consists of an integrated RF balun and low noise amplifier (LNA) for an optimal, 7 dB, single-sideband noise figure while minimizing external components. Additionally, the high dynamic range IF output amplifier provides a nominal conversion gain of 36 dB.An integrated low phase noise, fractional-N, phase-locked loop (PLL) with a multicore voltage controlled oscillator (VCO) and internal 2? multiplier generate the necessary on-chip LO signal for the double balanced mixer, eliminating the need for external frequency synthesis. The multicore VCO uses an internal autocalibration routine that allows the PLL to select the necessary settings and lock in approximately 400 ?s.The reference input to the PLL employs a differentially excited 50 MHz crystal oscillator. Alternatively, the reference input can be driven by an external, singled-ended, 50 MHz source. The phase frequency detector (PFD) comparison frequency of the PLL operates up to 50 MHz.The ADMV4420 is fabricated on a silicon germanium (SiGe), bipolar complementary metal-oxide semiconductor (BiCMOS) process, and is available in a 32-lead, RoHS compliant, 5 mm ? 5 mm LFCSP package with an exposed pad. The device is specified over the ?40?C to +85?C temperature range on a 5 V power supply.Applications Satellite communication Point to point microwave communication

The ADMV4828 is a silicon on insulator (SOI), 24.0 GHz to 29.5 GHz, mmW 5G beamformer. The RF integrated circuit (RFIC) is highly integrated and contains 16 independent transmit and receive channels. The ADMV4828 supports eight horizontal and eight vertical polarized antennas via independent RFV and RFH input/outputs.In transmit mode, both the RFV input and RFH input signals feed into separate amplifiers. Each path after the amplifiers splits into eight independent channels via the 1:8 power splitters. In receive mode, input signals pass through either the vertical or horizontal receive channels and combine via two independent 8:1 combiners to the common RFV pin or RFH pin. In either mode, each transmit and receive channel includes a vector modulator (VM) to control the phase, and two digital variable gain amplifiers (DVGAs) to control the amplitude. The VM provides a full 360? phase adjustment range in either transmit or receive mode to provide 6 bits of resolution for 5.625? phase steps. A phase step policy for the transmit and receive VM is provided to ensure optimum phase step performance. The total DVGA dynamic range in transmit mode is 34.5, which provides 6 bits of resolution that results in 0.5 dB amplitude steps and 5 bits of resolution that results in 1 dB amplitude steps. In receive mode, the total dynamic range is 28 dB, which provides 5 bits of resolution that results in 0.5 dB amplitude steps and 5 bits of resolution that results in 1 dB amplitude steps. The DVGAs provide a flat phase response across the full gain range. A gain policy for DVGA1 and DVGA2 is provided in the AN-2074 Application Note, ADMV4828 Application Note to ensure optimized performance across the attenuation range with 0.5 dB step resolution from 0 dB to 34.5 dB attenuation for transmit mode and 0.5 dB step resolution from 0 dB to 28 dB attenuation for receive mode. The transmit channels contain individual transmit power detectors to detect either modulated or continuous wave signals to calibrate for each channel gain as well as channel to channel gain mismatch. Each receive channel contains an RF power overload circuit (receive channel overload detection circuit) to prevent potential damage to the device as a result of blocker instances. The ADMV4828 RF ports can be connected directly to a patch antenna to create a dual polarization mmW 5G subarray.The ADMV4828 can be programmed using a 3-wire or 4-wire serial port interface (SPI). An integrated, on-chip low dropout (LDO) voltage regulator generates the 1.0 V supply for the SPI circuitry to reduce the number of supply domains required. Various SPI modes are available to enable fast startup and control during normal operation. The amplitude and phase for each channel can be set individually or multiple channels can be programmed simultaneously using the on-chip memory for beamforming. The on-chip memory can store up to 2048 beam positions that can be allocated for either transmit mode or receive mode for the horizontal channels and vertical channels. On-chip nonvolatile memory (NVM) is used to store the calibrated gain and phase offset coefficients and the reference values for each individual channel from the factory. These values are used to perform channel to channel or chip to chip calibration. In addition, four address pins (CHIP_ADDx) allow independent SPI control of up to 16 devices on the same serial lines. To control multiple devices via the same serial lines with the same instructions, activate broadcast mode via the external enable pin (BR_EN). Dedicated horizontal and vertical polarization load pins (LOAD_V and LOAD_H) provide the synchronization of all devices in the same array. A horizontal and vertical polarization transmit mode and receive mode control pin (TRX_H or TRX_V) is provided for fast switching between transmit mode and receive mode.The ADMV4828 comes in a compact, 304-ball, 10 mm ? 8.5 mm chip scale package ball grid array (CSP_BGA). The ADMV4828 operates over the ?40?C to +95?C case temperature (TC) range. This CSP_BGA package enables the ability to heatsink the ADMV4828 from the topside of the package for the most efficient thermal heatsinking and to allow flexible antenna placement on the opposite side of the printed circuit board (PCB).APPLICATIONSmmW 5G applicationBroadband communication

The ADMV7420 is a fully integrated system in package (SiP) inphase/quadrature (I/Q) downconverter that operates betweenan intermediate frequency (IF) output range of dc and 2 GHzand a radio frequency (RF) input range of 81 GHz and 86 GHz.The device provides a small signal conversion gain of 10 dBwith 30 dBc of image rejection. The ADMV7420 uses a lownoise amplifier followed by an image rejection mixer that isdriven by a 6? local oscillator (LO) multiplier. Differential I andQ mixer outputs are provided for direct conversion applications.Alternatively, the outputs can be combined using an external90? hybrid and two external 180? hybrids for single-endedapplications.The ADMV7420 comes in a fully integrated, surface-mount,34-terminal, 11 mm ? 13 mm, chip array small outline no leadcavity (LGA_CAV) package. The ADMV7420 operates over the?40?C to +85?C case temperature range. APPLICATIONS E-band communication systems High capacity wireless backhauls Test and measurement Aerospace and defense

The ADMV8432 is a monolithic microwave integrated circuit (MMIC), tunable band-pass filter that features a user selectable pass-band frequency. The 3 dB filter bandwidth is >17% of the center frequency (fCENTER). Additionally, fCENTER can be varied between 16.6 GHz to 30.1 GHz by applying an analog tuning voltage between 0 V to 15 V. The usable pass band corner frequencies (fCORNER) span from 15.1 GHz to 32 GHz. This tunable filter can be used as a much smaller alternative to physically large switched filter banks and cavity tuned filters. This tunable filter has excellent microphonics due to the monolithic design and provides a dynamically adjustable solution in advanced communications applications.APPLICATIONS Test and measurement equipment Military radar and electronic warfare (EW) systems Video satellite (VSAT) communications?

The ADMV9611 is a complete millimeterwave (mmWave) wireless connectivity solution in a small printed circuit assembly (PCA) format. All millimeterwave signals are confined to the printed circuit assembly, simplifying implementation. Wireless transmission is achieved using the integrated circularly polarized (CP) omnidirectional patch antenna array, which enables communication in many applications, including rotation. Following the antenna array is an integrated diplexer that provides isolation between the separate transmit and receive paths on the board, which reduces multipath distortion. The receive path integrates all components to demodulate the 58.0125 GHz frequency to baseband signals. The flexible receiver gain control is programmable over a wide range to easily accommodate the required link budget. The receiver baseband outputs are dc-coupled and can provide over 500 mV of differential output signal level. Likewise, the transmit path integrates all components to modulate input baseband signals to 63 GHz. The transmitter has programmable gain control to maintain level transmit power. The transmit baseband inputs are dc-coupled and have a broad common-mode input range. Synthesizers are integrated to maintain excellent frequency stability vs. temperature. The simple amplitude modulation (AM) scheme eliminates the need for external data converters, allowing for bit rates of greater than 100 Mbps. On-board power management is integrated to a single 5 V voltage rail to power the ADMV9611.Together with the ADMV9621, the ADMV9611 provides a complete, full duplexed 60 GHz data link for high speed data transmission in the unlicensed 60 GHz industrial, scientific, and medical (ISM) band.APPLICATIONS60 GHz short data link for industrial and medical high data rate applicationsHigh speed data for rotating applications, such as slip rings and magnetic resonance imaging systems

The ADP1031 is a high performance, isolated micropowermanagement unit (PMU) that combines an isolated flybackdc-to-dc regulator, an inverting dc-to-dc regulator, and abuck dc-to-dc regulator, providing three isolated power rails.Additionally, the ADP1031 contains four, high speed, serialperipheral interface (SPI) isolation channels and three general-purpose isolators for channel to channel applications where lowpower dissipation and small solution size is required.Operating over an input voltage range of +4.5 V to +60 V, theADP1031 generates isolated output voltages of +6 V to +28 V(adjustable version) or+ 21 V and +24 V (fixed versions) forVOUT1, factory programmable voltages of +5.15 V, +5.0 V, or+3.3 V for VOUT2, and an adjustable output voltages of ?24 V to?5 V for VOUT3.By default, the ADP1031 flyback regulator operates at a 250 kHzswitching frequency and the buck and inverting regulators operateat 125 kHz. All three regulators are phase shifted relative to eachother to reduce electromagnetic interference (EMI). The ADP1031can be driven by an external oscillator in the range of 350 kHzto 750 kHz to ease noise filtering in sensitive applications.The digital isolators integrated in the ADP1031 use AnalogDevices, Inc., iCoupler? chip scale transformer technology,optimized for low power and low radiated emissions.The ADP1031 is available in a 9 mm ? 7 mm, 41-lead LFCSP andis rated for a ?40?C to +125?C operating junction temperaturerange.Applications Industrial automation and process control Instrumentation and data acquisition systems Data and power isolation

The ADP1031 is a high performance, isolated micropowermanagement unit (PMU) that combines an isolated flybackdc-to-dc regulator, an inverting dc-to-dc regulator, and abuck dc-to-dc regulator, providing three isolated power rails.Additionally, the ADP1031 contains four, high speed, serialperipheral interface (SPI) isolation channels and three general-purpose isolators for channel to channel applications where lowpower dissipation and small solution size is required.Operating over an input voltage range of +4.5 V to +60 V, theADP1031 generates isolated output voltages of +6 V to +28 V(adjustable version) or+ 21 V and +24 V (fixed versions) forVOUT1, factory programmable voltages of +5.15 V, +5.0 V, or+3.3 V for VOUT2, and an adjustable output voltages of ?24 V to?5 V for VOUT3.By default, the ADP1031 flyback regulator operates at a 250 kHzswitching frequency and the buck and inverting regulators operateat 125 kHz. All three regulators are phase shifted relative to eachother to reduce electromagnetic interference (EMI). The ADP1031can be driven by an external oscillator in the range of 350 kHzto 750 kHz to ease noise filtering in sensitive applications.The digital isolators integrated in the ADP1031 use AnalogDevices, Inc., iCoupler? chip scale transformer technology,optimized for low power and low radiated emissions.The ADP1031 is available in a 9 mm ? 7 mm, 41-lead LFCSP andis rated for a ?40?C to +125?C operating junction temperaturerange.Applications Industrial automation and process control Instrumentation and data acquisition systems Data and power isolation

The ADP1032 is a high performance, isolated micropower management unit (PMU) that combines an isolated flyback and a dc-to-dc regulator providing two isolated power rails. Additionally, the ADP1032 contains four high speed serial peripheral interface (SPI) isolation channels and three general-purpose isolators for channel to channel applications where low power dissipation and small solution size is required. Operating over an input voltage range of 4.5 V to 60 V, the ADP1032 generates isolated output voltages of 6 V to 28 V (adjustable version) or 24 V (fixed version) for VOUT1, and factory programmable voltages of 5.15 V, 5.0 V, or 3.3 V for VOUT2.?By default, the ADP1032 flyback regulator operates at a 250 kHz switching frequency, and the buck regulator operates at 125 kHz.?The two regulators are phase shifted relative to each other to reduce electromagnetic interference (EMI). The ADP1032 can be driven by an external oscillator in the range of 350 kHz to 750 kHz to ease noise filtering in sensitive applications.?The digital isolators integrated in the ADP1032 use Analog Devices, Inc., iCoupler? chip scale transformer technology, optimized for low power and low radiated emissions. The ADP1032 is available in a 9 mm ? 7 mm, 41-lead LFCSP and is rated for a ?40?C to +125?C operating junction temperature range.?

Demonstration circuit 1406A features three LT3746's, a 32-channel 20mA LED driver with buck controller and serial interface. The three LT3746’s are connected in series to control 32 OSRAM RGB LEDs stuffed on the demo board. Each IC drives a separate color. The demo board input voltage range is 9V to 40V and the LED output voltage is 4.2V for the blue and green LEDs, and 3V for the red LEDs. Each channel has an individually adjustable 12-bit (4096-step) grayscale PWM dimming control and a 6-bit (64-step) dot correction current adjustment.  Individual open/short LED and overtemperature flags are sent back during status read-back.  The evaluation software installed in a host computer communicates with the DC1406A via the interface board DC590B, an USB serial controller.