The ADM2861E, ADM2863E, ADM2865E, and ADM2867E are 5.7 kV rms signal and power isolated RS-485 transceivers. These devices are designed for balanced transmission lines and comply with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E). The devices pass radiated emissions testing to the EN 55032 Class B standard with margin on a 2-layer printed circuit board (PCB) using two small external 0402 ferrites on isolated power and ground pins. The device features an integrated, low electromagnetic interference (EMI), isolated dc-to-dc converter, which eliminates the need for an external isolated power supply. The isolation barrier provides immunity to system level electromagnetic compatibility (EMC) standards. The family of isolator devices features ?12 kV contact and ?15 kV air IEC61000-4-2 ESD protection on the RS-485 A, B, Y, and Z pins. The devices also features cable invert pins, allowing the user to quickly correct reversed cable connection on the A, B, Y, and Z bus pins while maintaining full receiver fail-safe performance.Slew rate limited versions are available, which are optimized for low speed over long cable runs, and have a maximum data rate of 500 kbps. Half duplex and full duplex variants are available. The full duplex generics allow independent cable inversion of the driver and receiver for additional flexibility.Applications Heating, ventilation, and air conditioning (HVAC) networks Industrial field buses Building automation Utility networks Energy meters

The ADM2914 is a quad voltage supervisory IC ideally suitedfor monitoring multiple rails in a wide range of applications.Each monitored rail has two dedicated input pins, VHx and VLx, which allow each rail to be monitored for both overvoltage (OV) and undervoltage (UV) conditions. A common active lowundervoltage (UV) and overvoltage (OV) pin is shared by each of the monitored voltage rails.The ADM2914 includes a 1 V buffered reference output, REF,that acts as an offset when monitoring a negative voltage. Thethree-state SEL pin determines the polarity of the third andfourth inputs, that is, it configures the device to monitorpositive or negative supplies.The device incorporates an internal shunt regulator that enablesthe device to be used in higher voltage systems. This featurerequires a resistor to be placed between the main supply rail andthe VCC pin to limit the current flow into the VCC pin to no greater than 10 mA. The ADM2914 uses the internal shuntregulator to regulate VCC if the supply line exceeds the absolute maximum ratings.The ADM2914 is available in two models. The ADM2914-1offers a latching overvoltage output that can be cleared by toggling the LATCH input pin. The ADM2914-2 has a disablepin that can override and disable both the OV and UVoutputsignals.The ADM2914 is available in a 16-lead QSOP package. Thedevice operates over the extended temperature range of ?40?Cto +125?C.Applications Server supply monitoring FPGA/DSP core and I/O voltage monitoring Telecommunications equipment Medical equipment

The ADM3054 is a 5 kV rms signal isolated controller areanetwork (CAN) physical layer transceiver. The ADM3054complies with the ISO 11898 standard.The device employs Analog Devices, Inc., iCoupler? technologyto combine a 3-channel isolator and a CAN transceiver into asingle package. The logic side of the device is powered with asingle 3.3 V or 5 V supply on VDD1 and the bus side uses a single5 V supply on VDD2 only. Loss of power on the bus side (VDD2)can be detected by an integrated VDD2SENSE signal.The ADM3054 creates an isolated interface between the CANprotocol controller and the physical layer bus. It is capable ofrunning at data rates of up to 1 Mbps.The device has integrated protection on the bus pins, CANHand CANL against shorts to power/ground in 24 V systems.The device has current-limiting and thermal shutdown featuresto protect against output short circuits and situations where thebus might be shorted to ground or power terminals. The part isfully specified over the industrial temperature range and isavailable in a 16-lead, wide-body SOIC package.Applications CAN data buses Industrial field networks

The ADM3095E is a 3.0 V to 5.5 V, 2.5 Mbps, RS-485 transceiverthat features up to ?42 V ac/dc peak bus overvoltage faultprotection on the RS-485 bus pins. This device is designed towithstand overvoltage faults, such as short circuits directly to powersupplies, and overvoltage faults, such as ?24 V ac suppliesconnected in error to the RS-485 A and B bus pins. TheADM3095E is an RS-485 transceiver that integrates IEC 61000-4-5Level 4 surge protection, allowing up to ?4 kV protection onthe RS-485 bus pins. The device has IEC 61000-4-4 Level 4electrical fast transient (EFT) protection up to ?2 kV, andIEC 61000-4-2 Level 4 electrostatic discharge (ESD) protectionon the bus pins, allowing the device to withstand up to ?15 kVon the transceiver interface pins without latch-up or damage.This device has an extended common-mode input voltage rangeof ?25 V to improve data communication reliability in noisyenvironments over long cable lengths where ground loop voltagesare possible. The combination of extended common-mode inputvoltage range, overvoltage fault protection, surge protection, EFTprotection, and ESD protection make the ADM3095E acompletely integrated electromagnetic compatibility (EMC)protected RS-485 transceiver.The ADM3095E also features a logic supply pin, VIO, for a flexibledigital interface, operational to voltages as low as 1.62 V. TheADM3095E is PROFIBUS? compliant with a high driverdifferential output voltage, VOD, of 2.1 V minimum at power supplyvoltages greater than 4.5 V. The device is fully characterized overextended operating temperature ranges, with options of ?40?C to+125?C, and is available in a 16-lead, narrow body SOIC package..Applications Heating ventilation and air conditioning (HVAC) networks Industrial field buses Building automation Utility networks

The ADM3252E is a high speed, 2.5 kV fully isolated, dual-channel RS-232/V.28 transceiver device that is operational from a single 3.3 V or 5 V power supply. Because of high ESD protection on the RIN1, RIN2, TOUT1, and TOUT2?pins, the ADM3252E is ideally suited for operation in electrically harsh environments or where RS-232 cables are frequently plugged and unplugged.The ADM3252E provides four independent isolation channels using the integrated and isolated power of?isoPower?. There is no requirement to use a separate isolated dc-to-dc converter. Chip scale transformer iCoupler? technology from Analog Devices, Inc., is used for both the isolation of the logic signals and the integrated dc-to-dc converter. The result is a total isolation solution.isoPower? technology in the ADM3252E uses high frequency switching elements to transfer power through its transformer. Special care must be taken during printed circuit board (PCB) layout to meet emissions standards. Refer to Application Note AN-0971, Recommendations for Control of Radiated Emissions with isoPower Devices, for details on board layout considerations.The ADM3252E conforms to the EIA/TIA-232E and ITU-T V.28 specifications and operates at data rates of up to 460 kbps. Four external 0.1 ?F charge pump capacitors are used for the voltage doubler/inverter, permitting operation from a single 3.3 V or 5 V supply. The ADM3252E is available in a 44-ball, chip scale package ball grid array (CSP_BGA) and is specified over the ?40?C to +85?C temperature range.APPLICATIONS Isolated RS-232 interface High noise data communications Industrial communications Industrial/telecommunications diagnostic ports Medical equipment

Based on the iCoupler? and isoPower? chip scale transformertechnology, the ADM3260 is a hot swappable digital and powerisolator with two nonlatching, bidirectional communicationchannels, supporting a complete isolated I2C interface, and anintegrated isolated dc-to-dc converter, supporting up to150 mW of isolated power conversion.iCoupler is a chip scale transformer technology with functional,performance, size, and power consumption advantages ascompared to optocouplers. The bidirectional I2C channels eliminate the need for splitting I2C signals into separate transmitand receive signals for use with standalone optocouplers.Based on the Analog Devices, Inc., isoPower technology, theon-chip isolated dc-to-dc converter provides a regulated, isolatedvoltage of 3.15 V to 5.25 V with up to 150 mW of output power.With the ADM3260, the iCoupler and isoPower channels, alongwith the I2C transceivers, can be integrated with semiconductorcircuitry, which enables a complete isolated I2C interface andallows the power converter to be implemented in a small formfactor. The ADM3260 is available in 20-lead SSOP package andhas an operating temperature range of ?40?C to+105?C.isoPower uses high frequency switching elements to transfer powerthrough its transformer. Special care must be taken during printedcircuit board (PCB) layout to meet emissions standards. See theAN-0971 Application Note for board layout recommendationsApplications Isolated I2C, SMBus, and PMBus interfaces Multilevel I2C interfaces Central office switching Telecommunication and data communication equipment ?48 V distributed power systems ?48 V power supply modules Networking

The ADM4168E is a dual RS-422 transceiver suitable for high speed communication on point to point and multidrop transmission lines. The ADM4168E is designed for balanced transmission lines and complies with TIA/EIA-422-B. The differential driver outputs and receiver inputs feature electrostatic discharge (ESD) circuitry that provides protection up to ?15 kV human body model (HBM) and ?8 kV IEC 61000-4-2 (contact and air discharge). The ADM4168E operates from a single 5 V power supply. Excessive power dissipation caused by bus contention or output shorting is prevented by short-circuit protection circuitry. Short-circuit protection circuits limit the maximum output current to ?150 mA during fault conditions. The receivers of the ADM4168E contain a fail-safe feature that results in a logic high output state if the inputs are unconnected (floating). The ADM4168E is fully specified over the commercial and industrial temperature ranges and is available in a 16-lead TSSOP package.Applications RS-422 interfaces High data rate motor control Single-ended to differential signal conversion Point to point and multidrop transmission systems

The ADN2817/ADN2818 provide the receiver functions of quantization, signal level detect, and clock and data recovery for continuous data rates from 10 Mbps to 2.7 Gbps. The ADN2817/ ADN2818 automatically lock to all data rates without the need for an external reference clock or programming. All SONET jitter requirements are exceeded, including jitter transfer, jitter generation, and jitter tolerance. All specifications are quoted for ?40?C to +85?C ambient temperature, unless otherwise noted.This device, together with a PIN diode and a TIA preamplifier, can implement a highly integrated, low cost, and low power fiber optic receiver.The ADN2817/ADN2818 have many optional features available through an I2C interface. For example, the user can read back the data rate onto which the ADN2817 or ADN2818 is locked, or the user can set the device to lock only to one particular data rate if provisioning of data rates is required. A BERMON circuit provides an estimate of the received bit error rate (BER) without interruption of the data. Alternatively, the user can adjust the data sampling phase to optimize the received BER.The ADN2817/ADN2818 are available in a compact 5 mm ? 5 mm, 32-lead, lead frame chip scale package.ApplicationsSONET OC-1, OC-3, OC-12, OC-48, and all associated FEC rates Fibre Channel, 2? Fibre Channel, GbE, HDTV, and others WDM transponders Regenerators/repeaters Test equipment

The ADN4650/ADN4651/ADN46521 are signal isolated, low voltage differential signaling (LVDS) buffers that operate at up to 600 Mbps with very low jitter.The devices integrate Analog Devices, Inc., iCoupler? technology, enhanced for high speed operation, to provide galvanic isolation of the TIA/EIA-644-A compliant LVDS drivers and receivers. This technology allows drop-in isolation of an LVDS signal chain.Multiple channel configurations are offered, and the LVDS receivers on the ADN4651/ADN4652 include a fail-safe mechanism to ensure a Logic 1 on the corresponding LVDS driver output when the inputs are floating, shorted, or terminated, but not driven.For high speed operation with low jitter, the LVDS and isolator circuits rely on a 2.5 V supply. An integrated on-chip low dropout regulator (LDO) can provide the required 2.5 V from an external 3.3 V power supply. The devices are fully specified over a wide industrial temperature range and are available in a 20-lead, wide body SOIC package with 5 kV rms isolation or a 20-lead SSOP package with 3.75 kV rms isolation.Applications Analog front-end (AFE) isolation Data plane isolation Isolated high speed clock and data links Isolated serial peripheral interface (SPI) over LVDS

The ADN4650/ADN4651/ADN46521 are signal isolated, low voltage differential signaling (LVDS) buffers that operate at up to 600 Mbps with very low jitter.The devices integrate Analog Devices, Inc., iCoupler? technology, enhanced for high speed operation, to provide galvanic isolation of the TIA/EIA-644-A compliant LVDS drivers and receivers. This technology allows drop-in isolation of an LVDS signal chain.Multiple channel configurations are offered, and the LVDS receivers on the ADN4651/ADN4652 include a fail-safe mechanism to ensure a Logic 1 on the corresponding LVDS driver output when the inputs are floating, shorted, or terminated, but not driven.For high speed operation with low jitter, the LVDS and isolator circuits rely on a 2.5 V supply. An integrated on-chip low dropout regulator (LDO) can provide the required 2.5 V from an external 3.3 V power supply. The devices are fully specified over a wide industrial temperature range and are available in a 20-lead, wide body SOIC package with 5 kV rms isolation or a 20-lead SSOP package with 3.75 kV rms isolation.Applications Analog front-end (AFE) isolation Data plane isolation Isolated high speed clock and data links Isolated serial peripheral interface (SPI) over LVDS