The ADAU1966A is a high performance, single-chip digital-to-analog converter (DAC) that provides 16 DACs with differential or single-ended outputs using the Analog Devices, Inc., patented multibit sigma-delta (?-?) architecture. A serial peripheral interface (SPI)/I2C port is included, allowing a microcontroller to adjust volume and many other parameters. The ADAU1966A operates from 2.5 V digital and 3.3 V analog supplies. A linear regulator is included to generate the digital supply voltage from the analog supply voltage. The ADAU1966A is available in an 80-lead LQFP.The ADAU1966A is designed for low EMI. This consideration is apparent in both the system and circuit design architectures. By using the on-board PLL to derive the internal master clock from an external left-right frame clock (LRCLK), the ADAU1966A can eliminate the need for a separate high frequency master clock and can be used with or without a bit clock. The DACs are designed using the latest Analog Devices continuous time architectures to further minimize EMI. By using 2.5 V digital supplies, power consumption is minimized, and the digital waveforms are a smaller amplitude, further reducing emissions.Note that throughout this data sheet, multifunction pins, such as SCLK/SCL, are referred to by the entire pin name or by a single function of the pin, for example, SCLK, when only that function is relevant.APPLICATIONS Automotive audio systems Home theater systems Digital audio effects processors

The ADAU7118 converts four stereo pulse density modulation (PDM) bitstreams into one pulse code modulation (PCM) output stream. The source for the PDM data can be eight microphones or other PDM sources. The PCM audio data is output on a serial audio interface port in either inter-IC serial (I2S) or time domain multiplexed (TDM) format.The ADAU7118 is specified over the commercial temperature range (?40?C to +85?C). The ADAU7118 is available in a 16-lead, 3 mm ? 3 mm, 0.40 mm pitch, lead frame chip scale package (LFCSP).Note that throughout this data sheet, multifunction pins, such as ADDR/CONFIG, are referred to either by the entire pin name or by a single function of the pin, for example, ADDR, when only that function is relevant.Applications Microphone arrays Mobile computing Portable electronics Consumer electronics Professional electronics

The ADcmXL3021 is a complete vibration sensing system that combines high performance vibration sensing (using micro-electromechanical systems (MEMS) accelerometers) with a variety of signal processing functions to simplify the development of smart sensor nodes in condition-based monitoring (CBM) systems. The typical ultralow noise density (26 ?g/?Hz) in the MEMS accelerometers supports excellent resolution. The wide bandwidth (dc to 10 kHz within 3 dB flatness) enables tracking of key vibration signatures on many machine platforms.The signal processing includes high speed data sampling (220 kSPS), 4096 time sample record lengths, filtering, windowing, fast Fourier transform (FFT), user configurable spectral or time statistic alarms, and error flags. The serial peripheral interface (SPI) provides access to a register structure that contains the vibration data and a wide range of user configurable functions.The ADcmXL3021 is available in a 23.7 mm ? 27.0 mm ? 12.4 mm aluminum package with four mounting flanges to support installation with standard machine screws. This package provides consistent mechanical coupling to the core sensors over a broad frequency range. The electrical interface is through a 14-pin connector on a 36 mm flexible cable, which enables a wide range of location and orientation options for system mating connectors.The ADcmXL3021 requires only a single, 3.3 V power supply and supports an operating temperature range of ?40?C to +105?C.Applications Vibration analysis CBM systems Machine health Instrumentation and diagnostics Safety shutoff sensing

The ADCMP396 is a quad, rail-to-rail input, low power comparator ideal for use in general-purpose applications. The device operates from a supply voltage of 2.3 V to 5.5 V and draws a minimal amount of current. The quad ADCMP396 consumes only 41.6 ?A of supply current. The low voltage and low current operation of the ADCMP396 makes it ideal for battery-powered systems.The ADCMP396 features a common-mode input voltage range of 200 mV beyond rails, an offset voltage of 1 mV typical across the full common-mode range, and a UVLO monitor. In addition, the design of the comparator allows a defined output state upon power-up. The comparator generates a logic low output while the supply voltage is less than the UVLO threshold.The ADCMP396 incorporates a 1 V ? 0.9% buffered reference voltage. The reference voltage output can directly connect to the comparator input to serve as the trip value for precise monitoring and detection of positive voltage. It can also act as an offset when monitoring the negative voltage.The ADCMP396 is available in a 16-lead narrow-body SOIC package, and it is specified to operate over the ?40?C to +125?C extended temperature range.APPLICATIONS Battery management/monitoring Power supply detection Window comparator Threshold detectors/discriminators Microprocessor systems

The ADCMP580/ADCMP581/ADCMP582 are ultrafast voltagecomparators fabricated on the Analog Devices, Inc. proprietaryXFCB3 Silicon Germanium (SiGe) bipolar process. TheADCMP580 features CML output drivers, the ADCMP581features reduced swing ECL (negative ECL) output drivers, andthe ADCMP582 features reduced swing PECL (positive ECL)output drivers.All three comparators offer 180 ps propagation delay and 100 psminimum pulse width for 10 Gbps operation with 200 fs randomjitter (RJ). Overdrive and slew rate dispersion are typically lessthan 15 ps.The ?5 V power supplies enable a wide ?2 V to +3 V inputrange with logic levels referenced to the CML/NECL/PECLoutputs. The inputs have 50 ? on-chip termination resistorswith the optional capability to be left open (on an individualpin basis) for applications requiring high impedance input. The CML output stage is designed to directly drive 400 mV into50 ? transmission lines terminated to ground. The NECL outputstages are designed to directly drive 400 mV into 50 ? terminatedto ?2 V. The PECL output stages are designed to directly drive400 mV into 50 ? terminated to VCCO ? 2 V. High speed latchand programmable hysteresis are also provided. The differentiallatch input controls are also 50 ? terminated to an independentVTT pin to interface to either CML or ECL or to PECL logic.The ADCMP580/ADCMP581/ADCMP582 are available in a16-lead LFCSP.Applications Automatic test equipment (ATE) High speed instrumentation Pulse spectroscopy Medical imaging and diagnostics High speed line receivers Threshold detection Peak and zero-crossing detectors High speed trigger circuitry Clock and data signal restoration

The ADCMP600, ADCMP601, and ADCMP602 are very fast comparators fabricated on Analog Devices? proprietary XFCB2 process. These comparators are exceptionally versatile and easy to use. Features include an input range from ? 0.5 V to VCC + 0.2 V, low noise TTL-/CMOS-compatible output drivers, and latch inputs with adjustable hysteresis and/or shutdown inputs.The devices offer 5 ns propagation delay with 10 mV overdrive on 3 mA typical supply current.A flexible power supply scheme allows the devices to operate with a single +2.5 V positive supply and a ?0.5 V to +2.8 V input signal range up to a +5.5 V positive supply with a ?0.5 V to +5.8 V input signal range. Split input/output supplies with no sequencing restrictions on the ADCMP602 support a wide input signal range while still allowing independent output swing control and power savings.The TTL-/CMOS-compatible output stage is designed to drive up to 5 pF with full timing specs and to degrade in a graceful and linear fashion as additional capacitance is added. The comparator input stage offers robust protection against large input overdrive, and the outputs do not phase reverse when the valid input signal range is exceeded. High speed latch and programmable hysteresis features are also provided with a unique single-pin control option.The ADCMP600 is available in both 5-lead SC70 and SOT-23 packages, the ADCMP601 is available in a 6-lead SC70 package, and the ADCMP602 is available in 8-lead MSOP and LSCFP packages.Applications High Speed Instrumentation Clock and Data Signal Restoration Logic Level Shifting or Translation Pulse Spectroscopy High Speed Line Receivers Threshold Detection Peak and Zero-crossing Detectors High Speed Trigger Circuitry Pulse-width Modulators Current-/voltage-controlled Oscillators Automatic Test Equipment (ATE)

The ADE7854A?/?ADE7858A?/?ADE7868A?/?ADE7878A are high accuracy, 3-phase electrical energy measurement ICs with serial interfaces and three flexible pulse outputs. The devices incorporate second-order ?-? analog-to-digital converters (ADCs), a digital integrator, reference circuitry, and all signal processing required to perform total (fundamental and harmonic) active, reactive (ADE7858A, ADE7868A, and ADE7878A), and apparent energy measurement and rms calculations.The ADE7878A can also perform fundamental-only active and reactive energy measurement and rms calculations. A fixed function digital signal processor (DSP) executes the signal processing. The DSP program is stored in the internal ROM memory.The ADE7854A / ADE7858A / ADE7868A / ADE7878A can measure active, reactive, and apparent energy in various 3-phase configurations, such as wye or delta services, with both three and four wires. Aside from regular rms measurements, which are updated every 8 kHz, these devices measure low ripple rms values, which are averaged internally and updated every 1.024 sec. The devices provide system calibration features for each phase, that is, rms offset correction, phase calibration, and gain calibration.The CF1, CF2, and CF3 logic outputs provide a wide selection of power information. All four devices provide total active and apparent powers, as well as the sum of the current rms values; the ADE7858A, ADE7868A, and ADE7878A also provide total reactive powers; the ADE7878A also provides fundamental active and reactive powers.The ADE7854A / ADE7858A / ADE7868A / ADE7878A contain waveform sampling registers that allow access to all ADC outputs. The devices also incorporate power quality measurements, such as short duration low or high voltage detection, short duration high current variation, line voltage period measurement, and angles between phase voltages and currents.Two serial interfaces, serial peripheral interface (SPI) and I2C, can communicate with the devices. A dedicated high speed interface, the high speed data capture (HSDC) port, can be used in conjunction with I2C to provide access to the ADC outputs and real-time power information.The devices have two interrupt request pins, IRQ0 and IRQ1, to indicate that an enabled interrupt event has occurred. For the ADE7868A / ADE7878A, three specially designed low power modes ensure the continuity of energy accumulation when the ADE7868A / ADE7878A are in a tampering situation.

The ADE7880 is high accuracy, 3-phase electrical energy measurement IC with serial interfaces and three flexible pulse outputs. The ADE7880 device incorporates second-order sigma-delta (?-?) analog-to-digital converters (ADCs), a digital integrator, reference circuitry, and all of the signal processing required to perform the total (fundamental and harmonic) active, and apparent energy measurements, rms calculations, as well as fundamental-only active and reactive energy measurements. In addition, the ADE7880 computes the rms of harmonics on the phase and neutral currents and on the phase voltages, together with the active, reactive, and apparent power, and the power factor and harmonic distortion on each harmonic for all phases. Total harmonic distortion plus noise (THD + N) is computed for all currents and voltages. A fixed function digital signal processor (DSP) executes this signal processing. The DSP program is stored in the internal ROM memory.The ADE7880 is suitable for measuring active, reactive, and apparent energy in various 3-phase configurations, such as wye or delta services with both three and four wires. The ADE7880 provides system calibration features for each phase, that is, rms offset correction, phase calibration, and gain calibration. The CF1, CF2, and CF3 logic outputs provide a wide choice of power information: total active powers, apparent powers, or the sum of the current rms values, and fundamental active and reactive powers.The ADE7880 contains waveform sample registers that allow access to all ADC outputs. The devices also incorporate power quality measurements, such as short duration low or high voltage detections, short duration high current variations, line voltage period measurement, and angles between phase voltages and currents. Two serial interfaces, SPI and I2C, can be used to communicate with the ADE7880. A dedicated high speed interface, the high speed data capture (HSDC) port, can be used in conjunction with I2C to provide access to the ADC outputs and real-time power information. The ADE7880 also has two interrupt request pins, IRQ0 and IRQ1, to indicate that an enabled interrupt event has occurred. Three specially designed low power modes ensure the continuity of energy accumulation when the ADE7880 is in a tampering situation. The ADE7880 is available in the 40-lead LFCSP, Pb-free package, pin-for-pin compatible with ADE7854, ADE7858, ADE7868, and ADE7878?devices.APPLICATIONS Energy metering systems Power quality monitoring Solar inverters Process monitoring Protective devices

The ADE7903 is a nonisolated, 3-channel, ?-? analog-to-digital converter (ADC) for the neutral line of polyphase energymetering applications using shunt current sensors. The ADE7903 can also be used for single-phase energy meteringand other standalone ADC applications. The ADE7903 features three 24-bit ADCs. The current ADC provides a 67 dBFSsignal-to-noise ratio (SNR) over a 3.3 kHz signal bandwidth, whereas the voltage ADCs provide an SNR of 72 dBFS over thesame bandwidth. One channel is dedicated to measuring the voltage across a shunt when the shunt is used for current sensing.Up to two additional channels are dedicated to measuring voltages, which are usually sensed using resistor dividers.One voltage channel can be used to measure the temperature of the die via an internal sensor. The ADE7903 includes threechannels: one current channel and two voltage channels.Together with the ADE7912?/ ADE7913, the ADE7903 providesa small form factor, 3-phase isolated solution with a neutralmeasurement. The three phases are isolated with ADE7912 /ADE7913 devices, while the neutral line is not isolated with theADE7903. The ADE7903 configuration and status registers are accessedvia a bidirectional SPI serial port for easy interfacing withmicrocontrollers.The ADE7903 can be clocked from a crystal or an externalclock signal. To minimize the system bill of materials, themaster ADE7912 / ADE7913 can drive the clocks of up to threeadditional ADE7912 / ADE7913 or ADE7903 devices.Multiple ADE7912 / ADE7913 and ADE7903 devices can besynchronized to sample at the same moment and providecoherent outputs. The ADE7903 can also be used individuallyas a standalone ADC. The ADE7903 is available in a 20-lead, Pb-free, wide body SOICpackage.APPLICATIONS 3-phase shunt-based polyphase meters with neutral channel measurement Single-phase meters Power quality monitoring Solar inverters Process monitoring Standalone ADCs Protective devices Isolated sensor interfaces Industrial programmable logic controllers (PLCs)

The ADE7953 is a high accuracy electrical energy measurementIC intended for single phase applications. It measures line voltageand current and calculates active, reactive, and apparent energy,as well as instantaneous rms voltage and current.The device incorporates three ?-? ADCs with a high accuracyenergy measurement core. The second input channel simultaneouslymeasures neutral current and enables tamper detectionand neutral current billing. The additional channel incorporatesa complete signal path that allows a full range of measurements.Each input channel supports independent and flexible gain stages,making the device suitable for use with a variety of current sensorssuch as current transformers (CTs) and low value shunt resistors.Two on-chip integrators facilitate the use of Rogowski coil sensors.The ADE7953 provides access to on-chip meter registers via avariety of communication interfaces including SPI, I2C, and UART.Two configurable low jitter pulse output pins provide outputs thatare proportional to active, reactive, or apparent energy, as well ascurrent and voltage rms. A full range of power quality informationsuch as overcurrent, overvoltage, peak, and sag detection areaccessible via the external IRQ pin. Independent active, reactive,and apparent no-load detections are included to prevent ?metercreep.? Dedicated reverse power (REVP), zero-crossing voltage(ZX), and zero-crossing current (ZX_I) pins are also provided. TheADE7953 energy metering IC operates from a 3.3 V supply voltageand is available in a 28-lead LFCSP package.