The HMC1094LP3E Logarithmic Detector converts RF signals at its input, to a proportional DC voltage at its output. The HMC1094LP3E employs successive compression topology which delivers high dynamic range over a wide input frequency range. As the input power is increased, successive amplifiers move into saturation one by one creating an approximation of the logarithm function. The output of a series of detectors is summed, converted into the voltage domain and buffered to drive the LOGOUT output. The HMC1094LP3E provides a nominal logarithmic slope of +18 mV/dB and an intercept of -113 dBm at 23 GHz. Ideal as a log detector for high volume microwave radio and VSAT applications, the HMC1094LP3E is housed in a compact 3x3 mm RoHS compliant SMT plastic package.Applications Point-to-Point Microwave Radio VSAT Wideband Power Monitoring Receiver Signal Strength Indication (RSSI) Test & Measurement

The HMC1132PM5E is a four-stage, gallium arsenide (GaAs) pseudomorphic high electron mobility transistor (pHEMT), monolithic microwave integrated circuit (MMIC) power amplifier. The device operates from 27 GHz to 32 GHz, providing 24 dB of gain and 29.5 dBm of saturated output power from a 5 V power supply.The HMC1132PM5E exhibits excellent linearity with high output third-order intercept (IP3) of 37 dBm, and it is optimized for high capacity, point to point and point to multipoint radio systems. The amplifier configuration and high gain make the HMC1132PM5E an ideal candidate for last stage signal amplification before the antenna.The HMC1132PM5E amplifier input/outputs (I/Os) are internally matched to 50 ?. The device is housed in a RoHS compliant, premolded cavity, 5 mm ? 5 mm LFCSP package, making the device compatible with high volume surface-mount technology (SMT) assembly equipment.APPLICATIONS Point-to-point radios Point-to-multipoint radios Very small aperture terminals (VSATs) and satellite communication (SATCOM) Military and space

The HMC951B is a compact GaAs MMIC I/Q downconverter in a leadless RoHS compliant SMT package. This device provides a small signal conversion gain of 13 dB with a noise figure of 2 dB and 24 dB of image rejection across the frequency band. The HMC951B utilizes an LNA followed by an image reject mixer which is driven by an LO buffer amplifier. The image reject mixer eliminates the need for a filter following the LNA, and removes thermal noise at the image frequency.I and Q mixer outputs are provided and an external 90? hybrid is needed to select the required sideband. The HMC951B is a much smaller alternative to hybrid style image reject mixer downconverter assemblies, and is compatible with surface mount manufacturing techniques.Applications Point-to-Point &?Point-to-Multi-Point Radio Military Radar, EW & ELINT Satellite Communications

The HMC985ALP4KE is an absorptive VoltageVariable Attenuator (VVA) which operates from 10- 40 GHz and is ideal in designs where an analogDC control signal must be used to control RF signallevels over a 35 dB dynamic range. It features twoshunt-type attenuators which are controlled by twoanalog voltages, Vctl1 and Vctl2. Optimum linearityperformance of the attenuator is achieved by firstvarying Vctl1 of the first attenuation stage from -5V to0V with Vctl2 fixed at -5V. The control voltage of thesecond attenuation stage, Vctl2, should then be variedfrom -5V to 0V with Vctl1 fixed at 0V.If the Vctl1 and Vctl2 pins are connected together it ispossible to achieve the full analog attenuation rangewith only a small degradation in input IP3 performance.Applications include AGC circuits and temperaturecompensation of multiple gain stages in microwavepoint-to-point and VSAT radios.Applications Point-to-Point Radio VSAT Radio Test Instrumentation Microwave Sensors Military, ECM & Radar

The ADF4355-3 allows the implementation of fractional-N orinteger-N phase-locked loop (PLL) frequency synthesizers whenused with an external loop filter and an external referencefrequency. A series of frequency dividers at the output provideoperation from 51.5625 MHz to 6600 MHz.The ADF4355-3 has an integrated VCO with a fundamentaloutput frequency ranging from 3300 MHz to 6600 MHz. Inaddition, the VCO frequency is connected to divide by 1, 2, 4, 8,16, 32, or 64 circuits that allow the user to generate RF outputfrequencies as low as 51.5625 MHz. For applications that requireisolation, the RF output stage can be muted. The mute functionis both pin- and software-controllable.Control of all on-chip registers is through a simple 3-wire interface.The ADF4355-3 operates with analog, digital, charge pump, andVCO power supplies ranging from 3.1515 V to 3.4485 V. TheADF4355-3 also contains hardware and software power-downmodes.Applications Wireless infrastructure (W-CDMA, TD-SCDMA, WiMAX, GSM, PCS, DCS, DECT) Point to point/point to multipoint microwave links Satellites/VSATs Test equipment/instrumentation Clock generation

The ADF4360-2 is a fully integrated integer-N synthesizerand voltage-controlled oscillator (VCO). The ADF4360-2 isdesigned for a center frequency of 2000 MHz. In addition, adivide-by-2 option is available, whereby the user gets an RFoutput of between 925 MHz and 1085 MHz.Control of all the on-chip registers is through a simple 3-wireinterface. The device operates with a power supply rangingfrom 3.0 V to 3.6 V and can be powered down when not in use.Applications Wireless handsets (DECT, GSM, PCS, DCS, WCDMA) Test equipment Wireless LANs CATV equipment

The ADF4360-4 is a fully integrated integer-N synthesizerand voltage-controlled oscillator (VCO). The ADF4360-4 isdesigned for a center frequency of 1600 MHz. In addition, adivide-by-2 option is available, whereby the user gets an RFoutput of between 725 MHz and 875 MHz.Control of all the on-chip registers is through a simple 3-wireinterface. The device operates with a power supply rangingfrom 3.0 V to 3.6 V and can be powered down when not in use.Applications Wireless handsets (DECT, GSM, PCS, DCS, WCDMA) Test equipment Wireless LANs CATV equipment

The LT1997-1 is a difference amplifier that can be used to amplify small differential signals while rejecting large common mode signals making it an ideal choice for current sense applications. It combines a precision operational amplifier with highly-matched resistors to form a one-chip solution to amplify and level shift voltages accurately using no external components. It comes with three standard pin-selectable gain options (10, 20 and 50), which can be further combined to form gains from 0.141 to 80 with accuracy of 0.012% (120ppm). The LT1997-1 also operates with input voltages between V? and V? + 76V (independent of V+), enabling robust operation in demanding industrial environments. Its excellent resistor matching results in a common mode rejection ratio of greater than 109dB (Gain = 10).The resistors maintain their excellent matching over temperature; the matching temperature coefficient is guaranteed less than 1ppm/?C. The resistors are extremely linear with voltage, resulting in a gain nonlinearity of less than 2ppm. The LT1997-1 is fully specified at 5V and ?15V supplies and from ?40?C to 125?C. The device is available in space saving 16-lead MSOP and 4mm ? 4mm DFN14 packages.ApplicationsHigh Side or Low Side Current SensingBidirectional Wide Common Mode Range Current SensingHigh Voltage to Low Voltage Level TranslationIndustrial Data-Acquisition Front-EndsReplacement for Isolation CircuitsDifferential to Single-Ended Conversion

Demonstration circuit 2560A is a 18V, 10A synchronous step-down Silent Switcher®2 with spread spectrum frequency modulation featuring the LT8642S. The demo board is designed for 1.2V output from a 2.8V to 18V input. The LT8642S is a compact, ultralow emission, high efficiency, and high speed synchronous monolithic step-down switching regulator. The integrated bypass capacitors optimize all the fast current loops and make it easier to minimize EMI/EMC emissions by reducing layout sensitivity. Selectable spread spectrum mode can further improve EMI/EMC performance. Fast minimum on-time of 20ns enables high VIN to low VOUT conversion at high frequency. The LT8642S switching frequency can be programmed either via a resistor or external clock over a 200kHz to 3MHz range. The default frequency of demo circuit 2560A is 2MHz. The SYNC pin on the demo board is grounded (JP1 at BURST position) by default for low ripple Burst Mode® operation. To synchronize to an external clock, move JP1 to SYNC and apply the external clock to the SYNC terminal. Spread spectrum mode and forced continuous mode can be selected respectively by moving JP1 shunt. The demo board has an EMI filter installed. This EMI filter can be included by applying the input voltage at the VIN_ EMI terminal. The LT8642S data sheet gives a complete description of the part, operation and application information. The data sheet must be read in conjunction with this demo manual for demo circuit 2560A. The LT8643S is assembled in a 4mm × 4mm LQFN package with exposed pads for low thermal resistance. The layout recommendations for low EMI operation and maximum thermal performance are available in the data sheet section Low EMI PCB Layout and Thermal Considerations.

Demonstration circuit 2910A is low VIN, high efficiency, and dual 2A output µModule DC/DC converter. The board operates by default at a fixed 2MHz and can be synchronized from 1MHz to 3MHz via the MODE/SYNC pin. With its high switching frequency and current mode architecture, a fast transient response to line and load changes is possible without sacrificing stability. The DC2910A can be used in forced continuous mode or pulse skip mode for low noise, or in burst mode operation for high efficiency at light loads. The demo board features the LTM4691, which is available in a low profile 3mm x 4mm x 1.2mm LGA package. Please see the LTM4691 datasheet for more detailed information. It is recommended to read the data sheet for the LTM4691 prior to making any changes to the DC2910A.