TPL0102 256-tap dual-channel digital potentiometer with I2C interface evaluation module

The ADT7310 is a high accuracy digital temperature sensor in a narrow SOIC package. It contains a band gap temperature reference and a 13-bit ADC to monitor and digitize the temperature to a 0.0625?C resolution. The ADC resolution, by default, is set to 13 bits (0.0625 ?C). This can be changed to 16 bits (0.0078 ?C) by setting Bit 7 in the configuration register (Register Address 0x01).The ADT7310 is guaranteed to operate over supply voltages from 2.7 V to 5.5 V. Operating at 3.3 V, the average supply current is typically 210 ?A. The ADT7310 has a shutdown mode that powers down the device and offers a shutdown current of typically 2 ?A. The ADT7310 is rated for operation over the ?55?C to +150?C temperature range.The CT pin is an open-drain output that becomes active when the temperature exceeds a programmable critical temperature limit. The default critical temperature limit is 147?C. The INT pin is also an open-drain output that becomes active when the temperature exceeds a programmable limit. The INT and CT pins can operate in either comparator or interrupt mode.APPLICATIONS Medical equipment Environmental control systems Computer thermal monitoring Thermal protection Industrial process control Power system monitors Hand-held applications

TPS65276TEVM Evaluation Module

Evaluation Board for the LP38502

Single to Single ADC Driver PCB for LMH6611 and LMH6618 (SOT23 package; unstuffed)

L99H02QF, STM8A - Motor Controller/Driver Power Management Evaluation Board

The ADE12011 is a single channel, configurable, isolated?digital input monitoring solution for energy transmission and?distribution applications. The ADE1201 is configured through?the serial port interface (SPI) to perform an isolated measurement?of the digital input that is also called binary input or contact?input. The ADE1201 digital output signal on the DOUT1 pin?reflects the state of the input signal after user configurable?signal conditioning. The SPI protocol supports addressing to?allow up to eight devices sharing one 4-wire SPI port.The ADE1201 application circuit accepts a wide range of input?voltages from ?10 V dc to ?300 V dc, or 8 V rms to 240 V rms.?The programmable wetting current and robust application?circuit enable the device to meet stringent, system level?electromagnetic capability (EMC) requirements.The ADE1201 includes an isoPower? integrated, isolated dc-to-dc?converter that eliminates the need for an external isolated power?supply. The iCoupler? chip scale transformer technology is?used to isolate the logic signals between the high voltage,?isolated side and the low voltage, nonisolated side of the?digital input monitor. This technology creates a small form?factor design that includes data and power isolation.An integrated successive approximation register (SAR)?analog-to-digital converter (ADC) and a programmable gain?amplifier (PGA) from 1? to 10? measure the analog inputs.?The ADC waveforms are available through the SPI port to?allow system level diagnostics.Product Highlights Single channel, configurable, isolated digital input. Single hardware design supports 24 V to 300 V systems. Robust architecture. Enables system level diagnostics.Applications Energy transmission and distribution Multifunction relay protection Substation battery monitoring Bay or substation interlocking Merge unit Circuit breaker status indication Remote terminal unit Building automation1 Protected by U.S. Patent Number 2017/0250043. Other patents pending.

The AD5161 provides a compact 3 mm ? 4.9 mm packagedsolution for 256-position adjustment applications. Thesedevices perform the same electronic adjustment function asmechanical potentiometers or variable resistors, with enhancedresolution, solid-state reliability, and superior low temperaturecoefficient performance.The wiper settings are controllable through a pin selectable SPIor I2C compatible digital interface, which can also be used toread back the wiper register content. When the SPI mode isused, the device can be daisy-chained (SDO to SDI), allowingseveral parts to share the same control lines. In the I2C mode, address pin AD0 can be used to place up to two devices on thesame bus. In this same mode, command bits are available toreset the wiper position to midscale or to shut down the deviceinto a state of zero power consumption.Operating from a 2.7 V to 5.5 V power supply and consumingless than 5 ?A allows for usage in portable battery-operatedapplications.APPLICATIONS Mechanical potentiometer replacement in new designs Transducer adjustment of pressure, temperature, position, chemical, and optical sensors RF amplifier biasing Gain control and offset adjustment?

The LT6604-15 consists of two matched, fully differential amplifiers, each with a 4th order, 15MHz lowpass ?lter. The ?xed frequency lowpass ?lter approximates a Chebyshev response. By integrating a ?lter and a differential amplifier, distortion and noise are made exceptionally low. At unity gain, the measured in band signal-to-noise ratio is an impressive 76dB. At higher gains, the input referred noise decreases, allowing the part to process smaller input differential signals without significantly degrading the signal-to-noise ratio.Gain and phase are highly matched between the two channels. Gain for each channel is independently programmed using two external resistors. The LT6604-15 enables level shifting by providing an adjustable output common mode voltage, making it ideal for directly interfacing to ADCs.The LT6604-15 is fully specified for 3V operation. The differential design enables outstanding performance at a 2VP-P signal level for a single 3V supply. See the back page of this datasheet for a complete list of related single and dual differential amplifiers with integrated 2.5MHz to 20MHz lowpass ?lters.Applications Dual Differential ADC Driver Plus Filter Single-Ended to Differential Converter Matched, Dual, Differential Filter Stage Common Mode Translation of Differential Signals High Speed ADC Antialiasing and DAC Smoothing in Wireless Infrastructure or Networking Applications High Speed Test and Measurement Equipment Medical Imaging

The ADM3061E/ADM3062E/ADM3063E/ADM3064E/ADM3065E/ADM3066E/ADM3067E/ADM3068E are 3.0 V to5.5 V, IEC electrostatic discharge (ESD) protected RS-485transceivers, allowing the devices to withstand ?12 kV contactdischarges on the transceiver bus pins without latch-up ordamage. The ADM3062E/ADM3064E/ADM3066E/ADM3068Efeature a VIO logic supply pin that allows a flexible digital interfacecapable of operating as low as 1.62 V. The ADM3065E/ADM3066E/ADM3067E/ADM3068E aresuitable for high speed, 50 Mbps, bidirectional data communication on multipoint bus transmission lines. The ADM3061E/ADM3062E/ADM3063E/ADM3064E/ADM3065E/ADM3066E/ADM3067E/ADM3068E feature a 1/4 unit load inputimpedance that allows up to 128 transceivers on a bus. TheADM3061E/ADM3062E/ADM3063E/ADM3064E models offerall of the same features as the ADM3065E/ADM3066E/ADM3067E/ADM3068E models at a low 500 kbps data rate thatis suitable for operation over long cable runs. The ADM3061E/ADM3062E/ADM3065E/ADM3066E are halfduplex RS-485 transceivers, fully compliant to the PROFIBUS?standard with increased 2.1 V bus differential voltage at VCC ?4.5 V. The ADM3063E/ADM3064E/ADM3067E/ADM3068Eare full duplex RS-485 transceiver options. The RS-485 transceivers are available in a number of spacesaving packages, including the 10-lead, 3 mm ? 3 mm lead framechip-scale package (LFCSP), the 8-lead or 10-lead, 3 mm ? 3 mmmini small outline package (MSOP), and the 8-lead or 14-lead,narrow body standard small outline packages (SOIC_N).Models with operating temperature ranges of ?40?C to +125?Cand ?40?C to +85?C are available. Excessive power dissipation caused by bus contention or byoutput shorting is prevented by a thermal shutdown circuit. If asignificant temperature increase is detected in the internal drivercircuitry during fault conditions, this feature forces the driveroutput into a high impedance state. The ADM3061E/ADM3062E/ADM3063E/ADM3064E/ADM3065E/ADM3066E/ADM3067E/ADM3068E guarantee alogic high receiver output when the receiver inputs are shorted,open, or connected to a terminated transmission line with alldrivers disabled. Table 2 in the data sheet presents an overview of the ADM3061E/ADM3062E/ADM3063E/ADM3064E/ADM3065E/ADM3066E/ADM3067E/ADM3068E data rate capability across temperature, power supply,and package options. Refer to the Ordering Guide section formodel numbering.APPLICATIONS Industrial fieldbuses Process control Building automation PROFIBUS networks Motor control servo drives and encoders?