MEMS inclinometer kit based on IIS2ICLX

Pressure Sensor Development Tools Pressure sensor kit with Qvar functionality ba

Eaton Corporation

eval board

The AD7291 is a 12-bit, low power, 8-channel, successive approximation analog-to-digital converter (ADC) with an internal temperature sensor.The part operates from a single 3.3 V power supply and features an I2C-compatible interface. The part contains a 9-channel multiplexer and a track-and-hold amplifier than can handle frequencies up to 30 MHz. The device has an on-chip 2.5 V reference that can be disabled to allow the use of an external reference.The AD7291 provides a 2-wire serial interface compatible with I2C interfaces. The I2C interface supports standard and fast I2C interface modes. The AD7291 normally remains in a partial power-down state while not converting and powers up for conversions. The conversion process can be controlled by a command mode where conversions occur across I2C write operations or an autocycle mode selected through software control.The AD7291 includes a high accuracy band gap temperature sensor, which is monitored and digitized by the 12-bit ADC to give a resolution of 0.25?C.The AD7291 offers a programmable sequencer, which enables the selection of a preprogrammable sequence of channels for conversion.On-chip limit registers can be programmed with high and low limits for the conversion results; an out-of-range indicator output (ALERT) becomes active when the programmed high or low limits are violated by the conversion result. This output can be used as an interrupt. Product HighlightsIdeally suited to monitoring system variables in a variety of systems including telecommunications, process control, and industrial control.I2C-compatible serial interface. Standard and fast modes.Automatic partial power-down while not converting to maximize power efficiency.Channel sequencer operation.Integrated temperature sensor with 0.25?C resolution.Out of range indicator that can be software disabled or enabled.

The ADF7020-1 is a low power, highly integrated FSK/ GFSK/ ASK/ OOK/ GOOK transceiver designed for operation in thelow UHF and VHF bands. The ADF7020-1 uses an externalVCO inductor that allows users to set the operating frequencyanywhere between 135 MHz and 650 MHz. Using the divide-by-2circuit allows users to operate the device as low as 80 MHz.The typical range of the VCO is about 10% of the operatingfrequency. A complete transceiver can be built using a smallnumber of external discrete components, making the ADF7020-1 very suitable for price-sensitive and area-sensitiveapplications.The transmit section contains a VCO and low noisefractional-N PLL with output resolution of <1 ppm. Thisfrequency agile PLL allows the ADF7020-1 to be used infrequency-hopping spread spectrum (FHSS) systems. The VCOoperates at twice the fundamental frequency to reduce spuriousemissions and frequency pulling problems.The transmitter output power is programmable in 63 steps from?20 dBm to +13 dBm. The transceiver RF frequency, channelspacing, and modulation are programmable using a simple 3-wire interface. The device operates with a power supply range of2.3 V to 3.6 V and can be powered down when not in useA low IF architecture is used in the receiver (200 kHz),minimizing power consumption and the external componentcount and avoiding interference problems at low frequencies.The ADF7020-1 supports a wide variety of programmablefeatures, including Rx linearity, sensitivity, and IF bandwidth,allowing the user to trade off receiver sensitivity and selectivityfor current consumption, depending on the application. Thereceiver also features a patent-pending automatic frequencycontrol (AFC) loop, allowing the PLL to compensate forfrequency error in the incoming signal.An on-chip ADC provides readback of an integrated temperaturesensor, an external analog input, the battery voltage, or theRSSI signal, which provides savings on an ADC in someapplications. The temperature sensor is accurate to ?10?C overthe full operating temperature range of ?40?C to +85?C. Thisaccuracy can be improved by doing a 1-point calibration atroom temperature and storing the result in memory.Applications Low cost wireless data transfer Wireless medical applications Remote control/security systems Wireless metering Keyless entry Home automation Process and building control

Sockets & Adapters LSM6DSRX adapter board for a standard DIL24 socket

Pressure Sensor Development Tools NPI-19-I2C Evaluation Kit w/ USB & software

The HMC7357 is a three-stage GaAs pHEMT MMIC Medium Power Amplifier that operates between 5.5 and 8.5 GHz. The amplifier provides 29 dB of gain and +35 dBm of saturated output power at 34% PAE from a +8V supply. With an excellent Output IP3 of +41.5 dBm, the HMC7357 is ideal for linear applications such as high capacity point-to-point and point-to-multi-point radios or VSAT/SATCOM applications demanding +35 dBm of efficient saturated output power. The RF I/Os are internally matched to 50 Ohms for ease of use. The HMC7357 is packaged in a leadless 5x5 mm plastic surface mount package and is compatible with surface mount manufacturing techniques.Applications Point-to-Point Radios Point-to-Multi-Point Radios VSAT & SATCOM