The ADM3054 is a 5 kV rms signal isolated controller areanetwork (CAN) physical layer transceiver. The ADM3054complies with the ISO 11898 standard.The device employs Analog Devices, Inc., iCoupler? technologyto combine a 3-channel isolator and a CAN transceiver into asingle package. The logic side of the device is powered with asingle 3.3 V or 5 V supply on VDD1 and the bus side uses a single5 V supply on VDD2 only. Loss of power on the bus side (VDD2)can be detected by an integrated VDD2SENSE signal.The ADM3054 creates an isolated interface between the CANprotocol controller and the physical layer bus. It is capable ofrunning at data rates of up to 1 Mbps.The device has integrated protection on the bus pins, CANHand CANL against shorts to power/ground in 24 V systems.The device has current-limiting and thermal shutdown featuresto protect against output short circuits and situations where thebus might be shorted to ground or power terminals. The part isfully specified over the industrial temperature range and isavailable in a 16-lead, wide-body SOIC package.Applications CAN data buses Industrial field networks

The ADM3095E is a 3.0 V to 5.5 V, 2.5 Mbps, RS-485 transceiverthat features up to ?42 V ac/dc peak bus overvoltage faultprotection on the RS-485 bus pins. This device is designed towithstand overvoltage faults, such as short circuits directly to powersupplies, and overvoltage faults, such as ?24 V ac suppliesconnected in error to the RS-485 A and B bus pins. TheADM3095E is an RS-485 transceiver that integrates IEC 61000-4-5Level 4 surge protection, allowing up to ?4 kV protection onthe RS-485 bus pins. The device has IEC 61000-4-4 Level 4electrical fast transient (EFT) protection up to ?2 kV, andIEC 61000-4-2 Level 4 electrostatic discharge (ESD) protectionon the bus pins, allowing the device to withstand up to ?15 kVon the transceiver interface pins without latch-up or damage.This device has an extended common-mode input voltage rangeof ?25 V to improve data communication reliability in noisyenvironments over long cable lengths where ground loop voltagesare possible. The combination of extended common-mode inputvoltage range, overvoltage fault protection, surge protection, EFTprotection, and ESD protection make the ADM3095E acompletely integrated electromagnetic compatibility (EMC)protected RS-485 transceiver.The ADM3095E also features a logic supply pin, VIO, for a flexibledigital interface, operational to voltages as low as 1.62 V. TheADM3095E is PROFIBUS? compliant with a high driverdifferential output voltage, VOD, of 2.1 V minimum at power supplyvoltages greater than 4.5 V. The device is fully characterized overextended operating temperature ranges, with options of ?40?C to+125?C, and is available in a 16-lead, narrow body SOIC package..Applications Heating ventilation and air conditioning (HVAC) networks Industrial field buses Building automation Utility networks

Based on the iCoupler? and isoPower? chip scale transformertechnology, the ADM3260 is a hot swappable digital and powerisolator with two nonlatching, bidirectional communicationchannels, supporting a complete isolated I2C interface, and anintegrated isolated dc-to-dc converter, supporting up to150 mW of isolated power conversion.iCoupler is a chip scale transformer technology with functional,performance, size, and power consumption advantages ascompared to optocouplers. The bidirectional I2C channels eliminate the need for splitting I2C signals into separate transmitand receive signals for use with standalone optocouplers.Based on the Analog Devices, Inc., isoPower technology, theon-chip isolated dc-to-dc converter provides a regulated, isolatedvoltage of 3.15 V to 5.25 V with up to 150 mW of output power.With the ADM3260, the iCoupler and isoPower channels, alongwith the I2C transceivers, can be integrated with semiconductorcircuitry, which enables a complete isolated I2C interface andallows the power converter to be implemented in a small formfactor. The ADM3260 is available in 20-lead SSOP package andhas an operating temperature range of ?40?C to+105?C.isoPower uses high frequency switching elements to transfer powerthrough its transformer. Special care must be taken during printedcircuit board (PCB) layout to meet emissions standards. See theAN-0971 Application Note for board layout recommendationsApplications Isolated I2C, SMBus, and PMBus interfaces Multilevel I2C interfaces Central office switching Telecommunication and data communication equipment ?48 V distributed power systems ?48 V power supply modules Networking

The ADN4650/ADN4651/ADN46521 are signal isolated, low voltage differential signaling (LVDS) buffers that operate at up to 600 Mbps with very low jitter.The devices integrate Analog Devices, Inc., iCoupler? technology, enhanced for high speed operation, to provide galvanic isolation of the TIA/EIA-644-A compliant LVDS drivers and receivers. This technology allows drop-in isolation of an LVDS signal chain.Multiple channel configurations are offered, and the LVDS receivers on the ADN4651/ADN4652 include a fail-safe mechanism to ensure a Logic 1 on the corresponding LVDS driver output when the inputs are floating, shorted, or terminated, but not driven.For high speed operation with low jitter, the LVDS and isolator circuits rely on a 2.5 V supply. An integrated on-chip low dropout regulator (LDO) can provide the required 2.5 V from an external 3.3 V power supply. The devices are fully specified over a wide industrial temperature range and are available in a 20-lead, wide body SOIC package with 5 kV rms isolation or a 20-lead SSOP package with 3.75 kV rms isolation.Applications Analog front-end (AFE) isolation Data plane isolation Isolated high speed clock and data links Isolated serial peripheral interface (SPI) over LVDS

The ADN4650/ADN4651/ADN46521 are signal isolated, low voltage differential signaling (LVDS) buffers that operate at up to 600 Mbps with very low jitter.The devices integrate Analog Devices, Inc., iCoupler? technology, enhanced for high speed operation, to provide galvanic isolation of the TIA/EIA-644-A compliant LVDS drivers and receivers. This technology allows drop-in isolation of an LVDS signal chain.Multiple channel configurations are offered, and the LVDS receivers on the ADN4651/ADN4652 include a fail-safe mechanism to ensure a Logic 1 on the corresponding LVDS driver output when the inputs are floating, shorted, or terminated, but not driven.For high speed operation with low jitter, the LVDS and isolator circuits rely on a 2.5 V supply. An integrated on-chip low dropout regulator (LDO) can provide the required 2.5 V from an external 3.3 V power supply. The devices are fully specified over a wide industrial temperature range and are available in a 20-lead, wide body SOIC package with 5 kV rms isolation or a 20-lead SSOP package with 3.75 kV rms isolation.Applications Analog front-end (AFE) isolation Data plane isolation Isolated high speed clock and data links Isolated serial peripheral interface (SPI) over LVDS

The ADN4650/ADN4651/ADN46521 are signal isolated, low voltage differential signaling (LVDS) buffers that operate at up to 600 Mbps with very low jitter.The devices integrate Analog Devices, Inc., iCoupler? technology, enhanced for high speed operation, to provide galvanic isolation of the TIA/EIA-644-A compliant LVDS drivers and receivers. This technology allows drop-in isolation of an LVDS signal chain.Multiple channel configurations are offered, and the LVDS receivers on the ADN4651/ADN4652 include a fail-safe mechanism to ensure a Logic 1 on the corresponding LVDS driver output when the inputs are floating, shorted, or terminated, but not driven.For high speed operation with low jitter, the LVDS and isolator circuits rely on a 2.5 V supply. An integrated on-chip low dropout regulator (LDO) can provide the required 2.5 V from an external 3.3 V power supply. The devices are fully specified over a wide industrial temperature range and are available in a 20-lead, wide body SOIC package with 5 kV rms isolation or a 20-lead SSOP package with 3.75 kV rms isolation.Applications Analog front-end (AFE) isolation Data plane isolation Isolated high speed clock and data links Isolated serial peripheral interface (SPI) over LVDS

The ADN4693E-1 is a multipoint, low voltage differential signaling (M-LVDS) transceiver (driver and receiver pair) that can operate at up to 200 Mbps (100 MHz) nonreturn to zero (NRZ). The receiver detects the bus state with a differential input of as little as ?50 mV over the common-mode voltage range of the device. Electrostatic discharge (ESD) protection of up to ?15 kV is implemented on the bus pins. The ADN4693E-1 is designed to the TIA/EIA-899 standard for M-LVDS and complement TIA/EIA-644 LVDS devices with additional multipoint capabilities.The ADN4693E-1 features a Type 1 receiver with 25 mV of hysteresis so that slow-changing signals or loss of input does not lead to output oscillations.This full-duplex device is available in a compact 16-lead, 4 mm ? 4 mm lead frame chip scale package (LFCSP). The ADN4693E-1 is specified over the -40?C to +120?C junction temperature range.APPLICATIONS Backplane and cable multipoint data transmission Multipoint clock distribution Low power, high speed alternative to shorter RS-485 links Networking and wireless base station infrastructure Grid infrastructure and relay protection systems

The ADN4691E?/?ADN4693E?/ ADN4696E /?ADN4697E aremultipoint, low voltage differential signaling (M-LVDS)transceivers (driver and receiver pairs) that can operate at up to200 Mbps (100 MHz). The receivers detect the bus state with adifferential input of as little as 50 mV over a common-modevoltage range of ?1 V to +3.4 V. ESD protection of up to ?15 kVis implemented on the bus pins. The devices adhere to theTIA/EIA-899 standard for M-LVDS and complement TIA/EIA-644 LVDS devices with additional multipoint capabilities.The ADN4691E / ADN4693E are Type 1 receivers with 25 mV ofhysteresis so that slow-changing signals or loss of input does notlead to output oscillations. The ADN4696E / ADN4697E areType 2 receivers exhibiting an offset threshold, guaranteeing theoutput state when the bus is idle (bus-idle fail-safe) or the inputs areopen (open-circuit fail-safe).The devices are available as half-duplex in an 8-lead SOIC package(the ADN4691E / ADN4696E) or as full-duplex in a 14-leadSOIC package (the ADN4693E / ADN4697E).APPLICATIONS Backplane and cable multipoint data transmission Multipoint clock distribution Low power, high speed alternative to shorter RS-485 links Networking and wireless base station infrastructure

The ADPD188GG is a complete photometric system designed to measure optical signals from ambient light and from synchronous reflected light emitting diode (LED) pulses. Synchronous measurement offers best-in-class rejection of ambient light interference, both dc and ac. The module integrates a highly efficient photometric front end, two LEDs, and two photodiode (PD). All of these items are housed in a custom package that prevents light from going directly from the LED to the photodiode without first entering the subject.The front end of the application specific integrated circuit (ASIC) consists of a control block, a 14-bit analog-to-digital converter (ADC) with a 20-bit burst accumulator, and three flexible, independently configurable LED drivers. The control circuitry includes flexible LED signaling and synchronous detection. The analog front end (AFE) features best-in-class rejection of signal offset and corruption due to modulated interference commonly caused by ambient light. The data output and functional configuration occur over a 1.8 V I2C interface or a serial peripheral interface (SPI) port.Applications Optical heart rate monitoring Reflective PPG measurement CNIBP measurement?

The ADT7420 is a high accuracy digital temperature sensoroffering breakthrough performance over a wide industrialrange, housed in a 4 mm ? 4 mm LFCSP package. It contains aninternal band gap reference, a temperature sensor, and a 16-bitADC to monitor and digitize the temperature to 0.0078?Cresolution. The ADC resolution, by default, is set to 13 bits(0.0625?C). The ADC resolution is a user programmable modethat can be changed through the serial interface.The ADT7420 is guaranteed to operate over supply voltages from2.7 V to 5.5 V. Operating at 3.3 V, the average supply current is typically210 ?A. The ADT7420 has a shutdown mode that powersdown the device and offers a shutdown current of typically 2.0 ?Aat 3.3 V. The ADT7420 is rated for operation over the ?40?C to+150?C temperature range.Pin A0 and Pin A1 are available for address selection, giving theADT7420 four possible I2C addresses. The CT pin is an open-drainoutput that becomes active when the temperature exceedsa programmable critical temperature limit. The INT pin is alsoan open-drain output that becomes active when the temperatureexceeds a programmable limit. The INT pin and CT pincan operate in comparator and interrupt event modes.Product Highlights Ease of use, no calibration or correction required by the user. Low power consumption. Excellent long-term stability and reliability. High accuracy for industrial, instrumentation, and medical applications. Packaged in a 16-lead, 4 mm ? 4 mm LFCSP RoHS-compliant package.Applications RTD and thermistor replacement Thermocouple cold junction compensation Medical equipment Industrial control and test Food transportation and storage Environmental monitoring and HVAC Laser diode temperature control