DC1763A-G: Demo Board for the LTC2271 16-Bit, 20Msps Serial Low Noise Dual ADC.

Demonstration circuit 1771A is a single output synchronous buck converter featuring the LTC3867EUF with a 24-lead 4mm × 4mm QFN package. The input voltage range is from 4.5V to 14V and it provides 1.5V at 15A at the output. The DC1771A is configured with a sense resistor. DCR sensing circuit is optional. Using the inductor’s DCR as the sense element instead of the on-board sense resistor saves cost and board space while improving full-load efficiency over 2%, though the sense resistor provides a more accurate current limit.

DC1774A-A: Demo Board for the LTC6430-15 High Linearity Differential RF/IF Amplifier/ADC Driver.

The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The demo manual refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V fully differential input range with a 101dB SNR, consumes only 18mW and achieves ±2LSB INL max with no missing codes at 18-bits. The DC1783A demonstrates the DC and AC performance of the LTC2379-18 in conjunction with the DC590 QuikEval™ and DC718 PScope™ data collection boards.

DC178A: Demo Board for the LTC1418 Low Power, 14-Bit, 200ksps ADC with Serial and Parallel I/O.

The LTM2887 is a complete galvanic digital ?Module? (micromodule) isolator. No external components are required. A single 3.3V or 5V supply powers both sides of the interface through an integrated, isolated DC/DC converter. A logic supply pin allows easy interfacing with different logic levels from 1.62V to 5.5V, independent of the main supply.Available options are compliant with SPI and I2C (master mode only) specifications.The isolated side includes two 5V nominal power supplies, including programmable current limit, each capable of providing more than 100mA of load current. The supplies may be adjusted from their nominal value using a single external resistor.Coupled inductors and an isolation power transformer provide 2500VRMS of isolation between the input and output logic interface. This device is ideal for systems where the ground loop is broken, allowing for a large common mode voltage range. Communication is uninterrupted for common mode transients greater than 30kV/?s.Applications Isolated SPI or I2C Interfaces Industrial Systems Test and Measurement Equipment Breaking Ground Loops

The LTM2885 is a complete galvanically isolated full-duplex RS485/RS422 ?Module? (micromodule) transceiver. No external components are required. A single supply powers both sides of the interface through an integrated, isolated, low noise, efficient 5V output DC/DC converter.Coupled inductors and an isolation power transformer provide 6500VRMS of isolation between the line transceiver and the logic interface. This device is ideal for systems where the ground loop is broken allowing for large common mode voltage variation. Uninterrupted communication is guaranteed for common mode transients up to 50kV/?s.Maximum data rates are 20Mbps or 250kbps in slew limited mode. Transmit data, DI, and receive data, RO, are implemented with event driven low jitter processing. The receiver has a one-eighth unit load supporting up to 256 nodes per bus. A logic supply pin allows easy interfacing with different logic levels from 1.62V to 5.5V, independent of the main supply.Enhanced ESD protection allows this part to withstand up to ?15kV (human body model) on the transceiver interface pins to isolated supplies and ?25kV through the isolation barrier to logic supplies without latch-up or damage.APPLICATIONS Isolated RS485/RS422 Interface Industrial Networks Breaking RS485 Ground Loops Isolated PROFIBUS-DP Networks

DC1796A-G Demo Board for: LTC6360 Very Low Noise Single-Ended SAR ADC Driver with True Zero Output LTC2367-18 18-Bit, 500ksps, Pseudo-Differential Unipolar SAR ADC with 97dB SNR

The LTC3838 is a dual, PolyPhase? synchronous step-down DC/DC switching regulator controller. Two independent channels drive all N-channel power MOSFETs. The controlled on-time, valley current mode control architecture allows for fast transient response and constant frequency switching in steady-state operation, independent of VIN, VOUT and load current. Its load-release transient detection feature significantly reduces overshoot at low output voltages.Differential output voltage sensing, along with a precision internal reference, offers an accurate ?0.67% output regulation on Channel 1, even if the remote output ground deviates from local ground by ?500mV. The second channel can either provide an independent ?1% output, or together with the first channel of this controller, serve as one of the PolyPhase channels for a single-output voltage.The switching frequency can be programmed from 200kHz to 2MHz with an external resistor, and can be synchronized to an external clock. Very low tON and tOFF times allow for near 0% and near 100% duty cycles, respectively. Voltage tracking soft start-up and multiple safety features are provided.See below for a comparison of LTC3838, LTC3838-1 and LTC3838-2. Part Number Description LTC3838 ? ?0.67% Differential Output Voltage Accuracy Over Temperature on Channel 1, ?1% Output Regulation on Channel 2, Separate Per Channel 30mV to 100mV Current Sense Range Controls LTC3838-1 ? ?0.67% Differential Output Voltage Accuracy Over Temperature on Both Channel 1 and Channel 2, Single Pin 30mV/60mV Current Sense Range Controls LTC3838-2 ?0.67% Differential Output Voltage Accuracy With Internal Reference on Channel 1, ?4mV Differential with External Reference Voltage on Channel 2, Fixed 30mV Current Sense Range Applications Distributed Power Systems Point-of-Load Converters Computing Systems Data Communication Systems

Demonstration circuit DC1802A is a wide VIN range, low noise, 250mA buck-boost charge pump featuring the LTC3245EMSE. It has an input supply range of 2.7V to 38V and provides a jumper-selectable 5V, 3.3V, or adjustable output (set to 1.2V) at 250mA.