The AD7770 is an 8-channel, simultaneous sampling ADC. Eightfull sigma-delta (?-?) ADCs are on chip. The AD7770 providesa low input current to allow direct sensor connection. Each inputchannel has a programmable gain stage allowing gains of 1, 2, 4,and 8 to map lower amplitude sensor outputs into the full-scaleADC input range, maximizing the dynamic range of the signalchain. The AD7770 accepts a VREF voltage from 1 V up to 3.6 V.The analog inputs accept unipolar (0 V to VREF) or true bipolar(?VREF/2) analog input signals with 3.3 V or ?1.65 V analogsupply voltages, respectively for PGAGAIN = 1. The analog inputscan be configured to accept true differential, pseudo differential,or single-ended signals to match different sensor outputconfigurations.Each channel contains a PGA, an ADC modulator and asinc3, low latency digital filter. An SRC is provided to allow fineresolution control over the AD7770 ODR. This control can beused in applications where the ODR resolution is required tomaintain coherency with 0.01 Hz changes in the line frequency.The SRC is programmable through the serial port interface (SPI).The AD7770 implements two different interfaces: a data outputinterface and SPI control interface. The ADC data output interfaceis dedicated to transmitting the ADC conversion results fromthe AD7770 to the processor. The SPI writes to and reads fromthe AD7770 configuration registers and for the control andreading of data from the SAR ADC. The SPI can also beconfigured to output the ?-? conversion data.The AD7770 includes a 12-bit SAR ADC. This ADC can beused for AD7770 diagnostics without having to decommissionone of the ?-? ADC channels dedicated to system measurementfunctions. With the use of an external multiplexer, which can becontrolled through the three general-purpose input/output pins(GPIOs), and signal conditioning, the SAR ADC can validatethe ?-? ADC measurements in applications where functionalsafety is required. In addition, the AD7770 SAR ADC includesan internal multiplexer to sense internal nodes.The AD7770 contains a 2.5 V reference and reference buffer. Thereference has a typical temperature coefficient of 10 ppm/?C.The AD7770 offers two modes of operation: high resolution modeand low power mode. High resolution mode provides a higherdynamic range while consuming 10.75 mW per channel; lowpower mode consumes just 3.37 mW per channel at a reduceddynamic range specification.The specified operating temperature range is ?40?C to +105?C,although the device is operational up to +125?C.Applications Protection relays General-purpose data acquisition Industrial process control

The AD7779 is an 8-channel, simultaneous sampling ADC.There are eight full ?-? ADCs on chip. The AD7779 providesan ultralow input current to allow direct sensor connection. Eachinput channel has a programmable gain stage allowing gains of1, 2, 4, and 8 to map lower amplitude sensor outputs into thefull-scale ADC input range, maximizing the dynamic range ofthe signal chain. The AD7779 accepts VREF from 1 V up to 3.6 V.The analog inputs accept unipolar (0 V to VREF/GAIN) or truebipolar (?VREF/GAIN/2 V) analog input signals with 3.3 V or?1.65 V analog supply voltages. The analog inputs can beconfigured to accept true differential, pseudo differential, or singleendedsignals to match different sensor output configurations.Each channel contains an ADC modulator and a sinc3, lowlatency digital filter. An SRC is provided to allow fine resolutioncontrol over the AD7779 ODR. This control can be used inapplications where the ODR resolution is required to maintaincoherency with 0.01 Hz changes in the line frequency. The SRCis programmable through the serial port interface (SPI). TheAD7779 implements two different interfaces: a data outputinterface and SPI control interface. The ADC data outputinterface is dedicated to transmitting the ADC conversionresults from the AD7779 to the processor. The SPI interfaceis used to write to and read from the AD7779 configurationregisters and for the control and reading of data from the SARADC. The SPI interface can also be configured to output the?-? conversion data.The AD7779 includes a 12-bit SAR ADC. This ADC can be usedfor AD7779 diagnostics without having to decommission one ofthe ?-? ADC channels dedicated to system measurement functions.With the use of an external multiplexer, which can becontrolled through the three general-purpose inputs/outputs pins(GPIOs), and signal conditioning, the SAR ADC can be used tovalidate the ?-? ADC measurements in applications wherefunctional safety is required. In addition, the AD7779 SAR ADCincludes an internal multiplexer to sense internal nodes.The AD7779 contains a 2.5 V reference and reference buffer.The reference has a typical temperature coefficient of 10 ppm/?C.The AD7779 offers two modes of operation: high resolutionmode and low power mode. High resolution mode provides ahigher dynamic range while consuming 10.75 mW per channel;low power mode consumes just 3.37 mW per channel at areduced dynamic range specification.The specified operating temperature range is ?40?C to +105?C,although the device is operational up to +125?C.Applications Circuit breakers General-purpose data acquisition Electroencephalography (EEG) Industrial process control

The AD7780 is a complete low power front-end solution for bridge sensor products, including weigh scales, strain gages, and pressure sensors. It contains a precision, low power, 24-bit sigma-delta (?-?) ADC; an on-chip, low noise programmable gain amplifier (PGA); and an on-chip oscillator.Consuming only 330 ?A, the AD7780 is particularly suitable for portable or battery-operated products where very low power is required. The AD7780 also has a power-down mode that allows the user to switch off the power to the bridge sensor and power down the AD7780 when not converting, thus increasing the battery life of the product.For ease of use, all the features of the AD7780 are controlled by dedicated pins. Each time a data read occurs, eight status bits are appended to the 24-bit conversion. These status bits contain a pattern sequence that can be used to confirm the validity of the serial transfer.The on-chip PGA has a gain of 1 or 128, supporting a full-scale differential input of ?5 V or ?39 mV. The device has two filter response options. The filter response at the 16.7 Hz update rate provides superior dynamic performance. The settling time is 120 ms at this update rate. At the 10 Hz update rate, the filter response provides greater than ?45 dB of stop-band attenuation. In load cell applications, this stop-band rejection is useful to reject low frequency mechanical vibrations of the load cell. The settling time is 300 ms at this update rate. Simultaneous 50 Hz/60 Hz rejection occurs at both the 10 Hz and 16.7 Hz update rates.The AD7780 operates with a power supply from 2.7 V to 5.25 V. It is available in a narrow body, 14-lead SOIC package and a 16-lead TSSOP package.ApplicationsWeigh scalesPressure MeasurementIndustrial Process ControlPortable instrumentation

The?AD7790/AD7791 are low-power, complete analog front ends for low frequency measurement applications. The device consumes 65 ?A of current typically when operated with a 3 V power supply and 75 ?A typical when operated with a 5 V power supply with the buffer disabled. The AD7791 contains a 24-bit S-D ADC with one differential input, which can be buffered or unbuffered. The AD7790 is a 16-bit version of the AD7791. The AD7790 has a peak-to-peak resolution of 16 bits at the default output data rate of 16.6 Hz while the AD7789 has a peak to peak resolution of 19 bits, which is equivalent to an effective resolution of 21.5 bits at this output data rate.The device operates from an internal clock. Therefore, the user does not have to supply a clock source to the device. The output data rate from the part is software programmable, allowing rates from 9.5 Hz to 120 Hz. The p-p resolution from the part varies with the programmed output data rate. With an output data rate of 16.6 Hz, simultaneous 50 Hz/60 Hz rejection is achieved. Power supply monitoring is also included.The part can be used in single conversion mode whereby the device powers up, performs a single conversion and then returns to powerdown mode. Alternatively, it can be operated in continuous mode. In continuous conversion mode, the part can be configured to continuously read i.e. the conversions are placed on the serial bus automatically as soon as a conversion is complete (the user does not need to write to the ADC to read the data), assuming that the serial clock is applied to the device.The AD7790/AD7791 is housed in a 10-lead MSOP package.

The AD7903 is a dual 16-bit, successive approximation, analog-to-digital converter (ADC) that operates from a single power supply, VDDx, per ADC. It contains two low power, high speed, 16-bit sampling ADCs and a versatile serial interface port. On the CNVx rising edge, the AD7903 samples the voltage difference between the INx+ and INx? pins. The voltages on these pins usually swing in opposite phases between 0 V and VREF. The externally applied reference voltage of the REFx pins (VREF) can be set independently from the supply voltage pins, VDDx. The power of the device scales linearly with throughput.Using the SDIx inputs, the SPI-compatible serial interface can also daisy-chain multiple ADCs on a single 3-wire bus and provide an optional busy indicator. It is compatible with 1.8 V, 2.5 V, 3 V, or 5 V logic, using the separate VIOx supplies.The AD7903 is available in a 20-lead QSOP package with operation specified from ?40?C to +125?C.APPLICATIONSBattery-powered equipmentCommunicationsAutomated test equipment (ATE)Data acquisitionMedical instrumentationRedundant measurementSimultaneous sampling

The AD7942 is a 14-bit, charge redistribution, successive approximation PulSAR? ADC that operates from a single power supply, VDD, between 2.3 V to 5.5 V. It contains a low power, high speed, 14-bit sampling ADC with no missing codes, an internal conversion clock, and a versatile serial interface port. The part also contains a low noise, wide bandwidth, short aperture delay track-and-hold circuit. On the CNV rising edge, it samples an analog input, IN+, between 0 V to VREF with respect to a ground sense, IN?. The reference voltage, VREF, is applied externally and is set up to be the supply voltage. Its power scales linearly with the throughput.The SPI-compatible serial interface also features the ability, using the SDI input, to daisy-chain several ADCs on a single 3-wire bus and provides an optional busy indicator. It is compatible with 1.8 V, 2.5 V, 3 V, or 5 V logic using a separate supply (VIO).The AD7942 is housed in a 10-lead MSOP or a 10-lead LFCSP package yet fits in the same size footprint as the 8-lead MSOP or SOT-23. Operation for the AD7942 is specified from ?40?C to +85?C.APPLICATIONS Battery-powered equipment Data acquisition Instrumentation Medical instruments Process controls

The AD7946 is a 14-bit, 500 kSPS, charge redistribution successive-approximation Analog-to-Digital Converter which operates from a single 5V power supply, VDD. It contains a very low power high-speed 16-bit sampling ADC with no missing codes, an internal conversion clock and a versatile serial interface port. The part also contains a low noise, wide bandwidth, very short aperture delay track/hold circuit. On the CNV rising edge, it samples an analog input IN+ between 0 V to REF with respect to a ground sense IN-. The reference voltage REF is applied externally and can be set up to the supply voltage.Its power scales linearly with throughput.The SPI compatible serial interface also features the ability, using the SDI input, to daisy chain several ADCs on a single 3 wire bus and provides an optional Busy indicator. It is compatible with 1.8 V, 2.5 V, 3 V or 5 V logic using the separate supply VIO.The AD7946 is housed in a 10-lead ?SOIC or 10-lead QFN (LFCSP) with operation specified from ?40?C to +85?C.Applications Battery-powered equipment Data acquisition Instrumentation Medical instruments Process control

The AD7985 is a 16-bit, 2.5 MSPS successive approximationanalog-to-digital converter (SAR ADC). It contains a low power,high speed, 16-bit sampling ADC, an internal conversion clock,an internal reference (and buffer), error correction circuits, anda versatile serial interface port. On the rising edge of CNV, theAD7985 samples an analog input, IN+, between 0 V and REFwith respect to a ground sense, IN?. The AD7985 features avery high sampling rate turbo mode (TURBO is high) and areduced power normal mode (TURBO is low) for low powerapplications where the power is scaled with the throughput.In normal mode (TURBO is low), the SPI-compatible serial interfacealso features the ability, using the SDI input, to daisy-chainseveral ADCs on a single 3-wire bus and provide an optional busyindicator. It is compatible with 1.8 V, 2.5 V, and 2.7 V suppliesusing the separate VIO supply.The AD7985 is available in a 20-lead LFCSP with operationspecified from ?40?C to +85?C.Applications Battery-powered equipment Communications ATE Data acquisition systems Medical instruments

The AD7994 is a 4-channel, 10- and 12-bit, low power, successive approximation ADCs with an I2C-compatible interface. The parts operate from a single 2.7 V to 5.5 V power supply and feature a 2 ?s conversion time. The parts contain a 4-channel multiplexer and track-and-hold amplifier that can handle input frequencies up to 11 MHz.The AD7994 provides a two-wire serial interface which is compatible with I2C interfaces. The part comes in two versions, AD7994-0 and AD7994-1. Each version allows for a minimum of two different I2C addresses. The I2C interface on the AD7994-0 supports Standard and Fast I2C Interface Modes. The I2C interface on the AD7994-1 supports Standard, Fast and two High-Speed I2C Interface Modes.The AD7994 normally remain in a shutdown state while not converting, and power up only for conversions. The conversion process can be controlled using the CONVST pin, by a command mode where conversions occur across I2C write operations, or an automatic conversion interval mode selected through software control.?The AD7994 require an external reference that should be applied to the REFIN pin and can be in the range of 1.2 V to VDD. This allows the widest dynamic input range to the ADC.?On-chip limit registers can be programmed with high and low limits for the conversion result, and an open-drain, out-of-range indicator output (ALERT) becomes active when the programmed high or low limits are violated by the conversion result. This output can be used as an interrupt.PRODUCT HIGHLIGHTS 2 ?s conversion time with low power consumption. I2C-compatible serial interface with pin-selectable addresses. Two AD7993?/ AD7994 versions allow five AD7993 / AD7994 devices to be connected to the same serial bus. The parts feature automatic shutdown while not converting to maximize power efficiency. Current consumption is 1 ?A max when in shutdown mode. Reference can be driven up to the power supply. Out-of-range indicator that can be software disabled or enabled. One-shot and automatic conversion rates. Registers can store minimum and maximum conversion results.

The EVAL-AD8302-ARDZ shield illustrates the functionality of the AD8302, a gain and phase detector which operates from low frequency up to 2.7 GHz. The voltage outputs of the AD8302 are routed to the ANALOG IN connector of the Arduino base board. This allows the RF power detector’s output voltage to be easily digitized and processed by the Arduino base board’s integrated six-channel ADC.