Evaluation Board, STM32L073VZ MCU, 2.8 " Colour LCD-TFT, ST-LINK USB connector"

LAUNCHPAD DEV BRD FOR MSP430G2XX

Hercules RM57Lx Development Kit

Piccolo TMS320F28069 Isolated controlCARD

EVAL MODULE FOR TPS2411

Wide Vin Switch Mode Regulator Evaluation Module

The ADV7535 provides a MIPI? display serial interface (MIPI/ DSI) input receiver and a High-Definition Multimedia Interface (HDMI?) transmitter output. The DSI receiver input supports DSI video mode operation only, and specifically, only supports non-burst mode with sync pulses. The DSI receiver provides up to four lanes of MIPI/DSI data, each running up to 891 Mbps. The HDMI transmitter supports video resolutions up to a maximum TMDS clock frequency of 148.5 MHz. The ADV7535 also provides an audio input port, which supports the insertion of audio into the HDMI stream.Fabricated in an advanced CMOS process, the ADV7535 is available in a space saving, 49-ball, WLCSP surface-mount package. This package is RoHS-compliant and specified to operate from ?10?C to +85?C.Applications Mobile devices Cellular handsets Digital video cameras Digital still cameras Personal media players Gaming

The ADV7842 is a dual HDMI 1.4 fast switching rReceiver with 12-Bit, 170 MHz video and graphics digitizer and 3D comb filter decoder. It is a highly flexible 36-bit pixel output interface with nternal EDID RAM for HDMI and graphics.The ADV7842 incorporates a dual input HDMI 1.4-compatible receiver that supports all HDTV formats up to 1080p and display resolutions up to UXGA (1600 ? 1200 at 60 Hz).The ADV7842 incorporates Xpressview? fast switching on both input HDMI ports. Using the Analog Devices, Inc., hardware-based HDCP engine that minimizes software overhead, Xpressview technology allows fast switching between any HDMI input ports in less than 1 second.ApplicationsAdvanced TVsPDP HDTVsLCD TVs (HDTV ready)LCD/DLP? rear projection HDTVsCRT HDTVsLCoS? HDTVsAVR video receiversLCD/DLP front projectorsHDTV STBs with PVRProjectors

The analog output ADXL356 and the digital output ADXL357 are low noise density, low 0 g offset drift, low power, 3-axis accelerometers with selectable measurement ranges. The ADXL356B supports the ?10 g and ?20 g ranges, the ADXL356C supports the ?10 g and ?40 g ranges, and the ADXL357 supports the ?10 g, ?20 g, and ?40 g ranges.The ADXL356/ADXL357 offer industry leading noise, minimal offset drift over temperature, and long-term stability, enabling precision applications with minimal calibration.The low drift, low noise, and low power ADXL357 enables accurate tilt measurement in an environment with high vibration. The low noise of the ADXL356 over higherfrequencies is ideal for condition-based monitoring and other vibration sensing applications.The ADXL357 multifunction pin names may be referenced only by their relevant function for either the serial peripheral interface (SPI) or limited I2C interface.Applications Inertial measurement units (IMUs)/altitude and heading reference systems (AHRSs) Platform stabilization systems Structural health monitoring Seismic imaging Tilt sensing Robotics Condition monitoring

The LTC2387-16 is a low noise, high speed, 16-bit 15Msps successive approximation register (SAR) ADC ideally suited for a wide range of applications. The combination of excellent linearity and wide dynamic range makes the LTC2387-16 ideal for high speed imaging and instrumentation applications. No-latency operation provides a unique solution for high speed control loop applications. The very low distortion at high input frequencies enables communications applications requiring wide dynamic range and significant signal bandwidth.To support high speed operation while minimizing the number of data lines, the LTC2387-16 features a serial LVDS digital interface. The LVDS interface has one-lane and two-lane output modes, allowing the user to optimize the interface data rate for each application.Applications High Speed Data Acquisition Imaging Communications Control Loops Instrumentation ATE