The ADE7978, the ADE7933/ADE7932, and ADE7923 form achipset dedicated to measuring 3-phase electrical energy usingshunts as current sensors.The ADE7933/ADE7932 are isolated, 3-channel sigma-deltaanalog-to-digital converters (?-? ADCs) for polyphase energymetering applications that use shunt current sensors.TheADE7923 is a nonisolated, 3-channel ?-? ADC for the neutral linethat uses a shunt current sensor. The ADE7932 features two ADCs,and the ADE7933 and ADE7923 feature three ADCs.One channel is dedicated to measuring the voltage across theshunt when a shunt is used for current sensing. This channelprovides a signal-to-noise ratio (SNR) of 67 dB over a 3.3 kHzsignal bandwidth. Up to two additional channels are dedicatedto measuring voltages, which are usually sensed using resistordividers.The unused voltage channels on the neutral ADE7923 can beused for auxiliary voltage measurements. These channels providean SNR of 75 dB over a 3.3 kHz signal bandwidth. One voltagechannel can be used to measure the temperature of the die viaan internal sensor.The ADE7933 and ADE7923 include three channels: onecurrent channel and two voltage channels. The ADE7932includes one current channel and one voltage channel, but isotherwise identical to the ADE7933.The ADE7933/ADE7932 include isoPower?, an integrated,isolated dc-to-dc converter. Based on the Analog Devices, Inc.,iCoupler? technology, the dc-to-dc converter provides theregulated power required by the first stage of the ADCs at a3.3 V input supply. The ADE7933/ADE7932 eliminate the needfor an external dc-to-dc isolation block. The iCoupler chip scaletransformer technology is used to isolate the logic signalsbetween the first and second stages of the ADC. The result is asmall form factor, total isolation solution. The ADE7923 is thenonisolated version of the ADE7933 that can be used forneutral current measurement when isolation from the neutralline is not required.The ADE7933/ADE7932 and ADE7923 contain a digital interfacethat is specially designed to interface with the ADE7978. Usingthis interface, the ADE7978 accesses the ADC outputs andconfiguration settings of the ADE7933/ADE7932 andADE7923.The ADE7933/ADE7932 are available in a 20-lead, Pb-free, widebodySOIC package with increased creepage. The ADE7923 isavailable in a similar 20-lead, Pb-free, wide-body SOIC packagewithout the increased creepage.The ADE7978 is a high accuracy, 3-phase electrical energymeasurement IC with serial interfaces and three flexible pulseoutputs. The ADE7978 can interface with up to four ADE7933/ADE7932 and ADE7923 devices. The ADE7978 incorporates allthe signal processing required to perform total (fundamental andharmonic) active, reactive, and apparent energy measurementand rms calculations, as well as fundamental-only active andreactive energy measurement and rms calculations. A fixedfunction digital signal processor (DSP) executes this signalprocessing.The ADE7978 measures the active, reactive, and apparent energyin various 3-phase configurations, such as wye or delta services,with both three and four wires. The ADE7978 provides systemcalibration features for each phase, gain calibration, and optionaloffset correction. Phase compensation is also available, but it isnot necessary because the currents are sensed using shunts. TheCF1, CF2, and CF3 logic outputs provide a wide selection ofpower information: total active, reactive, and apparent powers;the sum of the current rms values; and fundamental active andreactive powers. The ADE7978 incorporates power quality measurements, suchas short duration low or high voltage detection, short durationhigh current variations, line voltage period measurement, andangles between phase voltages and currents. Two serial interfaces,SPI and I2C, can be used to communicate with the ADE7978.A dedicated high speed interface?the high speed data capture(HSDC) port?can be used in conjunction with I2C to provideaccess to the ADC outputs and real-time power information.The ADE7978 also has two interrupt request pins, IRQ0 andIRQ1, to indicate that an enabled interrupt event has occurred.The ADE7978 is available in a 28-lead, Pb-free LFCSP package.Applications Shunt-based polyphase meters Power quality monitoring Solar inverters Process monitoring Protective devices Isolated sensor interfaces Industrial PLCs

The ADE9078 is a highly accurate, fully integrated energy metering device. Interfacing with both current transformer (CT) and Rogowski coil sensors, the ADE9078 enables users to develop a 3-phase metrology platform, which achieves high performance for Class 1 up to Class 0.2 meters.The ADE9078 integrates seven high performances ADCs and a flexible DSP core. An integrated high end reference ensures low drift over temperature with a combined drift of less than ?25 ppm/?C maximum per channel, each of which includes a programmable gain amplifier (PGA) and ADC.The ADE9078 offers an integrated flexible waveform buffer that stores samples at a fixed data rate or a sampling rate that varies based on line frequency to ensure 64 points per line cycle. These two options make it easy to implement harmonic analysis in an external processor according to IEC 61000-4-7.Two power modes are provided to enable detection of meter tampering: PSM2 uses a low power comparator to compare current channels to a threshold and indicates whether it is exceeded on the IRQ0 and IRQ1 outputs; PSM1 enables fast measurement of current and voltage rms (xVRMS and xIRMS), active power, and VAR during a tamper.The ADE9078 allows advanced and highly accurate energy measurements, enabling one platform to cover a wide range of meters, through a combination of various high end metrology features and superior analog performance.Applications Polyphase meters Power quality monitoring Protective device

The ADE9322B has highly accurate, 2-channel ?-? analog-to-digital converters (ADCs) with mSure? that converts two analog input signals into a single bit stream output. The device is enabled with an mSure sensor monitoring feature that allows the user to check the overall accuracy of the sensor and signal path to identify accuracy drifts that occur over time on the current and voltage channels, independently. The mSure sensor monitoring feature enables antitampering and meter health capabilities when incorporated into a larger system, including digital isolation, a digital metrology engine (ADE7979), and cloud analytics service. Self calibration with mSure enables the device to automatically calibrate the current and voltage channels to achieve a 1% energy accuracy.The ADE9322B incorporates high performance ADCs. The current channel is designed to interface with a shunt resistor. The voltage channel requires an input from a potential divider. A high speed serial peripheral interface (SPI) port and a universal asynchronous receiver and transmitter (UART) port allows access to the ADE9322B registers.Note that throughout the data sheet, multifunction pins, such as MISO/TX, are referred to either by the entire pin name or by a single function of the pin, for example, MISO, when only that function is relevant.The ADE9322B operates from a 3.3 V supply and is available in a 32-lead LFCSP.APPLICATIONS Shunt-based polyphase energy meters Solar inverters Process monitoring Smart power distribution units Polyphase ac chargers

The ADF4158 is a 6.1 GHz, fractional-N frequency synthesizer with modulation and waveform generation capability. It contains a 25-bit fixed modulus, allowing subhertz resolution at 6.1 GHz. It consists of a low noise digital phase frequency detector (PFD), a precision charge pump, and a programmable reference divider. There is a sigma-delta (?-?) based fractional interpolator to allow programmable fractional-N division. The INT and FRAC registers define an overall N-divider as N = INT + (FRAC/225).The ADF4158 can be used to implement frequency shift keying (FSK) and phase shift keying (PSK) modulation. There are also a number of frequency sweep modes available, which generate various waveforms in the frequency domain, for example, sawtooth and triangular waveforms. Sweeps can be set to run automatically, or each step manually triggered by an external pulse. The ADF4158 features cycle slip reduction circuitry, which leads to faster lock times, without the need for modifications to the loop filter.Control of all on-chip registers is via a simple 3-wire interface. The device operates with a power supply ranging from 2.7 V to 3.3 V and can be powered down when not in use.Applications Frequency modulated continuous wave (FMCW) radar Communications test equipment

The ADF4350 allows implementation of fractional-N orinteger-N phase-locked loop (PLL) frequency synthesizersif used with an external loop filter and external referencefrequency.The ADF4350 has an integrated voltage controlled oscillator(VCO) with a fundamental output frequency ranging from2200 MHz to 4400 MHz. In addition, divide-by-1/2/4/8 or 16circuits allow the user to generate RF output frequencies as lowas 137.5 MHz. For applications that require isolation, the RFoutput stage can be muted. The mute function is both pin- andsoftware-controllable. An auxiliary RF output is also available,which can be powered down if not in use.Control of all the on-chip registers is through a simple 3-wireinterface. The device operates with a power supply rangingfrom 3.0 V to 3.6 V and can be powered down when not in use.Applications Wireless infrastructure (W-CDMA, TD-SCDMA, WiMAX, GSM, PCS, DCS, DECT) Test equipment Wireless LANs, CATV equipment Clock generation

The ADF4351 allows implementation of fractional-N or integer-Nphase-locked loop (PLL) frequency synthesizers when used withan external loop filter and external reference frequency.The ADF4351 has an integrated voltage controlled oscillator (VCO)with a fundamental output frequency ranging from 2200 MHz to4400 MHz. In addition, divide-by-1/-2/-4/-8/-16/-32/-64 circuitsallow the user to generate RF output frequencies as low as 35 MHz.For applications that require isolation, the RF output stage can bemuted. The mute function is both pin- and software-controllable.An auxiliary RF output is also available, which can be powereddown when not in use.Control of all on-chip registers is through a simple 3-wire interface.The device operates with a power supply ranging from 3.0 V to3.6 V and can be powered down when not in usApplications Wireless infrastructure (W-CDMA, TD-SCDMA, WiMAX, GSM, PCS, DCS, DECT) Test equipment Wireless LANs, CATV equipment Clock generation

The ADF7012 is a low power FSK/GFSK/OOK/GOOK/ASK UHF transmitter designed for short-range devices (SRDs). The output power, output channels, deviation frequency, and modulation type are programmable by using four, 32-bit registers.The fractional-N PLL and VCO with external inductor enable the user to select any frequency in the 75 MHz to 1 GHz band. The fast lock times of the fractional-N PLL make the ADF7012 suitable in fast frequency hopping systems. The fine frequency deviations available and PLL phase noise performance facilitates narrow-band operation.There are five selectable modulation schemes: binary frequency shift keying (FSK), Gaussian frequency shift keying (GFSK), binary on-off keying (OOK), Gaussian on-off keying (GOOK), and amplitude shift keying (ASK). In the compensation register, the output can be moved in <1 ppm steps so that indirect compensation for frequency error in the crystal reference can be made.A simple 3-wire interface controls the registers. In power-down, the part has a typical quiescent current of <0.1 ?A.APPLICATIONS Low cost wireless data transfer Security systems RF remote controls Wireless metering Secure keyless entry

The ADF7020 is a low power, low-IF transceiver designed for operation in the license-free ISM bands at 433MHz, 868MHz and 915MHz. It is suitable for circuit applications that meet either the European ETSI EN-300-220 or the North American FCC, Part 15.247 and 15.249 regulatory standards. It operates from a 2.3 V to 3.6V power supply with programmable output power from -16 to +13dBm in 0.3dBm steps. Its receiver sensitivity is -117.5dBm at 1kbits/s in FSK mode or -110.5dBm at 9.6kbits/s. Power consumption is 20mA in receive mode and 30mA in transmit mode (+10dBm output).Other features include on-chip VCO (voltage controlled oscillator), Fractional-N PLL, on-chip 7-bit ADC (analog-to-digital converter), digital received signal strength indication (RSSI), temperature sensor and a patent pending fully automatic AFC loop. This allows the ADF7020 to be used with lower tolerance crystals. Its leakage current is < 1uA in power down mode.This device is suitable for circuit applications that meet the European ETSI-300-220, the North American FCC (Part 15), or the Chinese Short Range Device regulatory standards. A complete transceiver can be built using a small number of external discrete components, making the ADF7020 very suitable for price-sensitive and area-sensitive applications. The transmitter block on the ADF7020 contains a VCO and low noise fractional-N PLL with an output resolution of <1 ppm. This frequency agile PLL allows the ADF7020 to be used in frequency-hopping spread spectrum (FHSS) systems. The VCO operates at twice the fundamental frequency to reduce spurious emissions and frequency-pulling problems.The transmitter output power is programmable in 0.3 dB steps from ?16 dBm to +13 dBm. The transceiver RF frequency and modulation are programmable using a simple 3-wire interface. The device operates with a power supply range of 2.3 V to 3.6 V and can be powered down when not in use.A low IF architecture is used in the receiver (200 kHz), minimizing power consumption and the external component count and avoiding interference problems at low frequencies. The ADF7020 supports a wide variety of programmable features, including Rx linearity, sensitivity, and IF bandwidth, allowing the user to trade off receiver sensitivity and selectivity against current consumption, depending on the application. The receiver also features a patent-pending automatic frequency control (AFC) loop, allowing the PLL to track out the frequency error in the incoming signal.An on-chip ADC provides readback of an integrated temperature sensor, an external analog input, the battery voltage, or the RSSI signal, which provides savings on an ADC in some applications. The temperature sensor is accurate to ?10?C over the full operating temperature range of ?40?C to +85?C. This accuracy can be improved by doing a 1-point calibration at room temperature and storing the result in memory.APPLICATIONS Low cost wireless data transfer Remote control/security systems Wireless metering Keyless entry Home automation Process and building control Wireless voice

The ADF7020 is a low power, low-IF transceiver designed for operation in the license-free ISM bands at 433MHz, 868MHz and 915MHz. It is suitable for circuit applications that meet either the European ETSI EN-300-220 or the North American FCC, Part 15.247 and 15.249 regulatory standards. It operates from a 2.3 V to 3.6V power supply with programmable output power from -16 to +13dBm in 0.3dBm steps. Its receiver sensitivity is -117.5dBm at 1kbits/s in FSK mode or -110.5dBm at 9.6kbits/s. Power consumption is 20mA in receive mode and 30mA in transmit mode (+10dBm output).Other features include on-chip VCO (voltage controlled oscillator), Fractional-N PLL, on-chip 7-bit ADC (analog-to-digital converter), digital received signal strength indication (RSSI), temperature sensor and a patent pending fully automatic AFC loop. This allows the ADF7020 to be used with lower tolerance crystals. Its leakage current is < 1uA in power down mode.This device is suitable for circuit applications that meet the European ETSI-300-220, the North American FCC (Part 15), or the Chinese Short Range Device regulatory standards. A complete transceiver can be built using a small number of external discrete components, making the ADF7020 very suitable for price-sensitive and area-sensitive applications. The transmitter block on the ADF7020 contains a VCO and low noise fractional-N PLL with an output resolution of <1 ppm. This frequency agile PLL allows the ADF7020 to be used in frequency-hopping spread spectrum (FHSS) systems. The VCO operates at twice the fundamental frequency to reduce spurious emissions and frequency-pulling problems.The transmitter output power is programmable in 0.3 dB steps from ?16 dBm to +13 dBm. The transceiver RF frequency and modulation are programmable using a simple 3-wire interface. The device operates with a power supply range of 2.3 V to 3.6 V and can be powered down when not in use.A low IF architecture is used in the receiver (200 kHz), minimizing power consumption and the external component count and avoiding interference problems at low frequencies. The ADF7020 supports a wide variety of programmable features, including Rx linearity, sensitivity, and IF bandwidth, allowing the user to trade off receiver sensitivity and selectivity against current consumption, depending on the application. The receiver also features a patent-pending automatic frequency control (AFC) loop, allowing the PLL to track out the frequency error in the incoming signal.An on-chip ADC provides readback of an integrated temperature sensor, an external analog input, the battery voltage, or the RSSI signal, which provides savings on an ADC in some applications. The temperature sensor is accurate to ?10?C over the full operating temperature range of ?40?C to +85?C. This accuracy can be improved by doing a 1-point calibration at room temperature and storing the result in memory.APPLICATIONS Low cost wireless data transfer Remote control/security systems Wireless metering Keyless entry Home automation Process and building control Wireless voice

The ADF7021 is a low power, highly integrated 2FSK/3FSK/4FSK transceiver. It is designed to operate in the narrowband, license-free ISM bands and licensed bands in the 80 MHz to 650 MHz and 862 MHz to 940 MHz frequency ranges. It has both Gaussian and raised cosine data filtering options to improve spectral efficiency for narrowband applications.It is suitable for circuit applications targeted at European ETSI-EN 300-220, the Japanese ARIB STD-T67, the Chinese Short Range Device regulations, and the North American FCC Part 15, Part 90, and Part 95 regulatory standards. A complete transceiver can be built using a small number of external discrete components, making the ADF7021 very suitable for price-sensitive and area-sensitive applications.The transmit section contains a voltage controlled oscillator (VCO) and a low noise fractional-N PLL with output resolution of <1 ppm. This frequency-agile PLL allows the ADF7021 to be used in frequency hopping spread spectrum (FHSS) systems. The VCO operates at twice the fundamental frequency to reduce spurious emissions and frequency pulling problems. The transmitter output power is programmable in 63 steps from ?16 dBm to +13 dBm and has an automatic power ramp control to prevent spectral splatter and help meet regulatory standards. The transceiver RF frequency, channel spacing, and modulation are programmable using a simple 3-wire interface. The device operates with a power supply range of 2.3 V to 3.6 V and can be powered down when not in use.A low IF architecture is used in the receiver (100 kHz), minimizing power consumption and the external component count while avoiding interference problems at low frequencies. The IF filter has programmable bandwidths of 12.5 kHz, 18.75 kHz, and 25 kHz. The ADF7021 supports a wide variety of programmable features including Rx linearity, sensitivity, and IF bandwidth, allowing the user to trade off receiver sensitivity and selectivity against current consumption, depending on the application. The receiver also features a patent-pending automatic frequency control (AFC) loop with programmable pull-in range, allowing the PLL to track out the frequency error in the incoming signal.An on-chip ADC provides readback of an integrated temperature sensor, an external analog input, the battery voltage, and the RSSI signal, which provides savings on an ADC in some applications. The temperature sensor is accurate to ?10?C over the full operating temperature range of ?40?C to +85?C. This accuracy can be improved by doing a 1-point calibration at room temperature and storing the result in memory.