CC1111 USB Evaluation Module Kit 868/915 MHz

EVAL KIT/SYSTEM MAX5386M, MAX5388, MAX5391, AND MAX5393 (DUA

DC373A-B: Demo Board for the LT1725 General Purpose Isolated Flyback Controller.

The LT5511 mixer is designed to meet the high linearity requirements of cable TV infrastructure downstream transmitters and wireless infrastructure transmit systems. The IC includes a differential LO buffer amplifier driving a double-balanced mixer. The LO, RF and IF ports can be easily matched to a broad range of frequencies for different applications. The high performance capability of the LO buffer allows the use of a single-ended source, thus eliminating the need for an LO balun.The LT5511 mixer delivers +17dBm typical input 3rd order intercept point at 950MHz, and +15.5dBm IIP3 at 1900MHz, with IF input signal levels of ? 5dBm. The input 1dB compression point is typically +6dBm.Applications CATV Downlink Infrastructure Wireless Infrastructure High Linearity Mixer Applications

The LTC3718 is a high current, high efficiency synchronous switching regulator controller for DDR and QDR? memory termination. It operates from an input as low as 1.5V and provides a regulated output voltage equal to (0.5)VIN. The controller uses a valley current control architecture to enable high frequency operation with very low on-times without requiring a sense resistor. Operating frequency is selected by an external resistor and is compensated for variations in VIN and VOUT. The LTC3718 uses a pair of standard 5V logic level N-channel external MOSFETs, eliminating the need for expensive P-channel or low threshold devices.Forced continuous operation reduces noise and RF interference. Fault protection is provided by internal foldback current limiting, an output overvoltage comparator and an optional short-circuit timer. Soft-start capability for supply sequencing can be accomplished using an external timing capacitor. OPTI-LOOP? compensation allows the transient response to be optimized over a wide range of loads and output capacitors.Applications Bus Termination: DDR/QDR Memory, SSTL, HSTL,... Servers, RAID Systems Distributed Power Systems Synchronous Buck with General Purpose Boost

The LTC3406 is a high efficiency monolithic synchronous buck regulator using a constant frequency, current mode architecture. The device is available in an adjustable version and fixed output voltages of 1.5V and 1.8V. Supply current during operation is only 20?A and drops to <=1?A in shutdown. The 2.5V to 5.5V input voltage range makes the LTC3406 ideally suited for single Li-Ion battery-powered applications. 100% duty cycle provides low dropout operation, extending battery life in portable systems. Automatic Burst Mode? operation increases efficiency at light loads, further extending battery life.Switching frequency is internally set at 1.5MHz, allowing the use of small surface mount inductors and capacitors.The internal synchronous switch increases efficiency and eliminates the need for an external Schottky diode. Low output voltages are easily supported with the 0.6V feedback reference voltage. The LTC3406 is available in a low profile (1mm) ThinSOT package.Protected by U.S. Patents, including 6580258, 5481178. ? Vout Fsw Features LTC3406 Adj. 1.5MHz Burst Mode LTC3406-1.2 1.2V 1.5MHz Burst Mode LTC3406-1.5 1.5V 1.5MHz Burst Mode LTC3406-1.8 1.8V 1.5MHz Burst Mode LTC3406B Adj. 1.5MHz Burst Mode Disabled LTC3406B-1.2 1.2V 1.5MHz Burst Mode Disabled LTC3406B-2 Adj. 2.25MHz Burst Mode Disabled LTC3406A Adj. 1.5MHz Low Ripple Burst Mode LTC3406AB Adj. 1.5MHz Burst Mode Disabled LTC3406AB-2 Adj. 2.25MHz Burst Mode Disabled Applications Cellular Telephones Personal Information Appliances Wireless and DSL Modems Digital Still Cameras MP3 Players Portable Instruments

Demonstration circuit 545 features the LT3460, step-up DC/DC converter with 1.3MHz constant frequency in a SC70 package. There are two switching regulator circuits in DC545. The 12V output boost converter (upper circuit) is designed to convert 5V input to 12V output at 70mA of load current and the SEPIC converter (lower circuit) is designed to convert 10V ~ 16V input to 12V at 50mA.

The LT1725 is a monolithic switching regulator controller specifically designed for the isolated flyback topology. It drives the gate of an external MOSFET and is generally powered from a third transformer winding. These features allow for an application input voltage limited only by external power path components. The third transformer winding also provides output voltage feedback information, such that an optoisolator is not required. Its gate drive capability coupled with a suitable external MOSFET can deliver load power up to tens of watts.The LT1725 has a number of features not found on most other switching regulator ICs. By utilizing current mode switching techniques, it provides excellent AC and DC line regulation. Its unique control circuitry can maintain regulation well into discontinuous mode in most applications. Optional load compensation circuitry allows for improved load regulation. An optional undervoltage lockout pin halts operation when the application input voltage is too low. An optional external capacitor implements a soft-start function. A 3V output is available at up to several mA for powering primary side application circuitry.Applications Telecom Isolated Converters Offline Isolated Power Supplies Instrumentation Power Supplies

DC677A: Demo Board for the LTC3900 Synchronous Rectifier Driver for Forward Converters.

Demonstration circuit 857 features the LT3481EMSE and LT3481EDD in two step-down converter circuits, one configured for high efficiency and the other for small size. The high efficiency circuit switching at 800kHz is designed for 3.3V/2A output from a 4.5V to 34V input. The small size circuit switching at 2MHz demonstrates the LT3481’s ability to operate with a small inductor and output capacitor. It is designed for 5V output from an 8.5V to 22V input. The wide input range of the LT3481 allows a variety of input sources. The typical sources are automotive batteries, wall adaptors and industrial supplies. The current mode control scheme creates fast transient response and good loop stability. In addition, the LT3481’s integrated boost diode reduces the parts count. The low ripple Burst Mode® Operation of LT3481 not only allows the circuit to have high efficiency over a broad current range but also provides the low output ripple at light load conditions.