The HMC815B is a compact gallium arsenide (GaAs),pseudomorphic high electron mobility transistor (pHEMT),monolithic microwave integrated circuit (MMIC) upconverterin a RoHS compliant package that operates from 21 GHz to27 GHz. This device provides a small signal conversion gain of12 dB and a sideband rejection of 20 dBc. The HMC815Butilizes a driver amplifier proceeded by an in phase/quadrature(I/Q) mixer where the LO is driven by an active 2? multiplier.IF1 and IF2 mixer inputs are provided, and an external 90?hybrid is needed to select the required sideband. The I/Q mixertopology reduces the need for filtering of unwanted sideband.The HMC815B is a smaller alternative to hybrid style singlesideband (SSB) downconverter assemblies, and it eliminates theneed for wire bonding by allowing the use of surface-mountmanufacturing techniques.The HMC815B is available in 4.90 mm ? 4.90 mm, 32-terminalceramic LCC package and operates over the ?40?C to +85?Ctemperature range. An evaluation board for the HMC815B isalso available upon request.Applications Point to point and point to multipoint radios Military radars, electronic warfare, and electronic intelligence Satellite communications Sensors

The AD7903 is a dual 16-bit, successive approximation, analog-to-digital converter (ADC) that operates from a single power supply, VDDx, per ADC. It contains two low power, high speed, 16-bit sampling ADCs and a versatile serial interface port. On the CNVx rising edge, the AD7903 samples the voltage difference between the INx+ and INx? pins. The voltages on these pins usually swing in opposite phases between 0 V and VREF. The externally applied reference voltage of the REFx pins (VREF) can be set independently from the supply voltage pins, VDDx. The power of the device scales linearly with throughput.Using the SDIx inputs, the SPI-compatible serial interface can also daisy-chain multiple ADCs on a single 3-wire bus and provide an optional busy indicator. It is compatible with 1.8 V, 2.5 V, 3 V, or 5 V logic, using the separate VIOx supplies.The AD7903 is available in a 20-lead QSOP package with operation specified from ?40?C to +125?C.APPLICATIONSBattery-powered equipmentCommunicationsAutomated test equipment (ATE)Data acquisitionMedical instrumentationRedundant measurementSimultaneous sampling

The AD7942 is a 14-bit, charge redistribution, successive approximation PulSAR? ADC that operates from a single power supply, VDD, between 2.3 V to 5.5 V. It contains a low power, high speed, 14-bit sampling ADC with no missing codes, an internal conversion clock, and a versatile serial interface port. The part also contains a low noise, wide bandwidth, short aperture delay track-and-hold circuit. On the CNV rising edge, it samples an analog input, IN+, between 0 V to VREF with respect to a ground sense, IN?. The reference voltage, VREF, is applied externally and is set up to be the supply voltage. Its power scales linearly with the throughput.The SPI-compatible serial interface also features the ability, using the SDI input, to daisy-chain several ADCs on a single 3-wire bus and provides an optional busy indicator. It is compatible with 1.8 V, 2.5 V, 3 V, or 5 V logic using a separate supply (VIO).The AD7942 is housed in a 10-lead MSOP or a 10-lead LFCSP package yet fits in the same size footprint as the 8-lead MSOP or SOT-23. Operation for the AD7942 is specified from ?40?C to +85?C.APPLICATIONS Battery-powered equipment Data acquisition Instrumentation Medical instruments Process controls

The AD7946 is a 14-bit, 500 kSPS, charge redistribution successive-approximation Analog-to-Digital Converter which operates from a single 5V power supply, VDD. It contains a very low power high-speed 16-bit sampling ADC with no missing codes, an internal conversion clock and a versatile serial interface port. The part also contains a low noise, wide bandwidth, very short aperture delay track/hold circuit. On the CNV rising edge, it samples an analog input IN+ between 0 V to REF with respect to a ground sense IN-. The reference voltage REF is applied externally and can be set up to the supply voltage.Its power scales linearly with throughput.The SPI compatible serial interface also features the ability, using the SDI input, to daisy chain several ADCs on a single 3 wire bus and provides an optional Busy indicator. It is compatible with 1.8 V, 2.5 V, 3 V or 5 V logic using the separate supply VIO.The AD7946 is housed in a 10-lead ?SOIC or 10-lead QFN (LFCSP) with operation specified from ?40?C to +85?C.Applications Battery-powered equipment Data acquisition Instrumentation Medical instruments Process control

The AD7985 is a 16-bit, 2.5 MSPS successive approximationanalog-to-digital converter (SAR ADC). It contains a low power,high speed, 16-bit sampling ADC, an internal conversion clock,an internal reference (and buffer), error correction circuits, anda versatile serial interface port. On the rising edge of CNV, theAD7985 samples an analog input, IN+, between 0 V and REFwith respect to a ground sense, IN?. The AD7985 features avery high sampling rate turbo mode (TURBO is high) and areduced power normal mode (TURBO is low) for low powerapplications where the power is scaled with the throughput.In normal mode (TURBO is low), the SPI-compatible serial interfacealso features the ability, using the SDI input, to daisy-chainseveral ADCs on a single 3-wire bus and provide an optional busyindicator. It is compatible with 1.8 V, 2.5 V, and 2.7 V suppliesusing the separate VIO supply.The AD7985 is available in a 20-lead LFCSP with operationspecified from ?40?C to +85?C.Applications Battery-powered equipment Communications ATE Data acquisition systems Medical instruments

The AD7994 is a 4-channel, 10- and 12-bit, low power, successive approximation ADCs with an I2C-compatible interface. The parts operate from a single 2.7 V to 5.5 V power supply and feature a 2 ?s conversion time. The parts contain a 4-channel multiplexer and track-and-hold amplifier that can handle input frequencies up to 11 MHz.The AD7994 provides a two-wire serial interface which is compatible with I2C interfaces. The part comes in two versions, AD7994-0 and AD7994-1. Each version allows for a minimum of two different I2C addresses. The I2C interface on the AD7994-0 supports Standard and Fast I2C Interface Modes. The I2C interface on the AD7994-1 supports Standard, Fast and two High-Speed I2C Interface Modes.The AD7994 normally remain in a shutdown state while not converting, and power up only for conversions. The conversion process can be controlled using the CONVST pin, by a command mode where conversions occur across I2C write operations, or an automatic conversion interval mode selected through software control.?The AD7994 require an external reference that should be applied to the REFIN pin and can be in the range of 1.2 V to VDD. This allows the widest dynamic input range to the ADC.?On-chip limit registers can be programmed with high and low limits for the conversion result, and an open-drain, out-of-range indicator output (ALERT) becomes active when the programmed high or low limits are violated by the conversion result. This output can be used as an interrupt.PRODUCT HIGHLIGHTS 2 ?s conversion time with low power consumption. I2C-compatible serial interface with pin-selectable addresses. Two AD7993?/ AD7994 versions allow five AD7993 / AD7994 devices to be connected to the same serial bus. The parts feature automatic shutdown while not converting to maximize power efficiency. Current consumption is 1 ?A max when in shutdown mode. Reference can be driven up to the power supply. Out-of-range indicator that can be software disabled or enabled. One-shot and automatic conversion rates. Registers can store minimum and maximum conversion results.

The EVAL-AD8302-ARDZ shield illustrates the functionality of the AD8302, a gain and phase detector which operates from low frequency up to 2.7 GHz. The voltage outputs of the AD8302 are routed to the ANALOG IN connector of the Arduino base board. This allows the RF power detector’s output voltage to be easily digitized and processed by the Arduino base board’s integrated six-channel ADC.

The ADA4097-1/ADA4097-2 are single and dual robust, precision, rail-to-rail input and output operational amplifiers (op amps) with inputs that operate from ?VS to +VS and beyond, which are referred to in this data sheet as Over-The-Top?. The devices feature offset voltages of ?VS, independent of the +VS supply.The ADA4097-1/ADA4097-2 are unity-gain stable and can drive loads requiring up to 20 mA per channel. The devices can also drive capacitive loads as large as 200 pF. The amplifiers are available with low power shutdown.The ADA4097-1 is available in a standard, 6-lead thin small outline transistor (TSOT) package. The ADA4097-2 is available in an 8-lead standard small outline (SOIC_N) package, 8-lead mini small outline package (MSOP), and 10-lead lead-frame chip-scale package (LFCSP).APPLICATIONS Industrial sensor conditioning Supply current sensing Battery and power supply monitoring Front-end amplifiers in abusive environments 4 mA to 20 mA transmitters

The ADA4098-1?and ADA4098-2 are single/dual robust, precision, rail-to-rail input and output operational amplifiers (op amps) with inputs that operate from ?VS to +VS and beyond, which is referred to in this data sheet as Over-The-Top?. The devices feature offset voltages of ?VS, independent of the +VS supply.The ADA4098-1 and ADA4098-2 are unity-gain stable and can drive loads requiring up to 20 mA per channel. The devices can also drive capacitive loads as large as 200 pF. The amplifiers are available with low power shutdown.The ADA4098-1 is available in a standard, 6-lead thin small outline transistor (TSOT) package. The ADA4098-2 is available in an 8-lead standard small outline (SOIC_N) package, 8-lead mini small outline package (MSOP), and 10-lead lead-frame chip-scale package (LFCSP).APPLICATIONS Industrial sensor conditioning Supply current sensing Battery and power supply monitoring Front-end amplifiers in abusive environments 4 mA to 20 mA transmitters

The ADA4523-1 is a high voltage, low noise, zero drift op amp that offers precision dc performance over a wide supply range of 4.5 V to 36 V. Offset voltage and 1/f noise are suppressed, allowing this op amp to achieve a maximum offset voltage of ?4 ?V and a 0.1 Hz to 10 Hz input noise voltage of 88 nV p-p typical.The self calibrating circuitry of the ADA4523-1 results in low offset voltage drift with temperature (0.01 ?V/?C maximum) and zero drift over time. Additionally, the ADA4523-1 uses on-chip filtering to achieve high immunity to electromagnetic interference (EMI). Wide supply range, combined with low noise, low offset, 168 dB power supply rejection ratio (PSRR), and 160 dB common-mode rejection ratio (CMRR), make the ADA4523-1 well suited for high dynamic range test, measurement, and instrumentation systems.?Applications High resolution data acquisition Reference buffering Test and measurement Electronic scales Thermocouple amplifiers Strain gages Low-side current sense