The ADL5906 is a true rms responding power detector that has a 67 dB measurement range when driven with a single-ended 50 ? source. The easy to use input makes the ADL5906 frequency versatile by eliminating the need for a balun or any other form of external input tuning for operation up to 10 GHz.The ADL5906 provides a solution in a variety of high frequency systems requiring an accurate rms measurement of signal power. The ADL5906 can operate from 10 MHz to 10 GHz and can accept inputs from ?65 dBm to +8 dBm with varying crest factors and bandwidths, such as GSM-EDGE, CDMA, W-CDMA,TD-SCDMA, WiMAX, and OFDM-based LTE carriers. In addition, its temperature stability over the broad temperature range of ?55?C to +125?C makes it ideally suited for a wide array of communications, military, industrial, and instrumentation applications.Used as a power measurement device, VRMS is connected to VSET. The output is then proportional to the logarithm of the rms value of the input. In other words, the reading is presented directly in decibels and is scaled 1.1 V per decade, or 55 mV/dB; other slopes are easily arranged. In controller mode, the voltage applied to VSET determines the power level required at the input to null the deviation from the setpoint. The output buffer can provide high load currents.Requiring only a single supply of 5 V and a few capacitors, it is easy to use and capable of being driven single-ended or with a balun for differential input drive. The ADL5906 has a low 250 ?A sleep current when powered down by a logic high applied to the PWDN pin. It powers up within approximately 1.4 ?s to its nominal operating current of 68 mA at 25?C.The ADL5906 is supplied in a 4 mm ? 4 mm, 16-lead LFCSP and it is pin compatible with the ADL5902 and the AD8363 TruPwr? rms detectors. This feature allows the designer to create one circuit layout for projects requiring different dynamic ranges. A fully populated RoHS-compliant evaluation board is available.Applications Power amplifier linearization/control loops Transmitter signal strength indication (TSSI) RF instrumentation

The ADL5960 is a wideband vector network analyzer front-end consisting of a resistive bidirectional bridge, down-conversion mixers, programmable IF amplifiers and filters, and a highly flexible local oscillator (LO) interface. The bridge provides >10 dB of directivity up to 17 GHz, and the primary transmission line of the bridge, from RFIN to RFOUT, is wideband impedance matched to 50 ? and has a flat frequency response with The ADL5960 supports several different LO interface configurations that simplify the clocking design of a VNA solution as well as the interfacing of the device to an analog-to-digital converter (ADC). The frequency divider and multipliers in the LO interface enable measurement sweeps beyond the operating frequency range of the source driving the (LOP and LOM) pins. This enables operation over the full 20 GHz bandwidth of the ADL5960 using a 6 GHz synthesizer as the LO source. The IF frequency offset mixer, driven through the (OFP and OFM) interface, enables further simplification by allowing the (swept) RF and LO signals to be driven by the same frequency source. The frequency of the IF output signals is then determined by the low-frequency source driving the (OFP and OFM) interface. Driving this interface at the ADC sample frequency with the divide by 4 enabled, automatically centers the IF output signal in the first Nyquist zone.The IF filters with programmable bandwidth and IF amplifiers with individually programmable gain enable simultaneous dynamic range optimization of the IF signals at the incident channel (IFFP and IFFM) and reverse channel (IFRP and IFRM) IF interfaces. The IF amplifiers have an adjustable output common-mode level and sufficient drive capability to interface directly with a wide range of ADCs.All configurations and functions in the ADL5960 are fully programmable through a 3-wire serial peripheral interface (SPI) using the ADI-SPI interface standard. The ADL5960 is offered in a small footprint 26-lead, 3 mm ? 4 mm LFCSP.APPLICATIONSBroadband, multi-port vector network analyzersS-parameter magnitude and phase measurementIn-line RF power measurementAutomated test equipmentReflectometersMaterials analysis

The ADL6316 is a transmit variable gain amplifier (VGA) that?provides an interface from radio frequency digital-to-analog?converters (RF DACs), transceivers, and systems on a chip (SoC)?to power amplifiers. Integrated balun and hybrid couplers allow?high performance RF capability in the frequency range of?500 MHz to 1000 MHz.To optimize performance vs. power level, the ADL6316 includes?a voltage variable attenuator (VVA), high linearity amplifiers,?and a digital step attenuator (DSA). All of the devices integrated?into the ADL6316 are programmable via a 4-wire serial port?interface (SPI).The ADL6316 is manufactured on an advanced silicon germanium?(SiGe), bipolar complementary metal-oxide semiconductor?(BiCMOS) process.Applications 2G/3G/4G/long-term evolution (LTE) in FDD/TDD broadband?communication systems

The ADM1270 is a current-limiting controller that providesinrush current limiting and overcurrent protection for modularor battery-powered systems. When circuit boards are insertedinto a live backplane, discharged supply bypass capacitors drawlarge transient currents from the backplane power bus as theycharge. These transient currents can cause permanent damageto connector pins, as well as dips on the backplane supply thatcan reset other boards in the system.The ADM1270 is designed to control the inrush current, whenpowering on the system, via an external P-channel field effecttransistor (FET).To protect the system from a reverse polarity input supply, thereis a provision made to control an additional external P-channelFET. This feature prevents reverse current flow in case of a reversepolarity connection, which can damage the load or the ADM1270.The ADM1270 is available in a 3 mm ? 3 mm, 16-lead LFCSP anda 16-lead QSOP. Applications Industrial modules Battery-powered/portable instrumentation

TThe ADM7154 is a linear regulator that operates from 2.3 V to5.5 V and provides up to 600 mA of load current. Using anadvanced proprietary architecture, it provides high powersupply rejection and ultralow noise, achieving excellent line andload transient response with only a 10 ?F ceramic output capacitor.There are 16 standard output voltages for the ADM7154. Thefollowing voltages are available in stock: 1.2 V, 1.8 V, 2.5 V, 2.8 V,3.0 V, and 3.3 V. Additional voltages are available by specialorder: 1.3 V, 1.5 V, 1.6 V, 2.0 V, 2.2 V, 2.6 V, 2.7 V, 2.9 V, 3.1 V,and 3.2 V.The ADM7154 regulator typical output noise is 0.9 ?V rms from100 Hz to 100 kHz for fixed output voltage options and1.5 nV/?Hz for noise spectral density from 10 kHz to 1 MHz. The ADM7154 is available in 8-lead, 3 mm ? 3 mm LFCSP and8-lead SOIC packages, making it not only a very compactsolution, but also providing excellent thermal performance forapplications requiring up to 600 mA of load current in a small,low profile footprint.Applications Regulation to noise sensitive applications: PLLs, VCOs, and PLLs with integrated VCOs Communications and infrastructure Backhaul and microwave links

The ADM7170 is a CMOS, low dropout linear regulator (LDO) that operates from 2.3 V to 6.5 V and provides up to 500 mA of output current. This high output current LDO is ideal for regulation of high performance analog and mixed signal circuits operating from 6 V down to 1.2 V rails. Using an advanced proprietary architecture, the device provides high power supply rejection and low noise, and achieves excellent line and load transient response with just a small 4.7 ?F ceramic output capacitor. Load transient response is typically 1.5 ?s for a 1 mA to 500 mA load step.The ADM7170 is available in 17 fixed output voltage options. The following voltages are available from stock: 1.3 V, 1.8 V, 2.5 V, 3.0 V, 3.3 V, 4.2 V, and 5.0 V. Additional voltages that are available by special order are: 1.5 V, 1.85 V, 2.0 V, 2.2 V, 2.7 V, 2.75 V, 2.8 V, 2.85 V, 3.8 V, and 4.6 V. An adjustable version is also available that allows output voltages that range from 1.2 V to VIN ? VDO with an external feedback divider.Inrush current can be controlled by adjusting the start-up time via the soft start pin. The typical start-up time with a 1 nF soft start capacitor is about 1.0 ms.The ADM7170 regulator output noise is 5 ?V rms independent of the output voltage. The ADM7170 is available in an 8-lead, 3 mm ? 3 mm LFCSP, making it not only a very compact solution, but also providing excellent thermal performance for applications requiring up to 500 mA of output current in a small, low profile footprint.Applications Regulation to noise sensitive applications: ADC and DAC circuits, precision amplifiers, PLLs/VCOs, and clocking ICs Communications and infrastructure Medical and healthcare Industrial and instrumentation

The ADM7171 is a CMOS, low dropout linear regulator (LDO) that operates from 2.3 V to 6.5 V and provides up to 1 A of output current. This high output current LDO is ideal for regulation of high performance analog and mixed signal circuits operating from 6 V down to 1.2 V rails. Using an advanced proprietary architecture, the device provides high power supply rejection and low noise, and achieves excellent line and load transient response with just a small 4.7 ?F ceramic output capacitor. Load transient response is typically 1.5 ?s for a 1 mA to 500 mA load step.The ADM7171 is available in 17 fixed output voltage options. The following voltages are available from stock: 1.3 V, 1.8 V, 2.5 V, 3.0 V, 3.3 V, 4.2 V, and 5.0 V. Additional voltages that are available by special order are: 1.5 V, 1.85 V, 2.0 V, 2.2 V, 2.7 V, 2.75 V, 2.8 V, 2.85 V, 3.8 V, and 4.6 V. An adjustable version is also available that allows output voltages that range from 1.2 V to VIN ? VDO with an external feedback divider.Inrush current can be controlled by adjusting the start-up time via the soft start pin. The typical start-up time with a 1 nF soft start capacitor is 1.0 ms.The ADM7171 regulator output noise is 5 ?V rms independent of the output voltage. The ADM7171 is available in an 8-lead, 3 mm ? 3 mm LFCSP, making it not only a very compact solution, but also providing excellent thermal performance for applications requiring up to 1 A of output current in a small, low profile footprint.Applications Regulation to noise sensitive applications: ADC and DAC circuits, precision amplifiers, PLLs/VCOs, and clocking ICs Communications and infrastructure Medical and healthcare Industrial and instrumentation

The ADM8611/ADM8612/ADM8613/ADM8614/ADM8615?are voltage supervisory circuits that monitor power supply voltage levels and code execution integrity in microprocessor-based systems. Apart from providing power-on reset signals, an on-chip watchdog timer can reset the microprocessor if it fails to strobe within a preset timeout period. A reset signal can also be asserted by an external push-button through a manual reset input.The ultralow power consumption of these devices makes them suitable for power efficiency sensitive systems, such as battery-powered portable devices and energy meters.The features of each member of the device family are shown in Table 9 in the data sheet. Each device subdivides into submodels with differences in factory preset voltage monitoring threshold options. In the range of 2 V to 4.63 V, 10 options are available for the ADM8611. In the range of 2.32 V to 4.63 V, five options are available for both the ADM8613 and ADM8614. A separate supply input allows the ADM8612 and ADM8615 to monitor 20 different low voltage levels from 0.5 V to 1.9 V. Not all device options are available as standard models.The ADM8611, ADM8612, ADM8613, and ADM8615 can reset on demand through the manual reset input. The watchdog function on the ADM8613, ADM8614, and ADM8615 monitors the heartbeat of the microprocessor through the WDI pin. The ADM8613 and ADM8614 have a watchdog disable input, which allows the user to disable the watchdog function, if required. The ADM8614 also has a watchdog timeout extension input, allowing the watchdog timeout to be extended from 1.6 sec to 100 sec.The ADM8611/ADM8612/ADM8613/ADM8614/ADM8615 are available in a 6-ball, 1.46 mm ? 0.96 mm WLCSP. These devices are specified over the temperature range of ?40?C to +85?C.??Applications Portable/battery-operated equipment Microprocessor systems Energy metering Energy harvesting

The ADMV1010 is a compact, gallium arsenide (GaAs) design, monolithic microwave integrated circuit (MMIC), I/Q downconverter in a RoHS compliant package optimized for point to point microwave radio designs that operates in the 12.6 GHz to 15.4 GHz frequency range. The ADMV1010 is optimized to work as a low noise, upper sideband (low side local oscillator (LO)), image reject downconverter.The ADMV1010 provides 15 dB of conversion gain with 25 dB of image rejection. The ADMV1010 uses a radio frequency (RF), low noise amplifier (LNA) followed by an in-phase/quadrature (I/Q) double balanced mixer, where a driver amplifier drives the LO. IF1 and IF2 mixer outputs are provided, and an external 90? hybrid is needed to select the required sideband. The I/Q mixer topology reduces the need for filtering the unwanted sideband. The ADMV1010 is a much smaller alternative to hybrid style SSB downconverter assemblies, and it eliminates the need for wire bonding by allowing the use of surface-mount manufacturing assemblies.The ADMV1010 downconverter comes in a compact, thermally enhanced, 4.9 mm ? 4.9 mm, 32-terminal LCC package. The ADMV1010 operates over the ?40?C to +85?C temperature range.Applications Point to point microwave radios Radars and electronic warfare systems Instrumentation and automatic test equipment Satellite communications

The ADMV1011 is a compact, gallium arsenide (GaAs) design,monolithic microwave integrated circuit (MMIC), doublesideband (DSB) upconverter in a RoHS compliant packageoptimized for point to point microwave radio designs thatoperates in the 17 GHz to 24 GHz frequency range.The ADMV1011 provides 21 dB of conversion gain with 32 dBcof sideband rejection for the lower sideband and 23 dBc ofsideband rejection for the upper sideband. The ADMV1011uses a radio frequency (RF) amplifier preceded by an inphase/quadrature (I/Q) double balanced mixer, where a driveramplifier drives the local oscillator (LO) with a 2? multiplier.IF1 and IF2 mixer inputs are provided and an external 90?hybrid is needed to select the required sideband. The I/Q mixertopology reduces the need for filtering the unwanted sideband.The ADMV1011 is a much smaller alternative to hybrid styleDSB upconverter assemblies and it eliminates the need for wirebonding by allowing the use of surface-mount manufacturingassemblies.The ADMV1011 upconverter comes in a compact, thermallyenhanced, 4.9 mm ? 4.9 mm LCC package. The ADMV1011operates over the ?40?C to +85?C temperature range.Applications Point to point microwave radios Radars and electronic warfare systems Instrumentation, automatic test equipment