TS3A227E evaluation module

The ADM3061E/ADM3062E/ADM3063E/ADM3064E/ADM3065E/ADM3066E/ADM3067E/ADM3068E are 3.0 V to5.5 V, IEC electrostatic discharge (ESD) protected RS-485transceivers, allowing the devices to withstand ?12 kV contactdischarges on the transceiver bus pins without latch-up ordamage. The ADM3062E/ADM3064E/ADM3066E/ADM3068Efeature a VIO logic supply pin that allows a flexible digital interfacecapable of operating as low as 1.62 V. The ADM3065E/ADM3066E/ADM3067E/ADM3068E aresuitable for high speed, 50 Mbps, bidirectional data communication on multipoint bus transmission lines. The ADM3061E/ADM3062E/ADM3063E/ADM3064E/ADM3065E/ADM3066E/ADM3067E/ADM3068E feature a 1/4 unit load inputimpedance that allows up to 128 transceivers on a bus. TheADM3061E/ADM3062E/ADM3063E/ADM3064E models offerall of the same features as the ADM3065E/ADM3066E/ADM3067E/ADM3068E models at a low 500 kbps data rate thatis suitable for operation over long cable runs. The ADM3061E/ADM3062E/ADM3065E/ADM3066E are halfduplex RS-485 transceivers, fully compliant to the PROFIBUS?standard with increased 2.1 V bus differential voltage at VCC ?4.5 V. The ADM3063E/ADM3064E/ADM3067E/ADM3068Eare full duplex RS-485 transceiver options. The RS-485 transceivers are available in a number of spacesaving packages, including the 10-lead, 3 mm ? 3 mm lead framechip-scale package (LFCSP), the 8-lead or 10-lead, 3 mm ? 3 mmmini small outline package (MSOP), and the 8-lead or 14-lead,narrow body standard small outline packages (SOIC_N).Models with operating temperature ranges of ?40?C to +125?Cand ?40?C to +85?C are available. Excessive power dissipation caused by bus contention or byoutput shorting is prevented by a thermal shutdown circuit. If asignificant temperature increase is detected in the internal drivercircuitry during fault conditions, this feature forces the driveroutput into a high impedance state. The ADM3061E/ADM3062E/ADM3063E/ADM3064E/ADM3065E/ADM3066E/ADM3067E/ADM3068E guarantee alogic high receiver output when the receiver inputs are shorted,open, or connected to a terminated transmission line with alldrivers disabled. Table 2 in the data sheet presents an overview of the ADM3061E/ADM3062E/ADM3063E/ADM3064E/ADM3065E/ADM3066E/ADM3067E/ADM3068E data rate capability across temperature, power supply,and package options. Refer to the Ordering Guide section formodel numbering.APPLICATIONS Industrial fieldbuses Process control Building automation PROFIBUS networks Motor control servo drives and encoders?

DLP LightCrafter Display 2010 is an easy to use, plug and play evaluation platform for the DLP2010 chipset, which includes the DLP2010 ( .2 WVGA) DMD, DLPC3435 display controller and DLPA2005 PMIC/LED driver. This EVM comes equipped with an optical engine that enables quick evaluation of the DLP2010 chipset for ultra-mobile and ultra-low power display applications. Its modular design allows the exchange of multiple light engines to fit diverse equipment design needs.

Two versions of the evaluation module are available:

1. DLPDLCR2010EVM: Full-featured version that includes boards, optical engine, DMD, flex and LED cables

2. DLPDLCR2010EVM-PCB: Includes the PCB main and display boards only (does not include optical engine, DMD, flex or LED cables)

Features:

• EVM compatible with wide range of optical modules
• Standard HDMI-input interface offers plug-and-play functionality with various devices.
• Get started quickly with simple yet powerful USB-based GUI
• Comes powered with IntelliBright suite of image processing algorithm to dynamically optimize system brightness or power

What's included:

 

• DLP2010, DLP 0.2 WVGA DMD
• DLPC3435, Digital Controller for the DLP2010 DMD
• DLPA2005, PMIC/LED Driver for the DLP2010 DMD and DLPC3435 controller
• Optical engine from Asia Optical
• DLP2010, DLPC3435 Configuration and Support Firmware
• 1 HDMI cable
• 1 USB Cable ( for communication with USB based GUI tool)
• Power supply sold separately.

 

Interface Development Tools PTN38007-EVM

PCA9957 LED Driver Power Management Arduino Platform Evaluation Expansion Board

TLS850B0TBV33 OPTIREG™ 1 - Single Channels per IC Positive Fixed Linear Voltage Regulator Evaluation Board

The ADAU1777 is a codec with four inputs and two outputs thatincorporates a digital processing engine to perform filtering,level control, signal level monitoring, and mixing. The pathfrom the analog input to the DSP core to the analog output isoptimized for low latency and is ideal for noise canceling headsets.With the addition of just a few passive components, a crystal,and an EEPROM for booting, the ADAU1777 provides a completeheadset solution.Note that throughout this data sheet, multifunction pins, such asSCL/SCLK, are referred to either by the entire pin name or by asingle function of the pin, for example, SCLK, when only thatfunction is relevant.Applications Noise canceling handsets, headsets, and headphones Bluetooth??active noise cancelling (ANC) handsets, headsets, and headphones Personal navigation devices Digital still and video cameras

ADS5281 Eight-Channel; 12-Bit; 50-MSPS Analog-to-Digital Converter Evaluation Board

The LT1934 is a micropower step-down DC/DC converter with internal 400mA power switch, packaged in a low profile (1mm) ThinSOT. With its wide input range of 3.2V to 34V, the LT1934 can regulate a wide variety of power sources, from 4-cell alkaline batteries and 5V logic rails to unregulated wall transformers and lead-acid batteries. Quiescent current is just 12?A and a zero current shutdown mode disconnects the load from the input source, simplifying power management in battery-powered systems. Burst Mode? operation and the low drop internal power switch result in high efficiency over a broad range of load current.The LT1934 provides up to 300mA of output current. The LT1934-1 has a lower current limit, allowing optimum choice of external components when the required output current is less than 60mA. Fast current limiting protects the LT1934 and external components against shorted outputs, even at 34V input.Applications Wall Transformer Regulation Automotive Battery Regulation Standby Power for Portable Products Distributed Supply Regulation Industrial Control Supplies

Demonstration circuit 1091 is a monolithic step-down switching regulator featuring the LT3480 in the MSOP-10 exposed pad package. The operating frequency can be synchronized up to 2MHz. The demo board is designed for 5V/2A output from a 6.3V to 38V input with transients up to 60V. The wide input range of the LT3480 allows a variety of input sources. The typical sources are automotive batteries, wall adaptors and industrial supplies. The modes of operation (Burst Mode and fixed frequency) are jumper selectable.