Replicator for MSP430 MCU

The AD7770 is an 8-channel, simultaneous sampling ADC. Eightfull sigma-delta (?-?) ADCs are on chip. The AD7770 providesa low input current to allow direct sensor connection. Each inputchannel has a programmable gain stage allowing gains of 1, 2, 4,and 8 to map lower amplitude sensor outputs into the full-scaleADC input range, maximizing the dynamic range of the signalchain. The AD7770 accepts a VREF voltage from 1 V up to 3.6 V.The analog inputs accept unipolar (0 V to VREF) or true bipolar(?VREF/2) analog input signals with 3.3 V or ?1.65 V analogsupply voltages, respectively for PGAGAIN = 1. The analog inputscan be configured to accept true differential, pseudo differential,or single-ended signals to match different sensor outputconfigurations.Each channel contains a PGA, an ADC modulator and asinc3, low latency digital filter. An SRC is provided to allow fineresolution control over the AD7770 ODR. This control can beused in applications where the ODR resolution is required tomaintain coherency with 0.01 Hz changes in the line frequency.The SRC is programmable through the serial port interface (SPI).The AD7770 implements two different interfaces: a data outputinterface and SPI control interface. The ADC data output interfaceis dedicated to transmitting the ADC conversion results fromthe AD7770 to the processor. The SPI writes to and reads fromthe AD7770 configuration registers and for the control andreading of data from the SAR ADC. The SPI can also beconfigured to output the ?-? conversion data.The AD7770 includes a 12-bit SAR ADC. This ADC can beused for AD7770 diagnostics without having to decommissionone of the ?-? ADC channels dedicated to system measurementfunctions. With the use of an external multiplexer, which can becontrolled through the three general-purpose input/output pins(GPIOs), and signal conditioning, the SAR ADC can validatethe ?-? ADC measurements in applications where functionalsafety is required. In addition, the AD7770 SAR ADC includesan internal multiplexer to sense internal nodes.The AD7770 contains a 2.5 V reference and reference buffer. Thereference has a typical temperature coefficient of 10 ppm/?C.The AD7770 offers two modes of operation: high resolution modeand low power mode. High resolution mode provides a higherdynamic range while consuming 10.75 mW per channel; lowpower mode consumes just 3.37 mW per channel at a reduceddynamic range specification.The specified operating temperature range is ?40?C to +105?C,although the device is operational up to +125?C.Applications Protection relays General-purpose data acquisition Industrial process control

DAC8411 Performance Demonstration Kit

LMR16006XEVM 6V to 60V input; 5.0V output at 600mA Step-Down Converter

The HMC534LP5(E) is a GaAs InGaP Heterojunction Bipolar Transistor (HBT) MMIC VCO. The HMC534LP5(E) integrates resonators, negative resistance devices, varactor diodes and feature half frequency and divide-by-4 outputs. The VCO?s phase noise performance is excellent over temperature, shock, and process due to the oscillator?s monolithic structure. Power output is +11 dBm typical from a +5V supply voltage. The prescaler and RF/2 functions can be disabled to conserve current if not required. The voltage controlled oscillator is packaged in a leadless QFN 5x5 mm surface mount package, and requires no external matching components.APPLICATIONS Point-to-Point/Multi-point Radio Test Equipment & Industrial Controls SATCOM Military End-Use

TAS5715EVM Evaluation Module

WLED Drivers For Smart Phone Evaluation Module

The LTC7001 is a fast high side N-channel MOSFET gate driver that operates from input voltages up to 135V. It contains an internal charge pump that fully enhances an external N-channel MOSFET switch, allowing it to remain on indefinitely.Its powerful driver can easily drive large gate capacitances with very short transition times, making it well suited for both high frequency switching applications or static switch applications that require a fast turn-on and/or turn-off time.The LTC7001 is available in the thermally enhanced 10-lead MSOP package.APPLICATIONS Static Switch Driver Load and Supply Switch Driver Electronic Valve Driver High Frequency High Side Gate Driver

The ?ADA4433-1 is a differential output, fully integrated video reconstruction filter that combines overvoltage protection (short-to-battery [STB] protection) and short-to-ground (STG) protection on the outputs, with excellent video specifications and low power consumption. The combination of STB protection and robust ESD tolerance allows the ADA4433-1 to provide superior protection in the hostile automotive environment.The ADA4433-1 is a fully differential video filter that can be used as a fully differential input to a differential output or as a single-ended input to a differential output, allowing it to easily connect to both differential and single-ended sources. It is capable of driving twisted pair or coaxial cable with minimal line attenuation. Differential signal processing reduces the effects of ground noise, which can plague ground referenced systems. The ADA4433-1 is ideal for differential signal processing (gain and filtering) throughout the signal chain, simplifying the conversion between single-ended and differential components.The short-to-battery protection integrated into the ADA4433-1 protects against both dc and transient overvoltage events, caused by an accidental short to a battery voltage up to 18 V. The Analog Devices, Inc., short-to-battery protection eliminates the need for large output coupling capacitors and other complicated circuits used to protect standard video amplifiers, saving space and cost.The ADA4433-1 features a high-order filter with ?3 dB cutoff frequency response at 10 MHz and 45 dB of rejection at 27 MHz. The ADA4433-1 featurea an internally fixed gain of 2 V/V. This makes the ADA4433-1 ideal for SD video applications, including NTSC and PAL.The ADA4433-1 operates on single supplies as low as 2.6 V and as high as 3.6 V while providing the dynamic range required by the most demanding video systems.The ADA4433-1 is offered in an 8-lead, 3 mm ? 3 mm LFCSP package, rated for operation over the wide automotive temperature range of ?40?C to +125?C.Appplications Automotive rearview cameras Automotive video electronic control units (ECUs) Surveillance video systems

Acceleration Sensor Development Tools iNemo inertial module kit based on IIS3DWB