The LTM8051 is quad 40VIN, 1.2A step-down Silent Switcher ?Module? regulator. The Silent Switcher architecture minimizes EMI while delivering high efficiency at frequencies up to 3MHz. Included in the package are the controllers, power switches, inductors, and support components. Operating over a wide input voltage range, the LTM8051 supports output voltages from 0.8V to 8V, and a switching frequency range of 300kHz to 3MHz, each set by a single resistor. Only the bulk input and output filter capacitors are needed to finish the design. The LTM8051 product video?is available on website. The LTM8051 is packaged in a compact (6.25mm ? 11.25mm ? 2.22mm) over-molded Ball Grid Array (BGA) package suitable for automated assembly by standard surface mount equipment. The LTM8051 is available with SnPb (BGA) or RoHS compliant.APPLICATIONS Automated Test Equipment Distributed Supply Regulation Industrial Supplies Medical Equipment

Demonstration circuit 2866A features the LTC4421 Dual Supply High Power Prioritized Powerpath™ Controller in a 12V/24V, 10A application. The LTC4421 incorporates strong gate drivers to switch large external N-channel MOSFETs and fast switchover circuitry to minimize VOUT droop while preventing reverse and cross conduction currents, making it an ideal solution for high reliability systems, battery back up systems, and servers. DC2866A arbitrates between two input supply rails, selecting the highest priority, valid supply to power the load. By definition, the supply connected to V1 is the higher priority supply, although it can be changed dynamically. External resistive dividers set the undervoltage and overvoltage thresholds that bound the valid voltage window. External sense resistors set the limit on maximum current that can flow to the load. Two or more DC2866As can be cascaded to provide switchover between more than two rails.

The HMC322ALP4E is a broadband non-reflective GaAs MESFET SP8T switch in a low cost leadless surface mount package. Covering DC to 8 GHz, this switch offers high isolation and low insertion loss. This switch also includes an on board binary decoder circuit which reduces the required logic control lines to three. The switch operates using a negative control voltage of 0/-5 volts, and requires a fixed bias of -5V. This switch is suitable for usage in 50-Ohm or 75-Ohm systems.ApplicationsThis switch is suitable for usage in DC - 8.0 GHz 50-Ohm or 75-Ohm systems: Broadband Fiber Optics Switched Filter Banks Wireless below 8 GHz

The HMC427ALP3E is a low loss broadband positive control transfer switch in leadless surface mount package. Covering DC to 8 GHz, this switch offers high isolation and low insertion loss. The switch operates using a positive control voltage of 0/+5V and requires a fixed bias of +5V at < 20 ?A.Applications Test Instrumentation Fiber Optics & Broadband Telecom Basestation Infrastructure Microwave Radio & VSAT Military Radios, Radar, & ECM

The HMC589AST89E is an InGaP HBT Gain Block MMIC SMT amplifier covering DC to 4 GHz and packaged in an industry standard SOT89E. The amplifier can be used as a cascadable 50 Ohm RF or IF gain stage as well as a LO or PA driver with up to +19 dBm P1dB output power for cellular/3G, FWA, CATV, microwave radio and test equipment applications. The HMC589AST89E offers 20 dB gain and +33 dBm output IP3 at 1 GHz while requiring only 82 mA from a single positive supply. The HMC589AST89E InGaP HBT gain block offers excellent output power and gain stability over temperature.APPLICATIONSCellular / PCS / 3GFixed Wireless & WLANCATV, Cable Modem & DBSMicrowave Radio & Test EquipmentIF & RF Applications

The HMC712ALP3CE is an absorptive Voltage Variable Attenuator (VVA) which operates from 5 - 26.5 GHz and is ideal in designs where an analog DC control signal must be used to control RF signal levels over a 28 dB amplitude range. It features two shunt-type attenuators which are controlled by two analog voltages, Vctrl1 and Vctrl2. Optimum linearity performance of the attenuator is achieved by first varying Vctrl1 of the 1st attenuation stage from -5V to 0V with Vctrl2 fixed at -5V. The control voltage of the 2nd attenuation stage, Vctrl2, should then be varied from -5V to 0V, with Vctrl1 fixed at 0V. The HMC712ALP3CE is housed in a RoHS compliant 3x3 mm QFN leadless package.Furthermore, if the Vctrl1 and Vctrl2 pins are connected together it is possible to achieve the full analog attenuation range with only a small degradation in input IP3 performance. Applications include AGC circuits and temperature compensation of multiple gain stages in microwave point-to-point and VSAT radios.Applications Point-to-Point Radio VSAT Radio Test Instrumentation Microwave Sensors Military, ECM & Radar

The HMC717ALP3E is a GaAs PHEMT MMICLow Noise Amplifier that is ideal for fixed wirelessand LTE/WiMAX/4G basestation front-end receiversoperating between 4.8 and 6.0 GHz. The amplifierhas been optimized to provide 1.1 dB noise figure,14.5 dB gain and +29.5 dBm output IP3 from a singlesupply of +5V. Input and output return losses areexcellent and the LNA requires minimal externalmatching and bias decoupling components. TheHMC717ALP3E can be biased with +3V to +5V andfeatures an externally adjustable supply currentwhich allows the designer to tailor the linearityperformance of the LNA for each application.Applications Fixed wireless and LTE/WiMAX/4G BTS and infrastructure Repeaters and Femtocells Public safety radio Access points

The HMC773ALC3B is a general-purpose, double balanced mixer ina leadless, RoHS compliant LCC package that can be used as anupconverter or downconverter from 6 GHz to 26 GHz. Thismixer requires no external components or matching circuitry. The HMC773ALC3B provides excellent LO to RF and LO to IFsuppression due to optimized balun structures. The mixeroperates well with LO drive levels of 13 dBm or above. TheHMC773ALC3B eliminates the need for wire bonding, allowing useof surface-mount manufacturing techniques.Applications Point to point radios Point to multipoint radios and very small aperture terminals (VSATs) Test equipment and sensors Military end use

The HMC7992 is a general-purpose, nonreflective, 0.1 GHz to 6.0 GHz, silicon, single-pole, four-throw (SP4T) switch in aleadless, surface-mount package. The switch is ideal for cellular infrastructure applications, offers high isolation of 45 dB typical at 2 GHz, and a low insertion loss of 0.6 dB at 2 GHz. It offers excellent power handling capability up to 6.0 GHz, with inputpower of 1 dB compression point (P1dB) of 35 dBm at 5 V operation. The HMC7992 has good low frequency input power handling below 0.1 GHz and can operate well down to 10 kHz, with a typical 1 dB compression of 21 dBm and an IIP3 of 37 dBm at 1 MHz.The on-chip circuitry allows the HMC7992 to operate at a single, positive supply voltage range from 3.3 V to 5 V, and as well as a single, positive control voltage from 0 V to 1.8 V/3.3 V/5.0 V. A 2:4 decoder integrated in the switch requires only two controlled input signals, with a positive control voltage range from 0 V to 1.8 V/3.3 V/5.0 V, to select one of the four radio frequency (RF)paths.Applications Cellular/4G infrastructure Wireless infrastructure Automotive telematics Mobile radios Test equipment

The HMC8342 is a gallium arsenide (GaAs), monolithic microware integrated circuit (MMIC), ?2 active broadband frequency multiplier. When driven by a 5 dBm signal, the multiplier provides 15 dBm typical output power. The output frequency range is from 22 GHz to 42 GHz, and the input fundamental and third harmonic isolations measured at the output are ?23 dBc and ?20 dBc, respectively, at an output frequency of 30 GHz. The HMC8342 is ideal for use in LO multiplier chains for point to point and VSAT radios, resulting in a reduced parts count vs. traditional design approaches.APPLICATIONSClock generationPoint to point and very small aperture terminal (VSAT) radiosTest instrumentationMilitary and space