The AD7441 / AD7451 are, respectively, 10-/12-bit high speed, low power, single-supply, successive approximation (SAR), analog-to-digital converters (ADCs) that feature a pseudo differential analog input. These parts operate from a single 2.7 V to 5.25 V power supply and achieve very low power dissipation at high throughput rates of up to 1 MSPS.The AD7441 / AD7451 contain a low noise, wide bandwidth, differential track-and-hold (T/H) amplifier that handles input frequencies up to 3.5 MHz. The reference voltage for these devices is applied externally to the VREF pin and can range from 100 mV to VDD, depending on the power supply and what suits the application.The conversion process and data acquisition are controlled using overbar: CS and the serial clock, allowing the device to interface with microprocessors or DSPs. The input signals are sampled on the falling edge of overbar: CS when the conversion is initiated. The SAR architecture of these parts ensures that there are no pipeline delays.PRODUCT HIGHLIGHTS Operation with 2.7 V to 5.25 V Power Supplies. High Throughput with Low Power Consumption. With a 3 V supply, the AD7441 / AD7451 offer 4 mW maxi-mum power consumption for a 1 MSPS throughput rate. Pseudo Differential Analog Input. Flexible Power/Serial Clock Speed Management. The conversion rate is determined by the serial clock, allowing the power to be reduced as the conversion time is reduced through the serial clock speed increase. These parts also feature a shutdown mode to maximize power efficiency at lower throughput rates. Variable Voltage Reference Input. No Pipeline Delays. Accurate Control of Sampling Instant via overbar: CS Input and Once-Off Conversion Control. ENOB > 10 Bits Typically with 500 mV Reference.APPLICATIONS Transducer interface Battery-powered systems Data acquisition systems Portable instrumentation

The AD5337 / AD5338 / AD5339 are dual 8-, 10-, and 12-bit buffered voltage output DACs, respectively. Each part is housed in an 8-lead MSOP package and operates from a single 2.5 V to 5.5 V supply, consuming 250 μA at 3 V. On-chip output amplifiers allow rail-to-rail output swing with a slew rate of 0.7 V/μs. A 2-wire serial interface operates at clock rates up to 400 kHz. This interface is SMBus compatible at VDD < 3.6 V. Multiple devices can be placed on the same bus.The references for the two DACs are derived from one reference pin. The outputs of all DACs can be updated simultaneously using the software LDAC function. The parts incorporate a power-on reset circuit to ensure that the DAC outputs power up to 0 V and remain there until a valid write to the device takes place. A software clear function resets all input and DAC registers to 0 V. A power-down feature reduces the current consumption of the devices to 200 nA @ 5 V (80 nA @ 3 V).The low power consumption of these parts in normal operation makes them ideally suited to portable battery-operated equipment. The power consumption is typically 1.5 mW at 5 V and 0.75 mW at 3 V, reducing to 1 μW in power-down mode.APPLICATIONS Portable battery-powered instruments Digital gain and offset adjustment Programmable voltage and current sources Programmable attenuators Industrial process control

Dual, 0.2 V/C Offset Drift, 105 MHz Low Power, Low Noise, Rail-to-Rail Amplifier Features: Low input offset voltage: 125 µV (maximum) Low input offset voltage drift 0.2 µV/°C (typical) 1.5 µV/°C (maximum) Ultralow supply current: 500 µA per amplifier Fully specified at VS = 3 V, 5 V, ±5 V High speed performance −3 dB bandwidth: 105 MHz Slew rate: 160 V/µs Settling time to 0.1%: 35 ns Rail-to-rail outputs See data sheet for additional featuresADA4805-2-EP supports defense and aerospace applications (AQEC standard) Download the ADA4805-2-EP data sheet (pdf) Extended industrial temperature range (−55°C to +125°C) Controlled manufacturing baseline 1 assembly/test site 1 fabrication site Enhanced product change notification Qualification data available upon request V62/16621 DSCC Drawing Number

Pushbutton Switch SPDT Standard, Illuminated Panel Mount, Front

Pushbutton Switch SPDT Standard, Illuminated Panel Mount, Front

OP-AMP, 10.4MHZ, 6 TO 40V, MSOP-8;

Non-Penetrating Antenna Flat Roof Mount 34-Inch Pole Only |Fairview Microwave FMFRMARM

LAPTOP TRAY, VESA MOUNT, 75X75/100X100;

Filter/Autoranging Rectifier Module 90V to 132V/180V to 264V 250V to 370V Through Hole 9-Pin Half Brick

Filter/Autoranging Rectifier Module 90V to 132V/180V to 264V 250V to 370V Screw Mount 9-Pin Half Brick