The AD8223 is an integrated single-supply instrumentationamplifier that delivers rail-to-rail output swing on a singlesupply (3 V to 24 V). The AD8223 conforms to the 8-leadindustry standard pinout configurationThe AD8223 is simple to use: one resistor sets the gain. With no external resistor, the AD8223 is configured for G = 5 and with an external resistor, the AD8223 can be programmed for gains up to 1000.The AD8223 has a wide input common-mode range and canamplify signals that have a 150 mV common-mode voltagebelow ground. Although the design of the AD8223 is optimizedto operate from a single supply, the AD8223 still providesexcellent performance when operated from a dual voltagesupply (±2 V to ±12 V).Low power consumption (1.5 mW at 3 V), wide supply voltagerange, and rail-to-rail output swing make the AD8223 ideal forbattery-powered applications. The rail-to-rail output stagemaximizes the dynamic range when operating from low supplyvoltages. The AD8223 replaces discrete instrumentationamplifier designs and offers superior linearity, temperaturestability, and reliability in a minimum of space.ApplicationsLow power medical instrumentation Transducer interface Thermocouple amplifiers Industrial process controls Difference amplifiers Low power data acquisition

The AD8226 is a low cost, wide supply range instrumentation amplifier that requires only one external resistor to set any gain between 1 and 1000.The AD8226 is designed to work with a variety of signal voltages. A wide input range and rail-to-rail output allow the signal to make full use of the supply rails. Because the input range also includes the ability to go below the negative supply, small signals near ground can be amplified without requiring dual supplies. The AD8226 operates on supplies ranging from ±1.35 V to ±18 V for dual supplies and 2.2 V to 36 V for single supply.The robust AD8226 inputs are designed to connect to real-world sensors. In addition to its wide operating range, the AD8226 can handle voltages beyond the rails. For example, with a ±5 V supply, the part is guaranteed to withstand ±35 V at the input with no damage. Minimum as well as maximum input bias currents are specified to facilitate open wire detection.The AD8226 is perfect for multichannel, space-constrained industrial applications. Unlike other low cost, low power instrumentation amplifiers, the AD8226 is designed with a minimum gain of 1 and can easily handle ±10 V signals. With its MSOP package and 125°C temperature rating, the AD8226 thrives in tightly packed, zero airflow designs.The AD8226 is available in 8-lead MSOP and SOIC packages, and is fully specified for −40°C to +125°C operation.For a device with a similar package and performance as the AD8226 but with gain settable from 5 to 1000, consider using the AD8227.ApplicationsIndustrial process controlsBridge amplifiersMedical instrumentationPortable data acquisitionMultichannel systems

The AD8274 is a difference amplifier that delivers excellent ac and dc performance. Built on Analog Devices, Inc., proprietary iPolar® process and laser-trimmed resistors, AD8274 achieves a breakthrough in distortion vs. current consumption and has excellent gain drift, gain accuracy, and CMRR.Distortion in the audio band is an extremely low 0.00025% (112 dB) at a gain of ½ and 0.00035% (109 dB) at a gain of 2 while driving a 600 Ω load.With supply voltages up to ±18 V (+36 V single supply), the AD8274 is well suited for measuring large industrial signals. Additionally, the part’s resistor divider architecture allows it to measure voltages beyond the supplies.With no external components, the AD8274 can be configured as a G = ½ or G = 2 difference amplifier. For single-ended applications that need high gain stability or low distortion performance, the AD8274 can also be configured for several gains ranging from −2 to +3.The excellent distortion and dc performance of the AD8274, along with its high slew rate and bandwidth, make it an excellent ADC driver. Because of the part’s high output drive, it also makes a very good cable driver.The AD8274 only requires 2.6 mA maximum supply current. It is specified over the industrial temperature range of −40°C to +85°C and is fully RoHS compliant. For the dual version, see the AD8273 data sheet.Applications ADC driver High performance audio Instrumentation amplifier building blocks Level translators Automatic test equipment Sine/cosine encoders

The AD8275 is a G=0.2 difference amplifier that can be used totranslate +/-10V signals to a +4V level. It solves the problemtypically encountered in industrial and instrumentation where+/-10V signals must be interfaced to a single supply 4V or 5VADC. The AD8275 interfaces the two signal levels, simplifyingdesign.The AD8275 has fast settling time of 450 ns and low distortion,making it suitable for driving medium speed successive approximation(SAR) ADCs. Its wide input voltage range and rail-torailoutputs make it an easy to use building block. Single-supplyoperation reduces the power consumption of the amplifier andhelps to protect the ADC from overdrive conditions. Internal, matched, precision laser-trimmed resistors ensurelow gain error, low gain drift of 1 ppm/°C (maximum), andhigh common-mode rejection of 80 dB. Low offset and lowoffset drift, combined with its fast settling time, make theAD8275 suitable for a variety of data acquisition applicationswhere accurate and quick capture is required. The AD8275 can be used as an analog front end, or it can followbuffers to level translate high voltages to a voltage range acceptedby the ADC. In addition, the AD8275 can be configured fordifferential outputs if used with a differential ADC. The AD8275 is available in a space-saving, 8-lead MSOP and is specified for performance over the −40°C to +85°C temperature range.ApplicationsLevel TranslatorADC DriverInstrumentation Amplifier Building BlockAutomated test equipment

The AD8646 and the AD8647 are the dual, and the AD8648 isthe quad, rail-to-rail, input and output, single-supply amplifiersfeaturing low offset voltage, wide signal bandwidth, low inputvoltage, and low current noise. The AD8647 also has a lowpower shutdown function.The combination of 24 MHz bandwidth, low offset, low noise,and very low input bias current makes these amplifiers useful ina wide variety of applications. Filters, integrators, photodiodeamplifiers, and high impedance sensors all benefit from thecombination of performance features. AC applications benefitfrom the wide bandwidth and low distortion. The AD8646/AD8647/AD8648 offer high output drive capability, which isexcellent for audio line drivers and other low impedanceapplications. The AD8646 and AD8648 are available forautomotive applications (see the Ordering Guide).Applications include portable and low powered instrumentation,audio amplification for portable devices, portable phoneheadsets, barcode scanners, and multipole filters. The ability toswing rail to rail at both the input and output enables designersto buffer CMOS ADCs, DACs, ASICs, and other wide outputswing devices in single-supply systems.Applications Battery-powered instruments Multipole filters ADC front ends Sensors Barcode scanners ASIC input or output amplifiers Audio amplifiers Photodiode amplifiers Datapath/mux/switch control

The ADM705 / ADM706 / ADM707 / ADM708 microprocessorsupervisory circuits are suitable for monitoring 5 V powersupplies/batteries and microprocessor activity.The ADM705 / ADM706 provide power-supply monitoringcircuitry that generate a reset output during power-up, powerdown,and brownout conditions. The reset output remainsoperational with VCC as low as 1 V. Independent watchdogmonitoring circuitry is also provided. This is activated if thewatchdog input has not been toggled within 1.60 sec.In addition, there is a 1.25 V threshold detector to warn ofpower failures, to detect low battery conditions, or to monitor anadditional power supply. An active low, debounced manual resetinput (MR) is also included.The ADM705 and ADM706 are identical except for the resetthreshold monitor levels, which are 4.65 V and 4.40 V, respectively.The ADM707 and ADM708 provide a similar functionality tothe ADM705 and ADM706 and only differ in that a watchdogtimer function is not available. Instead, an active high resetoutput (RESET) is available as well as the active low reset output(RESET). The ADM707 and ADM708 are identical except forthe reset threshold monitor levels, which are 4.65 V and 4.40 V,respectively.All devices are available in narrow 8-lead PDIP and 8-lead SOICpackages.APPLICATIONS Microprocessor systems Computers Controllers Intelligent instruments Critical microprocessor supply monitoring

The ADR430/ADR431/ADR433/ADR434/ADR435 series is a family of XFET® voltage references featuring low noise, high accuracy, and low temperature drift performance. Using Analog Devices, Inc., temperature drift curvature correction and extra implanted junction FET (XFET) technology, voltage change vs. temperature nonlinearity in the ADR430/ADR431/ADR433/ADR434/ADR435 is minimized.The XFET references operate at lower current (800 μA) and lower supply voltage headroom (2 V) than buried Zener references. Buried Zener references require more than 5 V of headroom for operation. The ADR430/ADR431/ADR433/ADR434/ADR435 XFET references are low noise solutions for 5 V systems.The ADR430/ADR431/ADR433/ADR434/ADR435 family has the capability to source up to 30 mA of output current and sink up to −20 mA. It also comes with a trim terminal to adjust the output voltage over a ±0.5% range without compromising performance.The ADR430/ADR431/ADR433/ADR434/ADR435 are available in 8-lead MSOP and 8-lead narrow SOIC packages. All versions are specified over the extended industrial temperature range of −40°C to +125°C.Applications Precision data acquisition systems High resolution data converters Medical instruments Industrial process control systems Optical control circuits Precision instruments

The ADT75 is a complete temperature monitoring system in 8-lead MSOP and SOIC packages. It contains a band gap temperature sensor and 12-bit Aanalog-to-digital converter (ADC) to monitor and digitize the temperature to a resolution of 0.0625°C. The ADT75 is pin and register compatible with the LM75 and AD7416.The ADT75 is specified for operation at supply voltages from 2.7 V to 5.5 V. Operating at 3.3 V, the average supply current is typically 200 μA.The ADT75 offers a shutdown mode that powers down the device and this mode gives a shutdown current of typically 3 μA. The ADT75 is rated for operation over the –55°C to +125°C temperature range.The A0, A1, and A2 pins are available for address selection. The OS/ALERT pin is an open-drain output that becomes active when temperature exceeds a programmable limit. The OS/ALERT pin can operate in either comparator or interrupt mode.Product Highlights On-chip temperature sensor allows an accurate measurement of the ambient temperature. The measurable temperature range is −55°C to +125°C. Supply voltage is 2.7 V to 5.5 V. Space-saving, 8-lead MSOP and 8-lead SOIC. Temperature accuracy is ±1°C maximum. Temperature resolution is 0.0625°C. Shutdown mode reduces the current consumption to 3 μA typical. Connect up to eight ADT75s to a single SMBus/I2C bus.Applications Isolated Sensors Environmental Control Systems Computer Thermal Monitoring Thermal Protection Industrial Process Control Power-system Monitors Hand Held Applications

The ADM1485 is a differential line transceiver suitable for high speed bidirectional data communication on multipoint bus transmission lines. It is designed for balanced data transmission and complies with both EIA Standards RS-485 and RS-422. The part contains a differential line driver and a differential line receiver. Both the driver and the receiver may be enabled independently. When disabled, the outputs are tristated.The ADM1485 operates from a single +5 V power supply. Excessive power dissipation caused by bus contention or by output shorting is prevented by a thermal shutdown circuit. This feature forces the driver output into a high impedance state if during fault conditions a significant temperature increase is detected in the internal driver circuitry.Up to 32 transceivers may be connected simultaneously on a bus, but only one driver should be enabled at any time. It is important therefore that the remaining disabled drivers do not load the bus. To ensure this, the ADM1485 driver features high output impedance when disabled and also when powered down.This minimizes the loading effect when the transceiver is not being utilized. The high impedance driver output is maintained over the entire common-mode voltage range from -7 V to +12 V.The receiver contains a fail safe feature which results in a logic high output state if the inputs are unconnected (floating).The ADM1485 is fabricated in BiCMOS, an advanced mixed technology process combining low power CMOS with fast switching bipolar technology. All inputs and outputs contain protection against ESD; all driver outputs feature high source and sink current capability. An epitaxial layer is used to guard against latch-up.The ADM1485 features extremely fast switching speeds. Minimal driver propagation delays permit transmission at data rates up to 30 Mbits/s while low skew minimizes EMI interference.The part is fully specified over the commercial and industrial temperature range and is available in an 8-pin DIL/SOIC package.

The AD8002 is a dual, low power, high speed amplifierdesigned to operate on ±5 V supplies. The AD8002 featuresunique transimpedance linearization circuitry, which allows theAD8002 to drive video loads with excellent differential gainand phase performance on only 50 mW of power per amplifier.The AD8002 is a current feedback amplifier and features gainflatness of 0.1 dB to 60 MHz while offering differential gain andphase error of 0.01% and 0.02°, which makes the AD8002 idealfor professional video electronics such as cameras and videoswitchers. Additionally, the low distortion and fast settling ofthe AD8002 make it ideal for buffer high speed analog-todigitalconverters (ADCs).The AD8002 offers a low power of 5.0 mA/amp maximum(VS = ±5 V) and can run on a single 12 V power supply, yet iscapable of delivering over 70 mA of load current. It is offeredin 8-lead SOIC and MSOP packages. These features make thisamplifier ideal for portable and battery-powered applicationswhere size and power are critical.The bandwidth of 600 MHz along with 1200 V/μs of slew ratemake the AD8002 useful in many general-purpose high speedapplications where dual power supplies of up to ±6 V and singlesupplies from 6 V to 12 V are needed. The AD8002 is availablein the industrial temperature range of −40°C to +85°C.ApplicationsAnalog-to-digital driversVideo line driversDifferential line driversProfessional camerasVideo switchersSpecial effectsRF receivers