DC-DC Converters Efficiency up to 90% / 3 Year Warranty 30-600 Watts Through Hole Mount Input: 18-75 VDC Output: 15.0 V/5.00 A Power: 75 W

Operational Amplifiers - Op Amps Single/Dual/Triple/Quad Operational Amplifiers

Operational Amplifiers - Op Amps Quad CMOS Low Power

Operational Amplifiers - Op Amps Dual CMOS Low Power

2/2 Transceiver Full RS232 16-SOIC

Supervisor Open Drain or Open Collector 2 Channel 8-SOIC

The ICL761X–ICL764X family of monolithic CMOS op amps combine ultra-low input current with low-power operation over a wide supply voltage range. With pinselectable quiescent currents of 10µA, 100µA, or 1000µA per amplifier, these op amps will operate from ±1V to ±8V power supplies, or from single supplies from 2V to 16V. The CMOS outputs swing to within millivolts of the supply voltages.The ultra-low bias current of 1pA makes this family of op amps ideal for long time constant integrators, picoammeters, low droop rate sample/hold amplifiers and other applications where input bias and offset currents are critical. A low noise current of 0.01pA and an input impedance of 1012Ω ensure optimum performance with very high source impedances in such applications as pH meters and photodiode amplifiers.ApplicationsBattery-Powered InstrumentsHearing Aids and Microphone AmplifiersLong-Time Constant IntegratorsLow Droop Rate Sample/Hold AmplifiersLow-Frequency Active FiltersLow-Leakage AmplifiersPicoammeters

The ICL761X–ICL764X family of monolithic CMOS op amps combine ultra-low input current with low-power operation over a wide supply voltage range. With pinselectable quiescent currents of 10µA, 100µA, or 1000µA per amplifier, these op amps will operate from ±1V to ±8V power supplies, or from single supplies from 2V to 16V. The CMOS outputs swing to within millivolts of the supply voltages.The ultra-low bias current of 1pA makes this family of op amps ideal for long time constant integrators, picoammeters, low droop rate sample/hold amplifiers and other applications where input bias and offset currents are critical. A low noise current of 0.01pA and an input impedance of 1012Ω ensure optimum performance with very high source impedances in such applications as pH meters and photodiode amplifiers.ApplicationsBattery-Powered InstrumentsHearing Aids and Microphone AmplifiersLong-Time Constant IntegratorsLow Droop Rate Sample/Hold AmplifiersLow-Frequency Active FiltersLow-Leakage AmplifiersPicoammeters

The ICL7665 warns microprocessors (µPs) of overvoltage and undervoltage conditions. It draws a typical operating current of only 3µA. The trip points and hysteresis of the two voltage detectors are individually programmed via external resistors to any voltage greater than 1.3V. The ICL7665 will operate from any supply voltage in the 1.6V to 16V range, while monitoring voltages from 1.3V to several hundred volts. The Maxim ICL7665A is an improved version with a 2%-accurate VSET1 threshold and guaranteed performance over temperature.The 3µA quiescent current of the ICL7665 makes it ideal for voltage monitoring in battery-powered systems. In both battery- and line-powered systems, the unique combination of a reference, two comparators, and hysteresis outputs reduces the size and component count of many circuits.ApplicationsµP Voltage MonitoringBattery-Backup SwitchingHigh/Low Temperature, Pressure, Voltage AlarmsLow-Battery DetectionOver/Undervoltage ProtectionPower Supply Fault MonitoringPower-Fail and Brownout Detection

The ICL7665 warns microprocessors (µPs) of overvoltage and undervoltage conditions. It draws a typical operating current of only 3µA. The trip points and hysteresis of the two voltage detectors are individually programmed via external resistors to any voltage greater than 1.3V. The ICL7665 will operate from any supply voltage in the 1.6V to 16V range, while monitoring voltages from 1.3V to several hundred volts. The Maxim ICL7665A is an improved version with a 2%-accurate VSET1 threshold and guaranteed performance over temperature.The 3µA quiescent current of the ICL7665 makes it ideal for voltage monitoring in battery-powered systems. In both battery- and line-powered systems, the unique combination of a reference, two comparators, and hysteresis outputs reduces the size and component count of many circuits.ApplicationsµP Voltage MonitoringBattery-Backup SwitchingHigh/Low Temperature, Pressure, Voltage AlarmsLow-Battery DetectionOver/Undervoltage ProtectionPower Supply Fault MonitoringPower-Fail and Brownout Detection