The ICL761X–ICL764X family of monolithic CMOS op amps combine ultra-low input current with low-power operation over a wide supply voltage range. With pinselectable quiescent currents of 10µA, 100µA, or 1000µA per amplifier, these op amps will operate from ±1V to ±8V power supplies, or from single supplies from 2V to 16V. The CMOS outputs swing to within millivolts of the supply voltages.The ultra-low bias current of 1pA makes this family of op amps ideal for long time constant integrators, picoammeters, low droop rate sample/hold amplifiers and other applications where input bias and offset currents are critical. A low noise current of 0.01pA and an input impedance of 1012Ω ensure optimum performance with very high source impedances in such applications as pH meters and photodiode amplifiers.ApplicationsBattery-Powered InstrumentsHearing Aids and Microphone AmplifiersLong-Time Constant IntegratorsLow Droop Rate Sample/Hold AmplifiersLow-Frequency Active FiltersLow-Leakage AmplifiersPicoammeters

The ICL761X–ICL764X family of monolithic CMOS op amps combine ultra-low input current with low-power operation over a wide supply voltage range. With pinselectable quiescent currents of 10µA, 100µA, or 1000µA per amplifier, these op amps will operate from ±1V to ±8V power supplies, or from single supplies from 2V to 16V. The CMOS outputs swing to within millivolts of the supply voltages.The ultra-low bias current of 1pA makes this family of op amps ideal for long time constant integrators, picoammeters, low droop rate sample/hold amplifiers and other applications where input bias and offset currents are critical. A low noise current of 0.01pA and an input impedance of 1012Ω ensure optimum performance with very high source impedances in such applications as pH meters and photodiode amplifiers.ApplicationsBattery-Powered InstrumentsHearing Aids and Microphone AmplifiersLong-Time Constant IntegratorsLow Droop Rate Sample/Hold AmplifiersLow-Frequency Active FiltersLow-Leakage AmplifiersPicoammeters

The ICL761X–ICL764X family of monolithic CMOS op amps combine ultra-low input current with low-power operation over a wide supply voltage range. With pinselectable quiescent currents of 10µA, 100µA, or 1000µA per amplifier, these op amps will operate from ±1V to ±8V power supplies, or from single supplies from 2V to 16V. The CMOS outputs swing to within millivolts of the supply voltages.The ultra-low bias current of 1pA makes this family of op amps ideal for long time constant integrators, picoammeters, low droop rate sample/hold amplifiers and other applications where input bias and offset currents are critical. A low noise current of 0.01pA and an input impedance of 1012Ω ensure optimum performance with very high source impedances in such applications as pH meters and photodiode amplifiers.ApplicationsBattery-Powered InstrumentsHearing Aids and Microphone AmplifiersLong-Time Constant IntegratorsLow Droop Rate Sample/Hold AmplifiersLow-Frequency Active FiltersLow-Leakage AmplifiersPicoammeters

The ICL7665 warns microprocessors (µPs) of overvoltage and undervoltage conditions. It draws a typical operating current of only 3µA. The trip points and hysteresis of the two voltage detectors are individually programmed via external resistors to any voltage greater than 1.3V. The ICL7665 will operate from any supply voltage in the 1.6V to 16V range, while monitoring voltages from 1.3V to several hundred volts. The Maxim ICL7665A is an improved version with a 2%-accurate VSET1 threshold and guaranteed performance over temperature.The 3µA quiescent current of the ICL7665 makes it ideal for voltage monitoring in battery-powered systems. In both battery- and line-powered systems, the unique combination of a reference, two comparators, and hysteresis outputs reduces the size and component count of many circuits.ApplicationsµP Voltage MonitoringBattery-Backup SwitchingHigh/Low Temperature, Pressure, Voltage AlarmsLow-Battery DetectionOver/Undervoltage ProtectionPower Supply Fault MonitoringPower-Fail and Brownout Detection

The Maxim ICM7211 (LCD) and ICM7212 (LED) four digit, seven segment display drivers include input data latches, BCD to segment decoders, and all level translation and timing circuits needed to drive non-mulitplexed displays.Both the ICM7211 and ICM7212 are available in two data input configurations: a mulitplexed BCD interface version and a microprocessor interface version. The multiplexed BCD interface version has four BCD data inputs and four separate digit strobes. The microprocessor interface versions, designated by an 'M' suffix, have four chip selects or WRITE inputs.The ICM7211 and ICM7212 decode the BCD data via an onboard character font ROM. There are two different character fonts available, hexadecimal and Code B.ApplicationsDigital Panel DisplaysIntelligent InstrumentsMicroprocessor-to-Visual CommunicationRemote Display Units

The Maxim ICM7211 (LCD) and ICM7212 (LED) four digit, seven segment display drivers include input data latches, BCD to segment decoders, and all level translation and timing circuits needed to drive non-mulitplexed displays.Both the ICM7211 and ICM7212 are available in two data input configurations: a mulitplexed BCD interface version and a microprocessor interface version. The multiplexed BCD interface version has four BCD data inputs and four separate digit strobes. The microprocessor interface versions, designated by an 'M' suffix, have four chip selects or WRITE inputs.The ICM7211 and ICM7212 decode the BCD data via an onboard character font ROM. There are two different character fonts available, hexadecimal and Code B.ApplicationsDigital Panel DisplaysIntelligent InstrumentsMicroprocessor-to-Visual CommunicationRemote Display Units

LINEAR VOLT REG, ADJ, 0.04A, DIP-8; Fixed Output Voltage Nom.: -; Adjustable Output Voltage Min: 1.3V; Adjustable Output Voltage Max: 16V; Input Voltage Min: 2V; Input Voltage Max: 16V; Product Range: -; Output Current: 40mA; O

Position