BRADY MATERIAL DISPENSER 5 ROLL KIT / KIT

CABINET GANGING KIT

I3300 LEAN BWS SFID SUITE KIT / KIT

20 V, 500 mA, Low Noise, CMOS LDO Features: Input voltage range: 3.3 V to 20 V Maximum output current: 500 mA Low Noise: 15 μV rms for fixed output versions PSRR Performance of 60 dB at 10 kHz, VOUT = 3.3 V Reverse current protection Low dropout voltage: 350 mV at 500 mA Initial accuracy: ±0.8% Accuracy over line, load, and temperature −2% to +1%, TJ = −40°C to +125°C −1.25% to +1%, TJ = 0°C to +85°C Low quiescent current (VIN = 5 V), IGND = 900 μA with 500 mA load Low shutdown current: <40 μA at VIN = 12 V, stable with small 1 μF ceramic output capacitor 7 fixed output voltage options: 1.5 V, 1.8 V, 2.5 V, 3 V, 3.3 V, 5 V, and 9 V Adjustable output from 1.22 V to VIN − VDO Foldback current limit and thermal overload protection User programmable precision UVLO/enable Power-good indicator 8-lead LFCSP and 8-lead SOIC packages

5W AutoResonant Wireless Power Transmitter Features: Monolithic 5W Wireless Power Transmitter AutoResonant™ Switching Frequency Adjusts to Resonant Capacitance and Transmit Coil Inductance* Transmit Power Automatically Adjusts to Receiver Load* Input Voltage Range: 3V to 5.5V Integrated 100mΩ Full Bridge Switches Multiple Foreign Object Detection Methods Programmable Average Input Current Limit and Monitor NTC Input for System/Component Temperature Qualified Power Transfer Wide Operating Switching Frequency Range: 50kHz to 250kHz Thermally Enhanced 4mm × 5mm QFN 20-Lead Package

Multi-Sensor High Accuracy Digital Temperature Measurement System Features: Directly Digitize RTDs, Thermocouples, Thermistors, and Diodes Single 2.85V to 5.25V Supply Results Reported in °C or °F 20 Flexible Inputs Allow Interchanging Sensors Automatic Thermocouple Cold Junction Compensation Built-In Standard and User-Programmable Coefficients for Thermocouples, RTDs and Thermistors Configurable 2-, 3- or 4-Wire RTD Configurations Measures Negative Thermocouple Voltages Automatic Burn Out, Short-Circuit and Fault Detection Buffered Inputs Allow External Protection Simultaneous 50Hz/60Hz Rejection Includes 10ppm/°C (max) Reference (I-Grade)

High Voltage Buck-Boost Battery ChargeController with Maximum Power PointTracking (MPPT) and I2C Features: VIN Range: 6V to 80V VBAT Range: 1.3V to 80V Single Inductor Allows VIN Above, Below, or Equal to VBAT Automatic MPPT for Solar Powered Charging Automatic Temperature Compensation I2C Telemetry and Configuration Internal EEPROM for Configuration Storage Operation from Solar Panel or DC Supply Four Integrated Feedback Loops Synchronizable Fixed Frequency: 100kHz to 400kHz 64-Lead (7mm × 11mm × 0.75mm) QFN Package

18 GHz to 44 GHz, GaAs, pHEMT, MMIC, 1/2 W Power Amplifier Features: Output P1dB: 29 dBm PSAT: 29.5 dBm Gain: 23.5 dB Output IP3: 38 dBm Supply voltage: 5 V at 800 mA Integrated power detector 50 Ω matched input/output Die size: 2.750 mm × 1.805 mm × 0.102 mm

The ADF7030-1 is a fully integrated, radio transceiver achieving high performance at very low power. The ADF7030-1 is ideally suited for applications that require long range, network robustness, and long battery life. It is suitable for applications that operate in the ISM, SRD, and licensed frequency bands at 169.4 MHz to 169.6 MHz, 426 MHz to 470 MHz, and 863 MHz to 960 MHz. It provides extensive support for standards-based protocols like IEEE802.15.4g while also providing flexibility to support a wide range of proprietary protocols.The highly configurable low intermediate frequency (IF) receiver supports a large range of receiver channel bandwidths from 2.6 kHz to 406 kHz. This range of receiver channel bandwidths allows the ADF7030-1 to support ultranarrow-band, narrow-band, and wideband channel spacing.The ADF7030-1 features two independent PAs supporting output power ranges of −20 dBm to +13 dBm and −20 dBm to +17 dBm. The PAs support ultrafine adjustment of the power with a step resolution of 0.1 dB. The PA output power is exceptionally robust over temperature and voltage. The PAs have an automatic power ramp control to limit spectral splatter to meet regulatory standards.The ADF7030-1 features an on-chip ARM® Cortex®-M0 processor that performs radio control, radio calibration, and packet management. Cortex-M0 eases the processing burden of the host processor because the ADF7030-1 integrates the lower layers of a typical communication protocol stack. This internal processor also permits the download and execution of Analog Devices, Inc., provided firmware modules that can extend the functionality of the ADF7030-1.The ADF7030-1 has two packet modes: generic packet mode and IEEE802.15.4g mode. In generic packet mode, the packet format is highly flexible and fully programmable, thereby ensuring its compatibility with proprietary packet formats. In IEEE802.15.4g packet mode, the packet format conforms to the IEEE802.15.4g standard. FEC, as per the IEEE802.15.4g standard, is also supported.The ADF7030-1 operates with a power supply range of 2.2 V to 3.6 V and has very low power consumption in both Tx and Rx modes, enabling long lifetimes in battery-operated systems. An ultralow power deep sleep mode achieves a typical current of 10 nA with the configuration memory retained.A complete wireless solution can be built using a small number of external discrete components and a host processor (typically a microcontroller). The host processor can configure the ADF7030-1 using a simple command-based protocol over a standard 4-wire SPI interface. A single-byte command transitions the radio between states or performs a radio function.The ADF7030-1 is available in two package types: a 6 mm × 6 mm, 40-lead LFCSP and a 7 mm × 7 mm, 48-lead LQFP. Both package types use NiPdAu plating to mitigate against silver migration in high humidity applications. The ADF7030-1 operating temperature range is −40°C to +85°C.For Figure 13 to Figure 19, Figure 30, Figure 42, Figure 60, Figure 61, and Figure 75 in the Typical Performance Characteristics section, PA_COARSE is a programmable value that provides a coarse adjustment of the PA output power. This value can be programmed in the range of 1 to 6 for PA1, and from 1 to 10 for PA2. PA_FINE is a programmable value that provides a fine adjustment of the PA output power. This value can be programmed in the range of 3 to 127 for both PA1 and PA2. PA_MICRO is a programmable value that provides a microadjustment (typically <0.1 dB) of the PA output power. This value can be programmed in the range of 1 to 31 for both PA1 and PA2. PAOLDO_VOUT_CON is a programmable value that configures the internal LDO voltage that provides bias for the PA. For additional information on these bit settings, see the ADF7030-1 Software Reference Manual, which is the detailed programming guide for the device.Applications IEEE 802.15.4g (MR-FSK PHY)  Wireless M-Bus (EN 13757-4) Smart metering Security and building automation  Active tag asset tracking Industrial control Wireless sensor networks (WSNs)

EVALUATION KIT, LOGARITHMIC AMPLIFIER;