EVALUATION KIT, 800KHZ, 2.7V-5.5V, 10MA;

Multi-Sensor High Accuracy Digital Temperature Measurement System with EEPROM Features:Directly Digitizes 2-, 3-, or 4-Wire RTDs, Thermocouples, Thermistors, and DiodesOn-Chip EEPROM (LTC2986-1) Stores Channel Configuration Data and Custom CoefficientsSingle 2.85V to 5.25V Supply10 Flexible Inputs Allow Interchanging SensorsAutomatic Thermocouple Cold Junction CompensationBuilt-In Standard and User-Programmable Coefficients for Thermocouples, RTDs and ThermistorsMeasures Negative Thermocouple VoltagesAutomatic Burn Out, Short-Circuit and Fault DetectionBuffered Inputs Allow External ProtectionSimultaneous 50Hz/60Hz RejectionIncludes 15ppm/°C (Max) ReferenceIncludes Special Protection Modes

Up to 1GHz SHARC+ DSP with 640KB L1, 1024KB Shared L2 SRAM, 400-Ball CSP_BGA Features:SHARC+ Core infrastructure 800MHz (max) or 1GHz (max) Core clock frequency 640KB on-chip Level 1 (L1) SRAM memory (with parity) increases low latency performance 32-bit, 40-bit & 64-bit floating point support 32-bit fixed point Byte, short-word, word, long-word addressedMemory 1024KB on-chip Level 2 (L2) SRAM with ECC protection - eliminates need for external memory in many use cases One Level 3 (L3) interface optimized for low system power, providing 16-bit interface to DDR3 (supporting 1.35 V capable DDR3L devices) SDRAM devices16-bit DDR/DDR3L Memory Controller 1.35V support for DDR3LAdvanced Hardware Accelerators Enhanced FIR/IIR offload engines running at Core clock frequency for added processing power Security Crypto Engines with OTPPowerful DMA SystemInnovative Digital Audio Interface (DAI) includes: 8x Full SPORT interfaces w/TDM & I2S modes 2x S/PDIF Rx/Tx, 8 ASRC pairs 4x Precision Clock Generators 28 BuffersOther Peripheral Connectivity / Interfaces: 2x Quad SPI, 1x Octal SPI MLB 3-pin 6x I2C,3x UARTs 2x Link Ports 10x General Purpose Timer, 1x General Purpose Counter 2x Watchdog Timers 4-ch 12bit Housekeeping ADCs 40 GPIO pins, 28 DAI pins Thermal SensorPackage 17mm x 17mm (0.8mm pitch) 400-ball CSP_BGAAdditional Features Security and Protection Crypto hardware accelerators Fast secure boot with IP protection Enhanced FIR and IIR accelerators running up to 1 GHz AEC-Q100 qualified for automotive applications

High Performance, +3.3V Clock Generator, 25 - 2500 MHz Features: 3.3 V Only, Single Supply Rail Operation Output Frequency Range: 25 MHz - 2500 MHz Integer or Fractional-N mode Frequency Translation Configurable LVDS-compatible or LVPECL type Differential Outputs “Power Priority” and “Performance Priority” modes <97 fs RMS Jitter Generation (12 kHz-20 MHz, 2500MHz, Typ) -163 dBc/Hz Phase Noise Floor to Improve ADC/DAC SNR (maximum output swing levels) Adjustable PLL Loop BW via External Filter Output Disable/Mute Control Lock Detect Signal Exact Frequency Mode to achieve reference frequency tuning, and 0 Hz frequency error 40 Lead 6×6mm SMT Package: 36mm2

The HMC830LP6GE is a low noise, wideband, Fractional-N Phase-Locked-Loop (PLL) that features an integrated Voltage Controlled Oscillator (VCO) with a fundamental frequency of 1500 MHz - 3000 MHz, and an integrated VCO Output Divider (divide by 1/2/4/6.../60/62), that together allow the HMC830LP6GE to generate frequencies from 25 MHz to 3000 MHz. The integrated Phase Detector (PD) and delta-sigma modulator, capable of operating at up to 100 MHz, permit wider loop-bandwidths with excellent spectral performance.The HMC830LP6GE features industry leading phase noise and spurious performance, across all frequencies, that enable it to minimize blocker effects, and improve receiver sensitivity and transmitter spectral purity. Its superior performance makes it the ideal device for multi channel multi standard wide band transceivers. HMC830LP6GE can be used as an LO for RF mixers, a clock source for high-frequency data-converters, or a tunable reference source for ultra-low spurious applications.Additional features of the HMC830LP6GE include RF output power control from 0 to 9 dB (3 dB steps), output Mute function, and a delta-sigma modulator Exact Frequency Mode which enables users to generate output frequencies with 0 Hz frequency error.For theory of operation and register map refer to the 'PLLs with Integrated VCOs - RF VCOs Operating Guide' Operating Guide.Applications Cellular/4G Infrastructure Repeaters and Femtocells Communications Test Equipment CATV Equipment Phased Array Applications Very High Data Rate Radios Tunable Reference Source for Spurious- Free Performance

MAX2066 - Amplifier 50MHz ~ 1GHz Evaluation Board

SENSING ANALOG DEVELOPMENT KITS;

20 V, 500 mA, Low Noise, CMOS LDO Features: Input voltage range: 3.3 V to 20 V Maximum output current: 500 mA Low Noise: 15 μV rms for fixed output versions PSRR Performance of 60 dB at 10 kHz, VOUT = 3.3 V Reverse current protection Low dropout voltage: 350 mV at 500 mA Initial accuracy: ±0.8% Accuracy over line, load, and temperature −2% to +1%, TJ = −40°C to +125°C −1.25% to +1%, TJ = 0°C to +85°C Low quiescent current (VIN = 5 V), IGND = 900 μA with 500 mA load Low shutdown current: <40 μA at VIN = 12 V, stable with small 1 μF ceramic output capacitor 7 fixed output voltage options: 1.5 V, 1.8 V, 2.5 V, 3 V, 3.3 V, 5 V, and 9 V Adjustable output from 1.22 V to VIN − VDO Foldback current limit and thermal overload protection User programmable precision UVLO/enable Power-good indicator 8-lead LFCSP and 8-lead SOIC packages

Wireless Li-Ion Charger with 1.2V Step-Down DC/DC Converter Features: Wireless Li-Ion Battery Charger Plus High Efficiency Multi-Mode Charge Pump DC/DC Programmable Charge Current from 1mA to 50mA Via an External Resistor Wideband Rx Frequency: DC to >10MHz Integrated Rectifier with Overvoltage Limit Charge Voltage: 4.2V Low Battery Disconnect: 3.0V NTC Pin for Temperature Qualified Charging DC/DC Regulated Output: 1.2V DC/DC Output Current: Up to 60mA 50kHz/75kHz Switching, No Audible Noise Pushbutton and/or Digital on/off Control for DC/DC Thermally Enhanced 12-Lead 2mm 2mm LQFN Package

8-Channel PMBus Power System Manager Featuring Accurate Output Voltage Measurement Features: Sequence, Trim, Margin and Supervise Eight Power Supplies Manage Faults, Monitor Telemetry and Create Fault Logs PMBus™ Compliant Command Set Supported by LTpowerPlay® GUI Margin or Trim Supplies to Within 0.25% of Target Fast OV/UV Supervisors Per Channel Coordinate Sequencing and Fault Management Across Multiple LTC PSM Devices Automatic Fault Logging to Internal EEPROM Operate Autonomously without Additional Software Internal Temperature and Input Voltage Supervisors Accurate Monitoring of Eight Output Voltages, Input Voltage and Internal Die Temperature I2C/SMBus Serial Interface Can Be Powered from 3.3V, or 4.5V to 15V Programmable Watchdog Timer 100% Pin-Compatible Upgrade to the LTC2978/LTC2978A Available in 64-Pin 9mm × 9mm QFN PackageAEC-Q100 Qualified for Automotive Applications