EVAL KIT CURRENT-LIMITER; Silicon Manufacturer:Maxim Integrated Products; Silicon Core

The MAX1471 low-power, CMOS, superheterodyne, RF dual-channel receiver is designed to receive both amplitude-shift-keyed (ASK) and frequency-shift-keyed (FSK) data without reconfiguring the device or introducing any time delay normally associated with changing modulation schemes. The MAX1471 requires few external components to realize a complete wireless RF digital data receiver for the 300MHz to 450MHz ISM bands.The MAX1471 includes all the active components required in a superheterodyne receiver including: a low-noise amplifier (LNA), an image-reject (IR) mixer, a fully integrated phase-locked loop (PLL), local oscillator (LO), 10.7MHz IF limiting amplifier with received-signal-strength indicator (RSSI), low-noise FM demodulator, and a 3V voltage regulator. Differential peak-detecting data demodulators are included for both the FSK and ASK analog baseband data recovery. The MAX1471includes a discontinuous receive (DRX) mode for low-power operation, which is configured through a serial interface bus.The MAX1471 is available in a 32-pin thin QFN package and is specified over the automotive -40°C to +125°C temperature range.ApplicationsAutomotive Remote Keyless Entry (RKE)Garage Door OpenersHome AutomationLocal Telemetry SystemsMedical SystemsSecurity SystemsTire-Pressure Monitoring SystemsWireless KeysWireless Sensors

4-Port IEEE 802.3bt PoE PSE Controller Features: Four PSE Ports Two Power Channels per Port Low Power Path Dissipation per Channel 150mΩ Sense Resistance 30mΩ or Lower MOSFET RDS(ON) Chipset Provides Electrical Isolation Eliminates Optos and Isolated 3.3V Supply Very High Reliability Multipoint PD Detection Connection Check Distinguishes Single-Signature and Dual-Signature PDs Fully Compliant IEEE 802.3bt Type 3 and 4 PSE Compliant Support for Type 1, 2, 3, and 4 PDs Continuous, Dedicated Per-Port Power and Current Monitoring Per-Port Power Policing 1MHz I2C Compatible Serial Control Interface Pin or I2C Programmable PD Power Up to 71.3W Available in a 40-Lead 6mm × 6mm (LTC4292) and 24-Lead 4mm × 4mm (LTC4291-1) QFN Packages

Clock Generator with Fractional-N PLL & Integrated VCO SMT, 125 - 350 MHz Features: Frequency Range: 125 - 350 MHz 75 fs RMS Jitter Generation (Typical) Exceeds G.8251 & GR-253-CORE Jitter Specifications -165 dBc/Hz Phase Noise floor Maximum Phase Detector Rate 100 MHz Figure of Merit (FOM) -227 dBc/Hz 24-Bit Step Size, Resolution 3 Hz Typical Exact Frequency Mode Built-in Digital Self Test 40 Lead 6x6mm SMT Package: 36mm2

Multi-Sensor High Accuracy Digital Temperature Measurement System with EEPROM Features:Directly Digitizes 2-, 3-, or 4-Wire RTDs, Thermocouples, Thermistors, and DiodesOn-Chip EEPROM (LTC2986-1) Stores Channel Configuration Data and Custom CoefficientsSingle 2.85V to 5.25V Supply10 Flexible Inputs Allow Interchanging SensorsAutomatic Thermocouple Cold Junction CompensationBuilt-In Standard and User-Programmable Coefficients for Thermocouples, RTDs and ThermistorsMeasures Negative Thermocouple VoltagesAutomatic Burn Out, Short-Circuit and Fault DetectionBuffered Inputs Allow External ProtectionSimultaneous 50Hz/60Hz RejectionIncludes 15ppm/°C (Max) ReferenceIncludes Special Protection Modes

EVALUATION KIT, 16-BIT D/A CONVERTER;

EVALUATION KIT, 330KHZ, 36V, 2A;

EVAL KIT, 12BIT, A/D CONVERTER;

EVAL KIT, 16BIT, A/D CONVERTER;

ENCODER KIT, STEPPER & PMSM/BLDC MOTOR; Accessory Type:Encoder Kit; For Use With:Stepper Motors and 3-Phase PMSM/BLDC Motors; Product Range:-; SVHC:No SVHC (27-Jun-2018) RoHS Compliant: Yes