Interface Development Tools PS09-EVA-KIT

100MHz to 70GHz Linear-in-dB RMS Power Detector with 35dB Dynamic Range Features: Ultra Wide Matched Input Frequency Range: 100MHz to 70GHz 35dB Linear Dynamic Range (< ±1dB Error) 28.5mV/dB Logarithmic Slope ±2dB Flat Response from 100MHz to 60GHz Accurate RMS Power Measurement of High Crest Factors (Up to 12dB) Modulated Waveforms Low Power Shutdown Mode Low Supply Current: 33mA at 3.3V (Typical) Small 2mm × 2mm Plastic DFN8 Package I-Grade: −40°C to 105°C Rated H-Grade: −40°C to 125°C Rated with Guaranteed Log-Slope and Log-Intercept ESD Rating: 2500V HBM, 1500V CDM

GaAs, pHEMT, MMIC,1/2 W, 20 GHz to 44 GHz, Power Amplifier Features: Output P1dB: 28 dBm (typical at 34 GHz to 44 GHz) PSAT: 30 dBm (typical at 20 GHz to 34 GHz) Gain: 15 dB (typical at 34 GHz to 44 GHz) IP3: 40 dBm (typical) Supply voltage: 5 V at 600 mA Die size: 2.75 mm × 1.805 mm × 0.1 mm

18 GHz to 44 GHz, GaAs, pHEMT, 32 dBm (>1 W), MMIC Power Amplifier Features:ADPA7005AEHZ Output P1dB: up to 31 dBm typical PSAT: up to 32 dBm typical Gain: up to 15.5 dB typical Output IP3: up to 42.5 dBm typical Supply voltage: 5 V at 1400 mA 50 matched input/output 18-terminal, 7 mm × 7 mm LCC_HS package Integrated power detectorADPA7005CHIP Output P1dB: 31 dBm typical at 20 GHz to 34 GHz PSAT: 32 dBm typical at 20 GHz to 34 GHz Gain: 17 dB typical at 20 GHz to 34 GHz Output IP3: 41 dBm typical at 20 GHz to 34 GHz Supply voltage: 5 V at 1200 mA maximum 50 Ω matched input/output Die size: 3.75 mm × 3.47 mm × 0.1 mm

Quectel Wireless Solutions

The MAX2066 high-linearity digital variable-gain amplifier (VGA) is a monolithic SiGe BiCMOS attenuator and amplifier designed to interface with 50Ω systems operating in the 50MHz to 1000MHz frequency range (See the Typical Application Circuit in the full data sheet). The digital attenuator is controlled as a slave peripheral using either the SPI™-compatible interface or a parallel bus with 31dB total adjustment range in 1dB steps. An added feature allows 'rapid-fire' gain selection between each of four steps, preprogrammed by the user through the SPI-compatible interface. The 2-pin control allows the user to quickly access any one of four customized attenuation states without reprogramming the SPI bus.Because each stage has its own RF input and RF output, this component can be configured to either optimize NF (amplifier configured first), or OIP3 (amplifier last). The device's performance features include 22dB amplifier gain (amplifier only), 5.2dB NF at maximum gain (includes attenuator insertion loss), and a high OIP3 level of +42.4dBm. Each of these features makes the MAX2066 an ideal VGA for numerous receiver and transmitter applications.In addition, the MAX2066 operates from a single +5V supply with full performance, or a single +3.3V supply with slightly reduced performance, and has an adjustable bias to trade current consumption for linearity performance. This device is available in a compact 40-pin thin QFN package (6mm x 6mm) with an exposed pad. Electrical performance is guaranteed over the extended temperature range (TC = -40°C to +85°C).ApplicationsCable Modem Termination Systems (CMTS)Cellular Band WCDMA and cdma2000® Base StationsFixed Broadband Wireless AccessGSM 850/GSM 900 EDGE Base StationsIF and RF Gain StagesMilitary SystemsRFID Handheld and Portal ReadersVideo-on-Demand (VOD) and DOCSIS®-Compliant EDGE QAM ModulationWiMAX and LTE Base Stations and Customer Premise EquipmentWireless Local Loop

The MAX19790 is a dual, general-purpose analog voltage variable attenuator (VVA) designed to interface with 50Ω systems operating in the 250MHz to 4000MHz frequency range. Each attenuator includes a control circuit that provides 22dB of attenuation range with a linear control slope of 10dB/V.Both attenuators share a common analog control and can be cascaded together to yield 44dB of total dynamic range, with a combined linear control slope of 20dB/V.The IC is a monolithic device designed on one of Maxim's proprietary SiGe BiCMOS processes. The device operates from a single +5.0V supply and is available in a compact, 36-pin thin QFN package (6mm x 6mm x 0.8mm) with an exposed pad. Electrical performance is guaranteed over the extended -40°C to +85°C temperature range.ApplicationsAutomatic Level Control (ALC)Broadband System Applications, Including Wireless Infrastructure Digital and Spread-Spectrum Communication SystemsGeneral Test EquipmentLineup Gain TrimMicrowave Terrestrial LinksReceiver Gain ControlTemperature Compensation CircuitsTransmitter Gain ControlVSAT/Satellite ModemsWCDMA/LTE, TD-SCDMA/TD-LTE, WiMAX®, cdma2000®, GSM/EDGE and MMDS Base Stations

The MAX2674/MAX2676 are ultra-small, high-IP3, low-noise amplifiers (LNAs) designed for GPS L1, Galileo, and GLONASS applications. Designed in Maxim's advanced SiGe process, the devices are also equipped with an autosensing feature for applications that enable the use of external antennas. These high-performance LNAs provide high gain and an ultra-low noise figure while optimizing the input-referred 2dB compression point and 3rd-order intercept point.The ultra-small size is ideal for front-end modules and receiver applications in cellular phones, smartphones, PDAs, PNDs, or other custom GNSS applications. The MAX2674/MAX2676 operate from a 1.6V to 3.6V single supply. The MAX2674 is optimized for high gain, while the MAX2676 is optimized for high linearity. A shutdown feature is present in both devices reducing the supply current to less than 10µA. The antenna port automatically senses when an external antenna is connected, eliminating the need for additional control circuitry while also providing improved short-circuit protection. The MAX2674/MAX2676 are available in an ultra-small, RoHS-compliant 0.86mm x 1.26mm x 0.64mm wafer-level package (WLP).ApplicationsCellular and SmartphonesFront-End SAW ModulesPersonal Navigation Devices (PNDs)Receiver ModulesRecreational, Marine NavigationTelematics (Asset Tracking and Management)

The MAX2674/MAX2676 are ultra-small, high-IP3, low-noise amplifiers (LNAs) designed for GPS L1, Galileo, and GLONASS applications. Designed in Maxim's advanced SiGe process, the devices are also equipped with an autosensing feature for applications that enable the use of external antennas. These high-performance LNAs provide high gain and an ultra-low noise figure while optimizing the input-referred 2dB compression point and 3rd-order intercept point.The ultra-small size is ideal for front-end modules and receiver applications in cellular phones, smartphones, PDAs, PNDs, or other custom GNSS applications. The MAX2674/MAX2676 operate from a 1.6V to 3.6V single supply. The MAX2674 is optimized for high gain, while the MAX2676 is optimized for high linearity. A shutdown feature is present in both devices reducing the supply current to less than 10µA. The antenna port automatically senses when an external antenna is connected, eliminating the need for additional control circuitry while also providing improved short-circuit protection. The MAX2674/MAX2676 are available in an ultra-small, RoHS-compliant 0.86mm x 1.26mm x 0.64mm wafer-level package (WLP).ApplicationsCellular and SmartphonesFront-End SAW ModulesPersonal Navigation Devices (PNDs)Receiver ModulesRecreational, Marine NavigationTelematics (Asset Tracking and Management)

The MAX5387 dual, 256-tap, volatile, low-voltage linear taper digital potentiometer offers three end-to-end resistance values of 10kΩ, 50kΩ, and 100kΩ. Operating from a single +2.6V to +5.5V power supply, the device provides a low 35ppm/°C end-to-end temperature coefficient. The device features an I2C interface.The small package size, low supply operating voltage, low supply current, and automotive temperature range of the MAX5387 make the device uniquely suitable for the portable consumer market and battery-backup industrial applications.The MAX5387 is specified over the automotive -40°C to +125°C temperature range and is available in a 14-pin TSSOP package.ApplicationsAdjustable Voltage References/Linear RegulatorsLow-Voltage Battery ApplicationsMechanical Potentiometer ReplacementOffset and Gain ControlPortable Electronics