WLAN COMM MODULE, 160MHZ;

Quectel Wireless Solutions

Educational Robotic Kits TDK RoboKit1 Full PKG

GaAs, pHEMT, MMIC,1/2 W, 20 GHz to 44 GHz, Power Amplifier Features: Output P1dB: 28 dBm (typical at 34 GHz to 44 GHz) PSAT: 30 dBm (typical at 20 GHz to 34 GHz) Gain: 15 dB (typical at 34 GHz to 44 GHz) IP3: 40 dBm (typical) Supply voltage: 5 V at 600 mA Die size: 2.75 mm × 1.805 mm × 0.1 mm

18 GHz to 44 GHz, GaAs, pHEMT, 32 dBm (>1 W), MMIC Power Amplifier Features:ADPA7005AEHZ Output P1dB: up to 31 dBm typical PSAT: up to 32 dBm typical Gain: up to 15.5 dB typical Output IP3: up to 42.5 dBm typical Supply voltage: 5 V at 1400 mA 50 matched input/output 18-terminal, 7 mm × 7 mm LCC_HS package Integrated power detectorADPA7005CHIP Output P1dB: 31 dBm typical at 20 GHz to 34 GHz PSAT: 32 dBm typical at 20 GHz to 34 GHz Gain: 17 dB typical at 20 GHz to 34 GHz Output IP3: 41 dBm typical at 20 GHz to 34 GHz Supply voltage: 5 V at 1200 mA maximum 50 Ω matched input/output Die size: 3.75 mm × 3.47 mm × 0.1 mm

100MHz to 70GHz Linear-in-dB RMS Power Detector with 35dB Dynamic Range Features: Ultra Wide Matched Input Frequency Range: 100MHz to 70GHz 35dB Linear Dynamic Range (< ±1dB Error) 28.5mV/dB Logarithmic Slope ±2dB Flat Response from 100MHz to 60GHz Accurate RMS Power Measurement of High Crest Factors (Up to 12dB) Modulated Waveforms Low Power Shutdown Mode Low Supply Current: 33mA at 3.3V (Typical) Small 2mm × 2mm Plastic DFN8 Package I-Grade: −40°C to 105°C Rated H-Grade: −40°C to 125°C Rated with Guaranteed Log-Slope and Log-Intercept ESD Rating: 2500V HBM, 1500V CDM

The MAX148/MAX149 10-bit data-acquisition systems combine an 8-channel multiplexer, high-bandwidthtrack/hold, and serial interface with high conversion speed and low power consumption. They operate from a single +2.7V to +5.25V supply, and sample to 133ksps. Both devices’ analog inputs are software configurable for unipolar/bipolar and single-ended/differential operation.The 4-wire serial interface connects directly to SPI/QSPI™ and MICROWIRE™ devices without external logic. A serial-strobe output allows direct connection to TMS320-family digital signal processors. The MAX148/MAX149 use either the internal clock or an external serial-interface clock to perform successive-approximation analog-to-digital conversions.The MAX149 has an internal 2.5V reference, while the MAX148 requires an external reference. Both parts have a reference-buffer amplifier with a ±1.5% voltage-adjustment range.These devices provide a hard-wired active-low SHDN pin and a software-selectable power-down, and can be programmed to automatically shut down at the end of a conversion. Accessing the serial interface automatically powers up the MAX148/MAX149, and the quick turn-on time allows them to be shut down between all conversions. This technique can cut supply current to under 60µA at reduced sampling rates.The MAX148/MAX149 are available in 20-pin PDIP and 20-pin SSOP packages.For 4-channel versions of these devices, see the MAX1248/MAX1249 data sheet.ApplicationsBattery-Powered InstrumentsData AcquisitionMedical InstrumentsPen DigitizersPortable Data LoggingProcess Control

The MAX14842 translates digital signals between two domains that have different ground references of up to 72V. The device features six communication channels, two bidirectional and four unidirectional. Two of the four unidirectional channels go in each direction. The device is powered by two supply voltages that independently define the logic levels of each ground domain.The MAX14842 supports guaranteed data rates up to 30Mbps on the four unidirectional channels and up to 2Mbps on the two bidirectional channels. The bidirectional channels have open-drain outputs, making them suitable for I²C signals. I²C clock stretching and hot swapping is supported on the bidirectional channels.Undervoltage lockout ensures that the output pins have a defined behavior during power-up, power-down, and during supply transients. For proper operation, ensure that 0V ≤ (VGNDB - VGNDA) ≤ 72V. Note that GNDB must be greater than or equal to GNDA.The MAX14842 is available in a 16-pin TQFN package and is specified over the -40°C to +125°C automotive temperature range.ApplicationsBattery ManagementI2C, SMBus™, SPI™, and MICROWIRE™ SignalsMedical SystemsPower-Over-EthernetTelecommunication Systems

The MAX14986 dual-channel redriver is designed to redrive one full lane of SAS or SATA signals up to 6.0GT/s (gigatransfers per second) and operates from a single +3.3V supply.The MAX14986 features independent input equalization and output preemphasis. It enhances signal integrity at the receiver by equalizing the signal at the input and establishing preemphasis at the output of the device. SAS and SATA OOB (out-of-band) signaling is supported using high-speed amplitude detection on the inputs and squelch on the corresponding outputs. Inputs and outputs are all internally 50Ω terminated and must be AC-coupled to the SAS/SATA controller IC and SAS/SATA device.The MAX14986 is available in a small 28-pin, 3.5mm x 5.5mm TQFN package with flow-through traces for ease of layout. This device is specified over the -40°C to +85°C extended operating temperature range.ApplicationsCarrier BoardsComputer on ModulesIndustrial/Embedded PCsMedical EquipmentRack Server Industrial PCsTest Equipment

The MAX16126/MAX16127 load-dump/reverse-voltage protection circuits protect power supplies from damaging input voltage conditions, including overvoltage, reverse-voltage, and high-voltage transient pulses. Using a built-in charge pump, the devices control two external back-to-back n-channel MOSFETs that turn off and isolate downstream power supplies during damaging input conditions, such as an automotive load-dump pulse or a reverse-battery condition. Operation is guaranteed down to 3V to ensure proper operation during automotive cold-crank conditions. These devices feature a flag output (active-low FLAG) that asserts during fault conditions.For reverse-voltage protection, external back-to-back MOSFETs outperform the traditional reverse-battery diode, minimizing the voltage drop and power dissipation during normal operation.The MAX16126/MAX16127 use external resistors to adjust the overvoltage and undervoltage comparator thresholds for maximum flexibility.The MAX16127 provides limiter-mode fault management for overvoltage and thermal shutdown conditions; whereas the MAX16126 provides switch-mode fault management for overvoltage and thermal shutdown conditions. In the limiter mode, the output voltage is limited and active-low FLAG is asserted low during a fault. In the switch mode, the external MOSFETs are switched off and active-low FLAG is asserted low after a fault. The switch mode is available in four options: latch mode, 1 autoretry mode, 3 autoretry mode, and always autoretry mode.The MAX16126/MAX16127 are available in 12-pin TQFN packages. These devices operate over the automotive temperature range (-40°C to +125°C).ApplicationsAutomotiveAvionicsIndustrialTelecom/Server/Networking