The AD8225 is an instrumentation amplifier with fixed gain of 5 that sets new standards of performance.The superior CMRR of the AD8225 enables rejection of high frequency common mode voltage (80 dB Min @10 kHz).As a result,higher ambient levels of noise from utility lines,industrial equipment and other radiating sources,are rejected. Extended CMV range enables the AD8225 to extract low-level differential signals in the presence of high common-mode dc voltage levels even at low supply voltages.

The AD8304 is a monolithic logarithmic detector optimized for the measurement of low frequency signal power in fiber optic systems. It uses an advanced translinear technique to provide an exceptionally large dynamic range in a versatile and easily used form. Its wide measurement range and accuracy are achieved using proprietary design techniques and precise laser trimming. In most applications only a single positive supply, VP, of 5 V will be required, but 3.0 V to 5.5 V can be used, and certain applications benefit from the added use of a negative supply, VN. When using low supply voltages, the log slope is readily altered to fit the available span. The low quiescent current and chip disable features facilitate use in battery-operated applications.The AD8304 is available in a 14-lead TSSOP package and specified for operation from -40?C to +85?C.

The AD8306 is a complete IF limiting amplifier, providing bothan accurate logarithmic (decibel) measure of the input signal(the RSSI function) over a dynamic range of 100 dB, and aprogrammable limiter output, useful from 5 MHz to 400 MHz.An evaluation board is available for this product and may be ordered using the following product number: AD8306-EVAL. Schematic and layout for this evaluation board is contained in the product datasheet.

The AD8312 is a complete, low cost subsystem for the measurement of RF signals in the frequency range of 50 MHz to 3.5 GHz. It has a typical dynamic range of 45 dB and is intended for use in a wide variety of cellular handsets and other wireless devices. It provides a wider dynamic range and better accuracy than possible using discrete diode detectors. In particular, its temperature stability is excellent over the full operating range of ?40?C to +85?C.Its high sensitivity allows measurement at low power levels, thus reducing the amount of power that needs to be coupled to the detector. It is essentially a voltage-responding device, with a typical signal range of 1.25 mV to 224 mV rms or ?45 dBm to 0 dBm, referencing 50 ?.For convenience, the signal is internally ac-coupled, using a 5 pF capacitor to a load of 3 k? in shunt with 1.3 pF. This high-pass coupling, with a corner at approximately 16 MHz, determines the lowest operating frequency. Therefore, the source may be dc grounded.The AD8312 output, VOUT, increases from close to ground to about 1.2 V because the input signal level increases from 1.25 mV to 224 mV. A capacitor may be connected between the VOUT and CFLT pins when it is desirable to increase the time interval over which averaging of the input waveform occurs.The AD8312 is available in a 6-ball, 1.0 mm ? 1.5 mm, wafer-level chip scale package and consumes 4.2 mA from a 2.7 V to 5.5 V supply.Applications Cellular handsets (GSM, CDMA, WCDMA) RSSI and TSSI for wireless terminal devices Transmitter power measurement

The AD8337 is a low noise, single-ended, linear-in-dB, general-purpose variable gain amplifier (VGA) usable at frequencies from dc to 100 MHz; the ?3 dB bandwidth is 280 MHz. Excellent bandwidth uniformity across the entire gain range and low output-referred noise makes the AD8337 ideal for gain trim applications and for driving high speed analog-to-digital converters (ADCs).Excellent dc characteristics combined with high speed make the AD8337 particularly suited for industrial ultrasound, PET scanners, and video applications. Dual-supply operation enables gain control of negative-going pulses such as generated by photodiodes or photomultiplier tubes.The AD8337 uses the popular and versatile X-AMP? architecture, exclusively from Analog Devices, Inc., with a gain range of 24 dB. The gain control interface provides precise linear-in-dB scaling of 19.7 dB/V, referenced to VCOM.The AD8337 includes an uncommitted operational current-feedback preamplifier (PrA) that operates in inverting or noninverting configurations. Using external resistors, the device can be configured for gains of 6 dB or greater. The AD8337 is characterized by a noninverting PrA gain of 2? using two external 100 ? resistors. The attenuator has a range of 24 dB, and the output amplifier has a fixed gain of 8? (18.06 dB). The lowest nominal gain range is 0 dB to 24 dB and can be shifted up or down by adjusting the preamp gain. Multiple AD8337s can be connected in series for larger gain ranges, and for interstage filtering to suppress noise and distortion, and for nulling offset voltages.The operating temperature range is ?40?C to +85?C, and it is available in an 8-lead, 3 mm ? 3 mm LFCSP.Applications Gain trim PET scanners High performance AGC systems I/Q signal processing Video Industrial and medical ultrasound Radar receivers

The AD8338 is a variable gain amplifier (VGA) for applicationsthat require a fully differential signal path, low power, low noise,and a well-defined gain over frequency. Although the inputs aredifferential, the device can also be driven with a single-endedsource if required.The basic gain function is linear-in-dB and is controlled by thevoltage applied to Pin GAIN. The nominal gain range spansfrom 0 dB to 80 dB for control voltages between 0.1 V to 1.1 Vwith a slope of 12.5 mV/dB. The nominal gain range can beshifted up or down via direct access to Pin INPD and Pin INMD,the current inputs of the VGA. For example, driving the INPDand INMD pins with 50 ? resistors shifts the gain range up by20 dB, that is, 20 dB to 100 dB, and lowers the input referrednoise of the device to 1.5 nV/?Hz. Additionally, the gain slopecan be inverted via logic Pin MODE.The AD8338 includes additional circuit blocks to enable inputoffset correction and automatic gain control (AGC). DC offsetvoltages are removed by the offset correction circuit, whichbehaves like a high-pass filter whose corner is set with an externalcapacitor. The AGC function varies the gain of the AD8338 tomaintain a constant rms output voltage. An externally appliedvoltage to Pin VAGC with respect to the voltage at Pin VREFsets the output rms amplitude. A capacitor from Pin DETO toground sets the response time of the AGC circuit.The AD8338 offers additional versatility by providing access tothe internal summing nodes of the VGA core and the outputamplifiers. With the addition of a few external passive components,users can customize the gain, bandwidth, input impedance, andnoise profile of the device to fit their application.The AD8338 uses a single-supply voltage of 3.0 V to 5.0 V andis very power efficient, consuming as little as 3 mA quiescentcurrent at mid gain. The AD8338 is available in a 3 mm ? 3 mm,RoHS-compliant, 16-lead LFCSP and is specified over theindustrial temperature range of ?40?C to +85?C.APPLICATIONS Front end for inductive telemetry systems Ultrasonic signal receivers Signal compression for driving an ADC AGC amplifiers

DC1699A-A: Demo Board for the LT6108 High Side Current Sense Amplifier with Reference and Comparator.

The ADA4530-1 is a femtoampere (10?15 A) level input bias current operational amplifier suitable for use as an electrometer that also includes an integrated guard buffer. It has an operating voltage range of 4.5 V to 16 V, enabling it to operate in conventional 5 V and 10 V single supply systems as well as ?2.5 V and ?5 V dual supply systems.It provides ultralow input bias currents that are production tested at 25?C and at 125?C to ensure the device meets its performance goals in user systems. The integrated guard buffer isolates the input pins from leakage in the printed circuit board (PCB), minimizes board component count, and enables easy system design. The ADA4530-1 is available in an industry-standard surface-mount 8-lead SOIC package with a unique pinout optimized to prevent signals from coupling between the sensitive input pins, the power supplies, and the output pin while enabling easy routing of the guard ring traces.The ADA4530-1 also offers low offset voltage, low offset drift, and low voltage and current noise needed for the types of applications that require such low leakages.To maximize the dynamic range of the system, the ADA4530-1 has a rail-to-rail output stage that can typically drive to within 30 mV of the supply rails under a 10 k? load.The ADA4530-1 operates over the ?40?C to +125?C industrial temperature range and is available in an 8-lead SOIC package.Applications Laboratory and analytical instrumentation: spectrophotometers, chromatographs, mass spectrometers, and potentiostatic and amperostatic coulometry Instrumentation: picoammeters and coulombmeters Transimpedance amplifier (TIA) for photodiodes, ion chambers, and working electrode measurements High impedance buffering for chemical sensors and capacitive sensors

The ADA4851-1 (single), ADA4851-2 (dual), and ADA4851-4 (quad) are low cost, high speed, voltage feedback rail-to-rail output op amps. Despite their low price, these parts provide excellent overall performance and versatility. The 130 MHz, ?3 dB bandwidth and high slew rate make these amplifiers well suited for many general-purpose, high speed applications.The ADA4851 family is designed to operate at supply voltages as low as +3 V and up to ?5 V. These parts provide true single-supply capability, allowing input signals to extend 200 mV below the negative rail and to within 2.2 V of the positive rail. On the output, the amplifiers can swing within 60 mV of either supply rail.With their combination of low price, excellent differential gain (0.08%), differential phase (0.09?), and 0.1 dB flatness out to 11 MHz, these amplifiers are ideal for consumer video applications.The ADA4851 family is designed to work over the extended temperature range (?40?C to +125?C). The ADA4851-4W and ADA4851-2W are automotive grade versions, qualified for ?40?C to +125?C operation per AEC-Q100. See the Automotive Products section for more details.Applications Automotive infotainment systems Automotive driver assistance systems Consumer video Professional video Video switchers Active filters Clock buffers

The ADA4858-3 (triple) is a single-supply, high speed current feedback amplifier with an integrated charge pump that eliminates the need for negative supplies to output negative voltages or output a 0 V level for video applications. The 600 MHz, ?3 dB bandwidth and 600 V/?s slew rate make this amplifier well suited for many high speed applications. In addition, its 0.1 dB flatness out to 85 MHz at G = 2, along with its differential gain and phase errors of 0.01% and 0.02? into a 150 ? load, make it well suited for professional and consumer video applications.This triple operational amplifier is designed to operate on supply voltages of 3.3 V to 5 V, using only 42 mA of total quiescent current, including the charge pump. To further reduce the power consumption, it is equipped with a power-down feature that lowers the total supply current to as low as 2.5 mA when the amplifier is not being used. Even in power-down mode, the charge pump can be used to power external components. The maximum output current for external use is 50 mA at ?3 V. The amplifier also has a wide input common-mode voltage range that extends from 1.8 V below ground to 1.2 V below the positive rail at a 5 V supply.The ADA4858-3 is available in a 16-lead LFCSP, and it is designed to work over the extended industrial temperature range of ?40?C to +105?C.ApplicationsProfessional videoConsumer videoImagingActive filtersData Sheet, Rev. A, 05/09