Clock Buffer 1:2 Fanout 26GHz

The ADCLK944 is an ultrafast clock fanout buffer fabricated on the Analog Devices, Inc., proprietary XFCB3 silicon germanium (SiGe) bipolar process. This device is designed for high speed applications requiring low jitter.The device has a differential input equipped with center-tapped, differential, 100 Ω on-chip termination resistors. The input can accept dc-coupled LVPECL, CML, 3.3 V CMOS (single-ended), and ac-coupled 1.8 V CMOS, LVDS, and LVPECL inputs. A VREF pin is available for biasing ac-coupled inputs.The ADCLK944 features four full-swing emitter-coupled logic (ECL) output drivers. For LVPECL (positive ECL) operation, bias VCC to the positive supply and VEE to ground. For ECL operation, bias VCC to ground and VEE to the negative supply.The ECL output stages are designed to directly drive 800 mV each side into 50 Ω terminated to VCC − 2 V for a total differential output swing of 1.6 V.The ADCLK944 is available in a 16-lead LFCSP and is specified for operation over the standard industrial temperature range of −40°C to +85°C. APPLICATIONS Low jitter clock distribution Clock and data signal restoration Level translation Wireless communications Wired communications Medical and industrial imaging ATE and high performance instrumentation

The AD9522-31 provides a multioutput clock distribution function with subpicosecond jitter performance, along with an on-chip PLL and VCO. The on-chip VCO tunes from 1.72 GHz to 2.25 GHz. An external 3.3 V/5 V VCO/VCXO of up to 2.4 GHz can also be used. The AD9522 serial interface supports both SPI and I2C® ports. An in-package EEPROM can be programmed through the serial interface and store user-defined register settings for power-up and chip reset.The AD9522 features 12 LVDS outputs in four groups. Any of the 800 MHz LVDS outputs can be reconfigured as two 250 MHz CMOS outputs.Each group of outputs has a divider that allows both the divide ratio (from 1 to 32) and the phase (coarse delay) to be set. The AD9522 is available in a 64-lead LFCSP and can be operated from a single 3.3 V supply. The external VCO can have an operating voltage up to 5.5 V. The AD9522 is specified for operation over the standard industrialrange of −40°C to +85°C.The AD9520-3 is an equivalent part to the AD9522-3 featuringLVPECL / CMOS drivers instead of LVDS / CMOS drivers.1The AD9522 is used throughout this data sheet to refer to all the members of the AD9522 family. However, when AD9522-3 is used, it is referring to that specificmember of the AD9522 family.ApplicationsLow jitter, low phase noise clock distributionClock generation and translation for SONET, 10Ge, 10G FC, and other 10 Gbps protocolsForward error correction (G.710)Clocking high speed ADCs, DACs, DDSs, DDCs, DUCs, MxFEsHigh performance wireless transceiversATE and high performance instrumentationBroadband infrastructuresData Sheet, Rev. 0, 10/08

Real Time Clock

DELAY LINE;

Broadband Analog Time Delay SMT, DC - 24 GHz Features: Very Wide Bandwidth: DC - 24 GHz Continuous Adjustable Delay Range: 70 ps Single-Ended or Differential Operation Adjustable Differential Output Voltage Swing: 170 - 760 mVp-p @ 24 GHz Delay Control Modulation Bandwidth: 10 MHz Single Supply: +3.3V  24 Lead 4x4mm SMT Package: 16mm²

Microwave Wideband Synthesizer with Integrated VCO Features: RF output frequency range: 62.5 MHz to 32,000 MHz Fractional-N synthesizer and Integer N synthesizer High resolution 39-bit fractional modulus Typical spurious PFD: −90 dBc Integrated rms jitter: 38 fs (1 kHz to 100 MHz) Normalized phase noise floor: −234 dBc/Hz PFD operation to 250 MHz Reference frequency operation to 600 MHz Programmable divide by 1, 2, 4, 8, 16, 32, or 64 output 62.5 MHz to 8,000 MHz output at RF8x and RFAUX8x 8,000 MHz to 16,000 MHz output at RF16x 16,000 MHz to 32,000 MHz output at RF32x Lock time approximately 3 ms with automatic calibration Lock time <30 μs with autocalibration bypassed Analog and digital power supplies: 3.3 V VCO power supply: 3.3 V and 5 V RF output mute function 7mm × 7mm, 48-terminal LGA package

Ultralow Noise 0.35GHz to 6GHz Fractional-N Synthesizer Features:Low Noise Fractional-N PLLNo ΔΣ Modulator Spurs18-Bit Fractional Denominator350MHz to 6GHz VCO Input Range–226dBc/Hz Normalized In-Band Phase Noise Floor–274dBc/Hz Normalized In-Band 1/f Noise–157dBc/Hz Wideband Output Phase Noise FloorExcellent Integer Boundary Spurious PerformanceOutput Divider (1 to 6, 50% Duty Cycle)Output Buffer MutingCharge Pump Supply from 3.15V to 5.25VCharge Pump Current from 1mA to 11.2mAReference Input Frequency Up to 425MHzFast Frequency Switching

Ultralow Noise 0.37GHz to 6.39GHz Fractional-N Synthesizer with Integrated VCO Features:Low Noise Fractional-N PLL with Integrated VCONo Δ-Σ Modulator Spurs18-Bit Fractional Denominator–226 dBc/Hz Normalized In-Band Phase Noise Floor–274 dBc/Hz Normalized In-Band 1/f Noise–157 dBc/Hz Wideband Output Phase Noise FloorExcellent Integer Boundary Spurious PerformanceOutput Divider (1 to 6, 50% Duty Cycle)Output Buffer MutingReference Input Frequency Up to 425MHzFast Frequency SwitchingFracNWizard™ Software Design Tool Support

CLOCK & TIMING ANALOG DEV KITS;