3-V, RS-232 Serial Port Driver-Receiver Features: Green Idle power-saving mode Single 2.7 V to 3.6 V power supply Operates with 3 V logic 0.1 µF to 1 µF charge pump capacitors Low EMI Low power shutdown: 20 nA Full RS-232 compliance 460 kb/s data rate One receiver active in shutdown (ADM3307E/ADM3311E/ADM3312E/ADM3315E) Two receivers active in shutdown (ADM3310E) ESD >15 kV IEC 1000-4-2 on RS-232 I/Os ESD >15 kV IEC 1000-4-2 on CMOS and RS-232 I/Os (ADM3307E) Qualified for automotive applications

5.7 kV RMS/1.5 kV RMS, Quad-Channel LVDS 2.5 Gigabit Isolator (0 Reverse Channels) Features: 5.7 kV rms and 1.5 kV rms LVDS isolators Complies with TIA/EIA-644-A LVDS signal levels Quad-channel configuration Any data rate up to 2.5 Gbps switching with low jitter 10 Gbps total bandwidth across four channels 2.15 ns typical propagation delay Typical jitter: 0.82 ps rms random, 40 ps total peak Lower power 1.8 V supplies ±8 kV IEC 61000-4-2 ESD protection across isolation barrier High common-mode transient immunity: 100 kV/μs typical Safety and regulatory approvals (28-lead SOIC_W_FP package) UL (pending): 5700 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) VDE certificate of conformity (pending) DIN V VDE V 0884-11 (VDE V 0884-11):2017-01 VIORM = 849 VPEAK (working voltage) Enable or disable refresh (low speed output correctness check) Operating temperature range: −40°C to +125°C 28-lead, wide-body, finer pitch SOIC_W_FP package with 8.3 mm creepage and clearance or 6 mm × 6 mm LFCSP package with 1.27 mm creepage and clearance

5 kV RMS/3.75 kV RMS, Dual LVDS Gigabit Isolator (0 Reverse Channels) Features: 5 kV rms and 3.75 kV rms LVDS isolators Complies with TIA/EIA-644-A LVDS standard Multiple dual-channel configurations Any data rate up to 1.1 Gbps switching with low jitter 4 ns typical propagation delay 2.6 ps rms typical random jitter, rms 90 ps typical peak-to-peak total jitter at 1.1 Gbps 2.5 V or 3.3 V supplies −75 dBc power supply ripple rejection, phase spur level Glitch immunity ±8 kV IEC 61000-4-2 ESD protection across isolation barrier High common-mode transient immunity: >25 kV/μs Passes EN 55022 Class B radiated emissions limits with 1.1 Gbps PRBS Safety and regulatory approvals (20-lead SOIC_W package) UL (pending): 5000 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) VDE certificate of conformity (pending) DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 424 VPEAK Fail-safe output high for open, short, and terminated input conditions (ADN4655/ADN4656) Operating temperature range: −40°C to +125°C 7.8 mm minimum creepage and clearance

5 kV RMS/3.75 kV RMS, Dual LVDS Gigabit Isolator (Second Channel Reversed) Features: 5 kV rms and 3.75 kV rms LVDS isolators Complies with TIA/EIA-644-A LVDS standard Multiple dual-channel configurations Any data rate up to 1.1 Gbps switching with low jitter 4 ns typical propagation delay 2.6 ps rms typical random jitter, rms 90 ps typical peak-to-peak total jitter at 1.1 Gbps 2.5 V or 3.3 V supplies −75 dBc power supply ripple rejection, phase spur level Glitch immunity ±8 kV IEC 61000-4-2 ESD protection across isolation barrier High common-mode transient immunity: >25 kV/μs Passes EN 55022 Class B radiated emissions limits with 1.1 Gbps PRBS Safety and regulatory approvals (20-lead SOIC_W package) UL (pending): 5000 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) VDE certificate of conformity (pending) DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 424 VPEAK Fail-safe output high for open, short, and terminated input conditions (ADN4655/ADN4656) Operating temperature range: −40°C to +125°C 7.8 mm minimum creepage and clearance

Dual, 3 V, CMOS, LVDS High Speed Differential Driver Features:15 kV ESD protection on output pins600 Mbps (300 MHz) switching ratesFlow-through pinout simplifies PCB layout300 ps typical differential skew700 ps maximum differential skew1.5 ns maximum propagation delay3.3 V power supply355 mV differential signalingLow power dissipation: 23 mW typicalInteroperable with existing 5 V LVDS receiversConforms to TIA/EIA-644 LVDS standardIndustrial operating temperature range (40C to +85C)

250 Mbps, Half Duplex, Quad M-LVDS Transceivers Features: Four M-LVDS transceivers (driver and receiver pairs) Switching rate: 250 Mbps (125 MHz) Independent pin select for each receiver, two modes: Type 1: input hysteresis of 15 mV typical Type 2: differential input threshold voltage offset by 100 mV to support open-circuit, short-circuit, and bus idle fail-safe Compatible with the TIA/EIA-899 standard for M-LVDS Glitch free power-up/power-down on the M-LVDS bus Controlled transition times on the driver output Common-mode range: −1 V to +3.4 V, allowing communication with ±2 V of ground noise Driver outputs high-Z when disabled or powered off Independent enable pins for each driver and receiver Enhanced ESD protection on bus pins ≥±15 kV HBM, air discharge ≥±8 kV HBM, contact discharge ≥±10 kV IEC 61000-4-2, air discharge ≥±8 kV IEC 61000-4-2, contact discharge Enhanced ±8 kV HBM ESD protection for all pins, contact discharge Operating temperature range: −40°C to +105°C Available in 48-lead, 7 mm x 7 mm LFCSP

Two-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates two isolated, well regulated independent outputs VOUT1: 24 V or 6 V to 28 V VOUT2: 3.3 V, 5.0 V, or 5.15 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback and buck regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three 100 kbps general-purpose isolated data channels 41-lead, 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Safety and regulatory approvals (pending) CISPR11 Class B radiated emission UL recognition: 2500 V rms for 1 minute duration per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

SPI/Digital or I2C Module Isolator with Fixed 5V and Adjustable 5V Regulated Power Features: 6-Channel Logic Isolator: 2500VRMS for 1 Minute UL-CSA Recognized File #E151738 Isolated DC Power: 3V to 5V Adjustable at Up to 100mA ±5V Fixed at Up to 100mA No External Components Required SPI/Digital (LTM2886-S) or I2C (LTM2886-I) Options High Common Mode Transient Immunity: 30kV/μs High Speed Operation: 10MHz Digital Isolation 4MHz/8MHz SPI Isolation 400kHz I2C Isolation 3.3V (LTM2886-3) or 5V (LTM2886-5) Operation 1.62V to 5.5V Logic Supply ±10kV ESD HBM Across the Isolation Barrier Maximum Continuous Working Voltage: 560VPEAK Low Current Shutdown Mode (<10μA) Low Profile (15mm × 11.25mm × 3.42mm) BGA Package

isoSPI Isolated Communications Interface Features: AEC-Q100 Qualified for Automotive Applications 1Mbps Isolated SPI Data Communications Simple Galvanic Isolation Using Standard Transformers Bidirectional Interface Over a Single Twisted Pair Supports Cable Lengths Up to 100 Meters Very Low EMI Susceptibility and Emissions Configurable for High Noise Immunity or Low Power Engineered for ISO26262 Compliant Systems Requires No Software Changes in Most SPI Systems Ultralow, 2µA Idle Current Automatic Wake-Up Detection Operating Temperature Range: –40°C to 125°C 2.7V to 5.5V Power Supply Interfaces to All Logic from 1.7V to 5.5V Available in 16-Lead QFN and MSOP Packages

SPI/Digital or I2C Module Isolator Features: 6-Channel Logic Isolator: 3500VRMS for 1 Minute UL-CSA Recognized File #E151738 3V to 5.5V Supply Operation No External Components Required SPI/Digital (LTM2892-S) or I2C (LTM2892-I) Options High Common Mode Transient Immunity: 50kV/μs High Speed Operation: 10MHz Digital Isolation 4MHz/8MHz SPI Isolation 400kHz I2C Isolation Operation Up to 125°C (H-Grade) 1.62V to 5.5V Logic Supplies for Flexible Digital Interfacing ±15kV ESD HBM Across the Isolation Barrier Maximum Continuous Working Voltage: 850VPEAK Low Current Shutdown Mode (<10μA) Small (9mm × 6.25mm × 2.91mm) BGA Package