5.7 kV RMS 500kbps Half Duplex Signal and Power Isolated RS-485 Transceiver with 15 kV IEC ESD Features: 5.7 kV rms isolated RS-485/RS-422 transceiver Low radiated emissions, integrated, isolated dc-to-dc converter Passes EN 55032 Class B with margin on a 2-layer PCB Cable invert smart feature Correct reversed cable connection on A, B, Y, and Z bus pins while maintaining full receiver fail-safe feature ESD protection on RS-485 A, B, Y, and Z pins 12 kV IEC61000-4-2 contact discharge 15 kV IEC61000-4-2 air discharge High speed 25 Mbps data rate (ADM2865E/ADM2867E) Low speed 500 kbps data rate for EMI control (ADM2861E/ADM2863E) Flexible power supplies Input VCC supply of 3 V to 5.5 V Logic VIO supply of 1.7 V to 5.5 V VSEL pin to select VISO supply of 5 V (VCC > 4.5 V) or 3.3 V PROFIBUS compliant for 5 V VISO Wide operating temperature range: −40°C to +105°C High common-mode transient immunity: 250 kV/μs Short-circuit, open-circuit, and floating input receiver fail-safe Supports 192 bus nodes (72 k receiver input impedance) Full hot swap support (glitch free power-up/power-down) Safety and regulatory approvals (pending) CSA Component Acceptance Notice 5A, DIN V VDE V 0884-11, UL 1577, CQC11-471543-2012, IEC 61010-1 Complies with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E) 28-lead, fine pitch SOIC_W package (10.15 mm 10.05 mm) with >8.0 mm creepage and clearance

5.7 kV RMS 500kbps Full Duplex Signal and Power Isolated RS-485 Transceiver with 15 kV IEC ESD Features: 5.7 kV rms isolated RS-485/RS-422 transceiver Low radiated emissions, integrated, isolated dc-to-dc converter Passes EN 55032 Class B with margin on a 2-layer PCB Cable invert smart feature Correct reversed cable connection on A, B, Y, and Z bus pins while maintaining full receiver fail-safe feature ESD protection on RS-485 A, B, Y, and Z pins 12 kV IEC61000-4-2 contact discharge 15 kV IEC61000-4-2 air discharge High speed 25 Mbps data rate (ADM2865E/ADM2867E) Low speed 500 kbps data rate for EMI control (ADM2861E/ADM2863E) Flexible power supplies Input VCC supply of 3 V to 5.5 V Logic VIO supply of 1.7 V to 5.5 V VSEL pin to select VISO supply of 5 V (VCC > 4.5 V) or 3.3 V PROFIBUS compliant for 5 V VISO Wide operating temperature range: −40°C to +105°C High common-mode transient immunity: 250 kV/μs Short-circuit, open-circuit, and floating input receiver fail-safe Supports 192 bus nodes (72 k receiver input impedance) Full hot swap support (glitch free power-up/power-down) Safety and regulatory approvals (pending) CSA Component Acceptance Notice 5A, DIN V VDE V 0884-11, UL 1577, CQC11-471543-2012, IEC 61010-1 Complies with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E) 28-lead, fine pitch SOIC_W package (10.15 mm 10.05 mm) with >8.0 mm creepage and clearance

Small, 3.75 kV RMS Quad Digital Isolators (4/0 Channel Directionality) Features: Up to 25 Mbps data rate (NRZ) Low propagation delay: 25 ns typical Low dynamic power consumption 1.8 V to 5 V level translation High common-mode transient immunity: >25 kV/µs Output default select 20-lead, RoHS-compliant, SSOP package See data sheet for additional features

5.7kV rms Digital Isolator for Isolated USB 2.0 High Speed (Downstream Clock Input) Features: USB 2.0 signaling with automatic detection of low, full, and high speed connections 1.5 Mbps, 12 Mbps, and 480 Mbps data rates Bidirectional USB isolator for upstream or downstream ports Redriving and high speed data retiming for input jitter removal and an open eye Flexible clock input options 4.5 V to 5.5 V VBUSx or 3 V to 3.6 V operation on each side 21 mA typical idle, low or full speed mode supply current 48 mA typical idle, high speed mode supply current Ultra low power standby in USB 2.0 suspend (L2) or disconnect 1.7 mA typical low power standby, upstream supply current 20 μA typical low power standby, downstream supply current ±8000 V IEC 61000-4-2 ESD protection across the isolation barrier Passed CISPR32/EN55032 Class B emissions High common-mode transient immunity: 50 kV/μs typical Safety and regulatory approvals (pending) UL (pending): 5700 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) IEC 62368-1, IEC 61010-1 and IEC60601‑1 VDE certificate of conformity (pending) DIN V VDE V 0884-11 (VDE V 0884-11):2017-01 VIORM = 849 VPEAK Operating temperature range: −55°C to +125°C 20-lead, wide-body, increased creepage SOIC_IC package with 8.3 mm creepage and clearance

The ADAU1328 is a high performance, single-chip codec that provides two analog-to-digital converters (ADCs) with differential input and eight digital-to-analog converters (DACs) with single-ended output using the Analog Devices, Inc. patented multibit sigma-delta (Σ-Δ) architecture. An SPI port is included, allowing a microcontroller to adjust volume and many other parameters. The ADAU1328 operates from 3.3 V digital and analog supplies. The ADAU1328 is available in a 48-lead (single-ended output) LQFP. Other members of this family include a differential DAC output version.The ADAU1328 is designed for low EMI. This consideration is apparent in both the system and circuit design architectures. By using the on-board PLL to derive the master clock from the LR clock or from an external crystal, the ADAU1328 eliminates the need for a separate high frequency master clock and can also be used with a suppressed bit clock. The digital-to-analog and analog-to-digital converters are designed using the latest ADI continuous time architectures to further minimize EMI. By using 3.3 V supplies, power consumption is minimized, further reducing emissions.APPLICATIONS Home theater systems Set-top boxes Digital audio effects processors

The ADM3202 / ADM3222 / ADM1385 are high speed, 2-channel RS232/V.28 interface devices which operate from a single +3.3 V power supply. Low power consumption and a shutdown facility (ADM3222 / ADM1385) makes them ideal for battery powered portable instruments.The ADM3202 / ADM3222 / ADM1385 conform to the EIA-232E and CCITT V.28 specifications and operate at data rates up to 230 kbps. Four external 0.1 µF charge pump capacitors are used for the voltage doubler/inverter permitting operation from a single +3.3 V supply.The ADM3222 / ADM1385 contain additional enable and shutdown circuitry. The EN input may be used to three-state the receiver outputs. The SD input is used to power down the charge pump and transmitter outputs reducing the quiescent current to less than 1 µA. The receivers remain enabled during shutdown unless disabled using EN.The ADM3202 is available in a 16-lead DIP, narrow and wide SO as well as a space saving TSSOP package. The ADM3222 is available in 18 lead DIP , SO and in 20 lead SSOP and TSSOP. The ADM1385 is available in a 20 lead SSOP package and is pin compatible with the LTC1385 CG.

The ADM222, ADM232A, ADM242 are a family of high-speedRS-232 line drivers/receivers offering transmission rates up to200 kB/s. Operating from a single 5 V power supply, a highlyefficient on-chip charge pump using small (0.1 µF) externalcapacitors allows RS-232 bipolar levels to be developed. TwoRS-232 drivers and two RS-232 receivers are provided oneach device.The devices are fabricated on BiCMOS, an advanced mixedtechnology process that combines low power CMOS with highspeedbipolar circuitry. This allows for transmission rates up to200 kB/s, yet minimizes the quiescent power supply current tounder 5 mA.The ADM232A is a pin-compatible, high-speed upgrade for theAD232 and for the ADM232L. It is available in 16-lead DIPand in both narrow and wide surface-mount (SOIC) packages.The ADM222 contains an additional shutdown (SHDN) functionthat may be used to disable the device, thereby reducing thesupply current to 0.1 µA. During shutdown, all transmit/receivefunctions are disabled. The ADM222 is available in 18-leadDIP and in a wide surface-mount (SOIC) package.The ADM242 combines both shutdown (SHDN) and enable(EN) functions. The shutdown function reduces the supplycurrent to 0.1 mA. During shutdown, the transmitters are disabledbut the receivers continue to operate normally. Theenable function allows the receiver outputs to be disabledthereby facilitating sharing a common bus. The ADM242 isavailable in 18-lead DIP and in a wide surface-mount (SOIC)package.Applications Computers Peripherals Modems Printers Instruments

The ADM2483 differential bus transceiver is an integrated,galvanically isolated component designed for bidirectional datacommunication on balanced, multipoint bus transmission lines.It complies with ANSI EIA/TIA-485-A and ISO 8482: 1987(E).Using the iCoupler technology from Analog Devices, Inc., theADM2483 combines a 3-channel isolator, a three-state differentialline driver, and a differential input receiver into a single package.The logic side of the device is powered with either a 5 V or 3 Vsupply, and the bus side uses a 5 V supply only.The ADM2483 is slew-limited to reduce reflections withimproperly terminated transmission lines. The controlled slewrate limits the data rate to 500 kbps. The device’s input impedanceis 96 kΩ, allowing up to 256 transceivers on the bus. Its driverhas an active-high enable feature. The driver differential outputsand receiver differential inputs are connected internally to forma differential input/output (I/O) port.When the driver is disabled or when VDD1 or VDD2 = 0 V, thisimposes minimal loading on the bus. An active-high receiverdisable feature, which causes the receive output to enter a highimpedance state, is provided as well.The receiver inputs have a true fail-safe feature that ensures alogic-high receiver output level when the inputs are open orshorted. This guarantees that the receiver outputs are in aknown state before communication begins and at the pointwhen communication ends.Current limiting and thermal shutdown features protect againstoutput short circuits and bus contention situations that mightcause excessive power dissipation. The part is fully specifiedover the industrial temperature range and is available in a16-lead, wide body SOIC package.Applications Low power RS-485/RS-422 networks Isolated interfaces Building control networks Multipoint data transmission systems

The ADM2490E is an isolated data transceiver with ±8 kV ESD protection that is suitable for high speed, full-duplex communication on multipoint transmission lines. It is designed for balanced transmission lines and complies with ANSI TIA/EIA-485-A-1998 and ISO 8482: 1987(E). The device employs Analog Devices, Inc., iCoupler® technology to combine a 2-channel isolator, a three-state differential line driver, and a differential input receiver into a single package.The differential transmitter outputs and receiver inputs feature electrostatic discharge circuitry that provides protection to ±8 kV using the human body model (HBM). The logic side of the device can be powered with either a 5 V or a 3 V supply, whereas the bus side requires an isolated 5 V supply.The device has current-limiting and thermal shutdown features to protect against output short circuits and situations where bus contention could cause excessive power dissipation.The ADM2490E is available in a wide body, 16-lead SOIC package and operates over the −40°C to +105°C temperature range.Applications Isolated RS-485/RS-422 Interfaces Industrial Field Networks INTERBUS Multipoint Data Transmission Systems

The ADM307xE are 3.3 V, low power data transceivers with ±15 kV ESD protection suitable for full- and half-duplex communication on multipoint bus transmission lines. They are designed for balanced data transmission, and they comply with TIA/EIA standards: RS-485 and RS-422.The devices have a ⅛ unit load receiver input impedance, which allows up to 256 transceivers on a bus. Because only one driver should be enabled at any time, the output of a disabled or powered-down driver is tristated to avoid overloading the bus.The receiver inputs have a true fail-safe feature, which eliminates the need for external bias resistors and ensures a logic high output level when the inputs are open or shorted. This guarantees that the receiver outputs are in a known state before communication begins and when communication ceases.Applications Power/energy metering Industrial control Lighting systems Telecommunications Security systems Instrumentation