The ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 are micropower, 4-channel digital isolators based on the Analog Devices, Inc., iCoupler® technology. Combining high speed, complementary metal oxide semiconductor (CMOS) and monolithic air core transformer technologies, these isolation components provide outstanding performance characteristics superior to the alternatives, such as optocoupler devices. As shown in Figure 3 in the data sheet, in standard operating mode, when ENx = 0 (internal refresh enabled), the current per channel is less than 10 μA. When ENx = 1 (internal refresh disabled), the current per channel drops to less than 1 μA.The ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 family of quad 2.5 kV digital isolation devices are packaged in a small 16-lead QSOP and 20-lead SSOP, freeing almost 70% of board space compared to isolators packages in wide body SOIC packages.The devices withstand high isolation voltages and meet regulatory requirements, such as UL and CSA standards. In addition to the space savings, the ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 operate with supplies as low as 2.25 V.Despite the low power consumption, all models of the ADuM1440/ADuM1441/ADuM1442/ADuM1445/ADuM1446/ADuM1447 provide low, pulse width distortion at <8 ns. In addition, every model has an input glitch filter to protect against extraneous noise disturbances.APPLICATIONS General-purpose, low power multichannel isolation 1 MHz, low power peripheral interface (SPI) 4 mA to 20 mA loop process controls

The ADuM3480 / ADuM3481 / ADuM3482 are quad-channel digital isolators based on the Analog Devices, Inc.,iCoupler® technology. Combining high speed CMOS and monolithic air core transformer technology, these isolation components provide outstanding performance characteristics superior to alternatives such as optocoupler devices and other integrated couplers. With typical propagation delay reduced to 25 ns, pulse width distortion is also halved.The four channels of the ADuM3480 / ADuM3481 / ADuM3482 are available in a variety of channel configurations with two data rate grades up to 25 Mbps (see the Ordering Guide section). All models use separate core and I/O power supplies. The core operates between 3.0 V and 5.5 V, whereas the I/O supply can range from 1.8 V to 5.5 V. If operation is required within the range of the core supply, the two supplies can be tied together to allow single-supply operation. When the I/O must interface with logic levels that are different from the core supply voltage, then the I/O supply can be operated independently of the core supply over a wider range. The minimum I/O supply voltage is 1.8 V, allowing compatibility with low voltage logic. Both core and I/O supplies are required for proper operation.APPLICATIONS General-purpose multichannel isolation SPI interface/data converter isolation Industrial field bus isolation

The ADuM7640 / ADuM7641 / ADuM7642 / ADuM7643 are 6-channel digital isolators based on the Analog Devices, Inc., iCoupler® technology. These 1 kV digital isolation devices are packaged in a small 20-lead QSOP. They offer space savings and a lower price than 2.5 kV or 5 kV isolation solutions when only functional isolation is needed.This family, like many Analog Devices isolators, offers very low power consumption, using one-tenth to one-sixth the power of other digital isolators, with the supply voltage on either side ranging from 3.0 V to 5.5 V. Despite their low power consumption, the ADuM7640 / ADuM7641 / ADuM7642 / ADuM7643 provide low pulse width distortion (< 6 ns for C grade) and a channel-by-channel glitch filter to protect the device against extraneous noise disturbances. Four channel direction combinations areavailable with a maximum data rate of 1 Mbps or 25 Mbps. Allproducts have a default output high logic state in the absence of input power.APPLICATIONS General-purpose, multichannel isolation SPI interface/data converter isolation RS-232/RS-422/RS-485 transceivers Industrial field bus isolation

The ADV7282 / ADV7282-M are versatile one-chip, multiformat video decoders. The ADV7282 / ADV7282-M automatically detects standard analog baseband video signals compatible with worldwide NTSC, PAL, and SECAM standards in the form of composite, S-Video, and component video.The ADV7282 converts the analog video signals into a YCrCb 4:2:2 video data stream that is compatible with the 8-bit ITU-R BT.656 interface standard.The ADV7282-M converts the analog video signals into an 8-bit YCrCb 4:2:2 video data stream that is output over a mobile industry processor interface (MIPI®) CSI-2 interface.The analog video inputs of the ADV7282/ADV7282-M accept single-ended, pseudo differential, and fully differential signals. The ADV7282 / ADV7282-M contain a deinterlacer (I2P converter) and short to battery detection capability with two STB diagnostic pins. The ADV7282 provides four analog inputs. The ADV7282-M provides six analog inputs and three general-purpose outputs.The ADV7282 / ADV7282-M are programmed via a 2-wire, serial bidirectional port (I2C compatible) and is fabricated in a 1.8 V CMOS process. The LFCSP package option makes the decoder ideal for space-constrained portable applications.APPLICATIONS Smartphone/multimedia handsets Automotive infotainment DVRs for video security Media players

The ADV7282 / ADV7282-M are versatile one-chip, multiformat video decoders. The ADV7282 / ADV7282-M automatically detects standard analog baseband video signals compatible with worldwide NTSC, PAL, and SECAM standards in the form of composite, S-Video, and component video.The ADV7282 converts the analog video signals into a YCrCb 4:2:2 video data stream that is compatible with the 8-bit ITU-R BT.656 interface standard.The ADV7282-M converts the analog video signals into an 8-bit YCrCb 4:2:2 video data stream that is output over a mobile industry processor interface (MIPI®) CSI-2 interface.The analog video inputs of the ADV7282/ADV7282-M accept single-ended, pseudo differential, and fully differential signals. The ADV7282 / ADV7282-M contain a deinterlacer (I2P converter) and short to battery detection capability with two STB diagnostic pins. The ADV7282 provides four analog inputs. The ADV7282-M provides six analog inputs and three general-purpose outputs.The ADV7282 / ADV7282-M are programmed via a 2-wire, serial bidirectional port (I2C compatible) and is fabricated in a 1.8 V CMOS process. The LFCSP package option makes the decoder ideal for space-constrained portable applications.APPLICATIONS Smartphone/multimedia handsets Automotive infotainment DVRs for video security Media players

The SSM3302 is a fully integrated, high efficiency, stereo Class-D audio amplifier. The application circuit requires minimal externalcomponents and operates from a single 7 V to 18 V supply. The device is capable of delivering 2 × 10 W of continuous output power into a 4 Ω load (or 2 × 8 W into 8 Ω) with 98 dB. Spread spectrum pulse density modulation (PDM) is used toprovide lower EMI radiated emissions compared with other Class-D architectures. The SSM3302 includes an optional modulation select pin (ultralow EMI emission mode) that significantly reduces the radiated emissions at the Class-D outputs, particularly above 100 MHz. The SSM3302 can pass FCC Class-B emissions testing with an unshielded 20 inch cable using common-mode choke-based filtering.The fully differential input of the SSM3302 provides excellent rejection of common-mode noise on the input. The device also includes a highly flexible gain select pin that only requires one series resistor to choose a gain between 9 dB and 24 dB, with no change to the input impedance. The benefit of this is to improve gain matching between multiple SSM3302 devices within a single application compared with using external resistors to set gain.The SSM3302 includes an integrated voltage regulator thatgenerates a 5 V rail.The SSM3302 has a micropower shutdown mode with a typical shutdown current of 10 μA. Shutdown is enabled by applying a logic low to the SD pin. The device also includes pop-and-click suppression circuitry that minimizes voltage glitches at the output during turn on and turn off, reducing audible noise during activation and deactivation.Other included features to simplify system level integration of the SSM3302 are input low-pass filtering to suppress out-ofband DAC noise interference to the pulse density modulator, fixed input impedance to simplify component selection across multiple platform production builds, and a thermal warning indicator pin.The SSM3302 is specified over the commercial temperaturerange (−40°C to +85°C). It has built-in thermal shutdown andoutput short-circuit protection. It is available in a halide-free,40-lead, 6 mm × 6 mm lead frame chip scale package (LFCSP).APPLICATIONS Mobile computing Flat panel televisions Media docking stations Portable electronics Sound bars

SigmaDSP Compact Digital Audio Processor with Extended Internal Memory Features: Qualified for automotive applications High performance SigmaDSP core enables low latency and audio applications Active Noise Cancellation (ANC) Echo-Canceller and Noise Reduction (ECNR) Surround sound algorithms Features SigmaStudio, a proprietary graphical Integrated Development Environment (IDE), for the development of custom signal flows Comprehensive Toolbox of pre-defined building blocks Faster design time with proven solutions Intuitive system design 294.912 MHz, 32-bit SigmaDSP core at 1.2 V 24 kWords of program memory 80 kWords of parameter/data RAM 6144 SIMD instructions per sample at 48 kHz 1600 ms digital audio delay pool at 48 kHz Audio I/O and routing 4 serial input ports, 4 serial output ports 48-channel, 32-bit digital I/O up to a sample rate of 192 kHz Flexible configuration of I2S, left and right justified, and up to 16-channel TDM formats on serial data pins 8 stereo ASRCs from 1:8 up to 7.75:1 ratio and 139 dB dynamic range Stereo S/PDIF input and output at 192 kHz Four PDM microphone input channels Multichannel, byte addressable TDM serial ports Clock oscillator for generating master clock from crystal Integer PLL and flexible clock generators Integrated die temperature sensor I2C and SPI control interfaces (both slave and master) Standalone operation Self-boot from serial EEPROM 6-channel, 10-bit SAR auxiliary control ADC 14 multipurpose pins for digital controls and outputs On-chip regulator for generating 1.2 V from 1.8 V to 3.3 V supply 72-lead, 10 mm × 10 mm LFCSP package with 5.3 mm exposed pad Temperature range: −40°C to +105°C

Three ADCs, One DAC, Low Power Codec with Audio DSPs Features: Programmable FastDSP audio processing engine Up to 768 kHz sample rate Biquad filters, limiters, volume controls, mixing Tensilica HiFi 3z DSP core Quad MAC per cycle: 24 x 24-bit multiplier and 64-bit accumulator Flexible power operation mode: 24.576 MHz, 49.152 MHz, 73.728 MHz, and 98.304 MHz 336 kB total memory JTAG debug and trace Low latency, 24-bit ADCs and DAC 106 dB SNR (signal through ADC with A-weighted filter) 110 dB combined SNR (signal through DAC and headphone with A-weighted filter) Programmable double precision MAC engine for maximum 24-stage equalizer Serial port sample rates from 8 kHz to 768 kHz 5 μs group delay (fS = 768 kHz) analog in to analog out with FastDSP bypass (zero instructions) 3 differential or single-ended analog inputs, configurable as microphone or line inputs 8 digital microphone inputs Analog differential audio output, configurable as either line output or headphone drive 2 PDM output channels PLL supporting any input clock rate from 30 kHz to 36 MHz 4 channel asynchronous sample rate converters (ASRCs) 2, 16-channel serial audio ports supporting I2S, left justified, right justified, or up to TDM16 (TDM12 in Turbo mode) 8 interpolators and 8 decimators with flexible routing Power supplies Analog AVDD at 1.8 V typical Digital I/O IOVDD at 1.1 V to 1.98 V Digital DVDD at 0.85 V to 1.21 V Headphone HPVDD at 1.8 V typical Headphone HPVDD_L at 1.2 V to HPVDD Control/communication interfaces I2C, SPI, or UART control ports Master quad SPI (QSPI) UART communication port Self-boot from QSPI flash Flexible GPIO and IRQ 56-ball, 0.35 mm pitch, 2.980 mm × 2.679 mm WLCSP

Stereo PDM to I2S/TDM Converter Features: 2 channels of PDM audio inputs from digital microphones 64× decimation ratio of PDM to PCM audio data 24-bit resolution to support high sound pressure level (SPL) microphones 126 dB A-weighted SNR 4 kHz to 96 kHz output sampling rate Bit clock rates of 64×, 128×, 192×, 256×, 384×, or 512× the output sampling rate Automatic PDM clock generation Automatic power-down when BCLK is removed 0.36 mA DVDD operating current at 48 kHz sampling rate and 1.8 V supply Slave I2S or TDM output interface Up to TDM-16 supported Configurable TDM slots I/O supply voltage from 1.70 V to 3.63 V DVDD core supply voltage from 1.10 V to 1.98 V 4 μA typical DVDD shutdown current 9-ball, 1.26 mm × 1.26 mm, 0.4 mm pitch WLCSP Power-on reset

2, 31.76 W, Digital Input, Filterless Stereo Class D Audio Amplifier Features: Digital input stereo, high efficiency Class-D amplifier Operates from a single 4.5 V to 16.5 V supply State-of-the-art, proprietary, filterless - modulation 106.5 dB SNR at PO = 8.1 W, RL = 8 , AV = 19 dB, PVDD = 12 V, A weighted 0.004% THD + N at 5 W into 8 38.5 V rms output voltage noise, f = 20 Hz to 20 kHz, A weighted, PVDD = 16 V, 8 Pop and clickless on and off sequence 2 14.67 W output at 12 V supply to 4 loads at <1% THD + N 2 14.4 W output at 16 V supply to 8 loads at <1% THD + N Mono mode for increased maximum output power 1 49.69 W output at 16 V supply to 2 loads at <1% THD + N Support for low impedance loads As low as 3 Ω/5 μH in stereo mode As low as 2 Ω/5 μH in mono mode High power efficiency 93.8% efficiency into an 8 Ω load 90.6% efficiency into a 4 Ω load 12.34 mA quiescent current with single 12 V PVDD supply Single-supply operation with internal LDOs or option to use an external 5 V and 1.8 V supply for lowest power consumption I2C control and hardware modes with up to 16 pin-selectable slots/addresses Supported sample rates from 8 kHz to 192 kHz with 24-bit resolution Multiple PCM audio serial data formats TDM slave with support for up to 16 devices on a single bus I2S or left justified slave Adjustable full-scale output tailored for many PVDD sources 2- and 3-cell Li-Ion batteries Digital volume control with selectable smooth ramp Automatic power-down function Supply monitoring automatic gain control (AGC) function reduces system brownout Standalone operational mode without I2C Temperature sensor with 1°C step readout via I2C Short-circuit, undervoltage, and thermal protection Thermal early warning Power-on reset PVDD sensing ADC 40-lead, 6 mm × 6 mm LFCSP with thermal pad