8 Channel, 12-Bit, Configurable ADC/DAC with on-chip Reference, SPI interface Features: Download AD5592R-1-KGD Data Sheet. Available as Known Good Die and fully guaranteed to data sheet specifications. 8-channel, configurable ADC/DAC/GPIO Configurable as any combination of 8 × 12-bit DAC channels 8 × 12-bit ADC channels 8 × general-purpose digital input/output pins Integrated temperature sensor SPI interface Available in 16-ball, 2 mm × 2 mm WLCSP 16-lead, 3 mm × 3 mm LFCSP 16-lead TSSOP

3-Phase Metrology IC for Polyphase Shunt Meters Features: Enables shunt current sensors in polyphase energy meters Immune to magnetic tampering Highly accurate; supports EN 50470-1, EN 50470-3, IEC 62053-21, IEC 62053-22, IEC 62053-23, ANSI C12.20, and IEEE 1459 standards Compatible with 3-phase, 3- or 4-wire (delta or wye) meters and other 3-phase services Computes active, reactive, and apparent energy on each phase and on the overall system Less than 0.2% error in active and reactive energy over a dynamic range of 2000 to 1 at TA = 25°C Less than 0.1% error in voltage rms over a dynamic range of 500 to 1 at TA = 25°C Less than 0.25% error in current rms over a dynamic range of 500 to 1 at TA = 25°C Power quality measurements including THD Single 3.3 V supply Operating temperature: −40°C to +85°C Flexible I2C, SPI, and HSDC serial interfaces Safety and regulatory approvals UL recognition 5000 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice #5A IEC 61010-1: 400 V rms VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 846 V peak Optional isolated (ADE7933/ADE7932) or nonisolated (ADE7923) neutral

Robust, Industrial, Low Power 10BASE-T1L Ethernet PHY Features: 10BASE-T1L IEEE Standard 802.3cg-2019 compliant Supports 1.0 V p-p and 2.4 V p-p transmit levels Supports intrinsic safety applications Cable Reach 1700 meters with 1.0 V p-p 1700 meters with 2.4 V p-p Low power consumption Single supply 1 V p-p: 45 mW typical Dual supply 1 V pk-pk: 39 mW typical Diagnostics Frame generator and checker Multiple loopback modes IEEE test mode support Link and cable diagnostics MII, RMII and RGMII MAC interfaces MDIO Management Interface Single or dual supply with 1.8 V or 3.3 V operation Unmanaged configuration using pin strapping including 25 MHz crystal or external clock input (50 MHz for RMII) 3.3 V, 2.5 V, or1.8 V MAC interface VDDIO supply Integrated power supply monitoring and POR EMC test standards IEC 61000-4-4 EFT (±4 kV) IEC 61000-4-2 ESD (±4 kV contact discharge) IEC 61000-4-2 ESD (±8 kV air discharge) IEC 61000-4-5 surge (±4 kV) IEC 61000-4-6 conducted immunity (10 V/m) IEC 61000-4-3 radiated immunity (Class A) EN 55032 radiated emissions (Class B) Small package 40-lead (6 mm x 6 mm) LFCSP Temperature range Industrial: -40°C to +85°C Extended:-40°C to +105°C

Robust, Industrial, Low Power 10BASE-T1L Ethernet MAC-PHY Features: 10BASE-T1L IEEE Standard 802.3cg-2019 compliant Integrated MAC with SPI interface SPI supporting 10 Mbps full duplex Supports OPEN Alliance 10BASE-T1x MAC-PHY serial interface Low power consumption: dual supply 42 mW typical Supports 1.0 V p-p and 2.4 V p-p transmit levels Autonegotiation capability Supports intrinsic safety applications External termination resistors Separate receive and transmit pins MDIO memory map accessible via SPI On Chip FIFOs: 20kB receive, 8kB transmit (configurable) Cut-through or Store and forward operation Rx high and low priority queues IEEE 1588 timestamp support Statistics counters 16 MAC addresses supported for frame filtering Link LED Unmanaged configuration using pin strapping including: Master/Slave selection Transmit amplitude 25 MHz crystal oscillator/25 MHz external clock input Single supply 1.8 V/3.3 V operation (mode dependent) Cable Reach 1700 meters with 1.0 V p-p 1700 meters with 2.4 V p-p EMC test standards IEC 61000-4-4 electrical fast transient (EFT) (±4 kV) IEC 61000-4-2 ESD (±4 kV contact discharge) IEC 61000-4-2 ESD (±8 kV air discharge) IEC 61000-4-6 conducted immunity (10V/m) IEC 61000-4-5 surge (±4kV) IEC 61000-4-3 radiated immunity (Class A) EN55032 radiated emissions (Class B) Small package 40-lead (6 mm × 6 mm) LFCSP Wide temperature range -40°C to 105°C

Robust, Industrial, Low Latency and Low Power 10 Mbps, 100 Mbps, and 1 Gbps Ethernet PHY Features: 10BASE-Te/100BASE-TX/1000BASE-T IEEE® 802.3™ compliant MII, RMII, and RGMII MAC interfaces 1000BASE-T RGMII latency transmit < 68 ns, receive < 226 ns 100BASE-TX MII latency transmit< 52 ns, receive < 248 ns EMC test standards IEC 61000-4-5 surge (±4 kV) IEC 61000-4-4 electrical fast transient (EFT) (±4 kV) IEC 61000-4-2 ESD (±6 kV contact discharge) IEC 61000-4-6 conducted immunity (10 V) EN55032 radiated emissions (Class A) EN55032 conducted emissions (Class A) Unmanaged configuration using multilevel pin strapping EEE in accordance with IEEE 802.3az Start of packet detection for IEEE 1588 time stamp support Enhanced link detection Configurable LED Crystal oscillator frequency/25 MHz clock input frequency (50 MHz for RMII) 25 MHz/125 MHz synchronous clock output Small package and wide temperature range 40-lead, 6 mm × 6 mm LFCSP Specified for −40°C to +105°C ambient operation Low power consumption 330 mW for 1000BASE-T 140 mW for 100BASE-TX 3.3 V/2.5 V/1.8 V MAC interface VDDIO supply Integrated power supply monitoring and POR

Low Complexity, 2-Port Ethernet Switch with Integrated 10BASE-T1L PHYs Features: 10BASE-T1L IEEE® Std 802.3cg-2019™ compliant Supports 1.0 V p-p & 2.4 V p-p transmit Levels Cable reach Up to 1700 meters with 1.0 V p-p transmit level Up to 1700 meters with 2.4 V p-p transmit level Low power consumption Low power consumption - single supply 80 mW typ Dual supply 1.0 V p-p: 77 mW typical Integrated switch with SPI interface 10 Mbps full duplex 16 MAC addresses supported for frame forwarding Supports OPEN Alliance 10BASE-T1x MACPHY SPI MDIO memory map accessible via SPI Supports high & low priority queues Total buffer memory of 28 kB shared between ports and host Autonegotiation capability Managed or unmanaged configuration Cut through or store and forward operation IEEE 1588 time stamp capture on transmit and receive Diagnostics Frame generator and checker Multiple loopback modes IEEE test mode support Port dedicated statistics counters Link and cable diagnostics 25 MHz crystal or external clock input Single or dual supply with 1.8 V or 3.3 V operation Integrated power supply monitoring and POR Small package: 48-lead, 7 mm × 7 mm LFCSP Temperature range Industrial: 40°C to +85°C Extended: 40°C to +105°C

RapID Platform Generation 2 (RPG2) Network Interface Features: Configurable industrial protocol support PROFINET RT (Class B) PROFINET IRT (Class C): coming soon EtherNet/IP with DLR EtherCAT All protocols precertified Configurable applications processor interface UART: 115,200 bps to 1,000,000 bps Ethernet at 10 Mbps or 100 Mbps SPI follower: 10 MHz maximum clock I2C, QSPI, and CAN: future option Industrial Ethernet interface-compliant to IEEE 802.3, 10Base or 100Base transmit half and full duplex Single 3.3 V power supply, 840 mW Cycle time down to 1 ms (cycle times vary based on protocol, link type, and application data) 194-ball chip-scale package BGA form factor RoHS 3 compliant –40°C to +85°C industrial temperature range

24 GHz to 44 GHz, Wideband, Microwave Upconverter Features: Wideband RF input frequency range: 24 GHz to 44 GHz 2 upconversion modes Direct conversion from baseband I/Q to RF Single-sideband upconversion from real IF LO input frequency range: 5.4 GHz to 10.25 GHz LO quadrupler for up to 41 GHz Matched 50 single-ended RF output and IF inputs Option between matched 100 balanced or 50 single-ended LO inputs 100 balanced baseband inputs Sideband suppression and carrier feedthrough optimization Variable attenuator for transceiver power control Programmable via 4-wire SPI interface 40-terminal land grid array package (LGA)

MicroConverter, 12-Bit ADCs and DACs with Embedded 62 kBytes Flash MCU Features: ANALOG I/O 8-channel, 247 kSPS 12-bit ADC DC performance: ±1 LSB INL AC performance: 71 dB SNR DMA controller for high speed ADC-to-RAM capture 2 12-Bit (monotonic) voltage output DACs Dual output PWM/Σ-Δ DACs On-chip temperature sensor function ±3C On-chip voltage reference Memory 62 kBytes on-chip Flash/EE program memory 4 kBytes on-chip Flash/EE data memory Flash/EE, 100 yr retention, 100 kCycles endurance 2304 bytes on-chip data RAM 8051 based core 8051 compatible instruction set (16 MHz max) 12 interrupt sources, 2 priority levels Dual data pointer Extended 11-bit stack pointer See data sheet for additional features

Dual-Channel Digital Isolators, 5 kV Features: Qualified for automotive applications High isolation voltage: 5000 V rms Enhanced system-level ESD performance per IEC 61000-4-x 3.3 V/5 V level translation High temperature operation: 125°C High data rate: dc to 10 Mbps (NRZ) See Data Sheet for Additional Information