18-Bit, 15 MSPS, Module Data Acquisition Solution Features: Integrated fully differential ADC driver with signal scaling Wide input common-mode voltage range High common-mode rejection Single-ended to differential conversion Pin selectable input range with overrange Input ranges with 4.096 V REFBUF: ±10 V, ±5 V, ±4.096 V, ±2.5 V, and ±1.5 V Gain/attenuation options: 0.37, 0.73, 0.87, 1.38, and 2.25 Critical passive components 0.005% precision matched resistor array for FDA 9 mm × 9 mm, 0.8 mm pitch, 100-ball CSP_BGA package 2.5× footprint reduction vs. discrete solution Low power, dynamic power scaling, power-down mode 143 mW typical at 15 MSPS Throughput: 15 MSPS, no pipeline delay INL error: ±3.1 ppm typical, ±6.2 ppm maximum (Gain = 0.73, gain = 0.87, gain = 1.38, gain = 2.25) SINAD: 90.4 dB typical at 20 kHz (gain = 0.73) THD: −117 dB at 1 kHz, −110 dB at 100 kHz (gain = 0.73) Gain error: ±0.005%FS typical Gain error drift: ±0.13 ppm/°C typical On-board reference buffer with VCMO generation Serial LVDS interface Wide operating temperature range: −40°C to +85°C

ADC, 24BIT, LFCSP-16, -40 TO 85DEG C ROHS COMPLIANT: YES

The AD8363 is a true rms responding power detector that can be directly driven with a single-ended 50 Ω source. This feature makes the AD8363 frequency versatile by eliminating the need for a balun or any other form of external input tuning for operation up to 6 GHz. The AD8363 provides an accurate power measurement, independent of waveform, for a variety of high frequency communication and instrumentation systems. Requiring only a single supply of 5 V and a few capacitors, it is easy to use and provides high measurement accuracy. The AD8363 can operate from arbitrarily low frequencies to 6 GHz and can accept inputs that have rms values from less than −50 dBm to at least 0 dBm, with large crest factors exceeding the requirements for accurate measurement of WiMAX, CDMA, W-CDMA, TD-SCDMA, multicarrier GSM, and LTE signals.The AD8363 can determine the true power of a high frequency signal having a complex low frequency modulation envelope, or it can be used as a simple low frequency rms voltmeter. The high-pass corner generated by its internal offset-nulling loop can be lowered by a capacitor added on the CHPF pin.Used as a power measurement device, VOUT is connected to VSET. The output is then proportional to the logarithm of the rms value of the input. The reading is presented directly in decibels and is conveniently scaled to 52 mV/dB, or approximately 1 V per decade; however, other slopes are easily arranged. In controller mode, the voltage applied to VSET determines the power level required at the input to null the deviation from the setpoint. The output buffer can provide high load currents.The AD8363 has 1.5 mW power consumption when powered down by a logic high applied to the TCM2/PWDN pin. It powers up within about 30 μs to its nominal operating current of 60 mA at 25°C. The AD8363 is available in a 4 mm × 4 mm 16-lead LFCSP for operation over the −40°C to +125°C temperature range.A fully populated RoHS-compliant evaluation board is also available.Applications:Power amplifier linearization/control loopsMulti-Standard, Multi-Carrier Wireless Infrastructure (MCGSM, CDMA,WCDMA, TD-SCDMA, WiMAX, LTE)Transmitter power controls Transmitter signal strength indication (TSSI)RF instrumentation

4 Channel Digital Isolator 1kV

Nonvolatile, I2C Compatible 256-Position, Digital Potentiometer Features: Nonvolatile memory maintains wiper settings 256-position Thin LFCSP-10 (3 mm x 3 mm x 0.8 mm) package Compact MSOP-10 (3 mm × 4.9 mm × 1.1 mm) package I2C-compatible interface VLOGIC pin provides increased interface flexibility End-to-end resistance 5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ Resistance tolerance stored in EEPROM (0.1% accuracy) Power-on EEPROM refresh time < 1ms Software write protect command Address Decode Pin AD0 and Pin AD1 allow 4 packages per bus 100-year typical data retention at 55°C Wide operating temperature −40°C to +125°C 3 V to 5 V single supply

High Performance Fourth Generation DSP Features: 400 MHz core clock speed 3 Mbits of on-chip RAM FIR, IIR, and FFT accelerators 16-bit wide SDR SDRAM external memory interface Digital Applications Interface (DAI) enabling user-definable access to peripherals including an S/P DIF Tx/Rx, and 8-channel asynchronous sample rate converter Fully enhanced DMA engine including scatter/gather DMA, delay line DMA 8 serial ports (SPORTs) supporting I2S, left-justified sample pair, DSP Serial and TDM modes 2 SPI-compatible ports supporting master and slave modes UART and Two-Wire Interface 16 Pulse Width Modulation (PWM) channels 3 full-featured timers 176 ld LQFP EPAD and 100 ld LQFP EPAD packages Commercial and Industrial temperature ranges

High Performance Fourth Generation DSP Features: 400 MHz core clock speed 3 Mbits of on-chip RAM FIR, IIR, and FFT accelerators 16-bit wide SDR SDRAM external memory interface Digital Applications Interface (DAI) enabling user-definable access to peripherals including an S/P DIF Tx/Rx, and 8-channel asynchronous sample rate converter Fully enhanced DMA engine including scatter/gather DMA, delay line DMA 8 serial ports (SPORTs) supporting I2S, left-justified sample pair, DSP Serial and TDM modes 2 SPI-compatible ports supporting master and slave modes UART and Two-Wire Interface 16 Pulse Width Modulation (PWM) channels 3 full-featured timers 176 ld LQFP EPAD and 100 ld LQFP EPAD packages Commercial and Industrial temperature ranges

256-/1024-Position, Digital Potentiometers with Maximum 1% R-Tolerance Error and 20-TP Memory Features: Single-channel, 256-/1024-position resolution 20 kΩ, 50 kΩ, and 100 kΩ nominal resistance Maximum ±1% nominal resistor tolerance error (resistor performance mode) 20-times programmable wiper memory Rheostat mode temperature coefficient: 35 ppm/°C Voltage divider temperature coefficient: 5 ppm/°C +9 V to +33 V single-supply operation ±9 V to ±16.5 V dual-supply operation SPI-compatible serial interface Wiper setting readback Power-on refreshed from 20-TP memory

ADUM1410 - Quad-Channel Digital Isolators

ETHERNET CONTROLLER, 100MBPS, BGA-144; Data Rate:100Mbps; Ethernet Type:-; Supply Voltage Min:4.75V; Supply Voltage Max:34V; Controller IC Case Style:BGA; No. of Pins:144Pins; IC Interface Type:I2C, SPI; Operating Temperature Min:-40°C; Operating Temperature Max:125°C; Product Range:EtherCAT® Slave Controllers; Automotive Qualification Standard:-; MSL:MSL 3 - 168 hours; SVHC:No SVHC (27-Jun-2018)