Low Noise, High Efficiency Charge Pump for White LEDs Features: Low Noise Constant Frequency Operation 25% Less Input Current Than Doubler Charge Pump High Output Current: Up To 125mA Small Application Circuit Regulated Output Voltage or Current Automatic Soft-Start VIN Range: 2.7V to 4.5V No Inductors 1.5MHz Switching Frequency ICC < 1µA in Shutdown Available in 10-Pin MSOP and 3mm x 3mm DFN Packages 

500mA Camera LED Charge Pump Features: Low Noise Constant Frequency Operation High Efficiency: Up to 94% Multi-Mode Operation: 1x, 1.5x or 2x Boost Modes Automatic Mode Switching High Output Current: Up to 500mA Tiny Application Circuit (3mm × 3mm DFN Package All Components <1mm High) Automatic Soft-Start Output Disconnect Open, Shorted LED Protection No Inductors Internal 110m LED Current Sense Resistor 3mm × 3mm 10-Lead DFN Package

16-Channel 50mA LED Driver with Buck Controller Features: 6V to 55V Power Input Voltage Range 16 Independent LED Outputs Up to 75mA/36V ±3% LED Current Matching at 50mA (Typ ±1%) 6-Bit Dot Correction Current Adjustment 12-Bit Grayscale PWM Dimming 0.5μs Minimum LED On-Time Adaptive LED Bus Voltage for High Efficiency Cascadable 30MHz Serial Data Interface Full Diagnostic and Protection: Individual Open/Short LED and Overtemperature Fault 40-Lead 6mm × 6mm QFN Package

White LED Driver with Integrated Schottky in 3mm x 2mm DFN Features: Drives Up to Ten White LEDs from a 3V Supply High Side Sense Allows “One Wire Current Source” Internal Schottky Diode One Pin Dimming and Shutdown 80:1 True Color PWM™ Dimming Range 42V Open LED Protection 1MHz Switching Frequency ±5% Reference Accuracy VIN Range: 2.5V to 12V Requires Only 2.2µF Output Capacitor Low Profile 8-Lead DFN Package (3mm × 2mm × 0.75mm)

DC805A: Demo Board for the LTC3216 1A Low Noise High Current LED Charge Pump with Independent Torch/Flash Current Control.

DC871A-A: Demo Board for the LTC3215 700mA Low Noise High Current LED Charge Pump.

DC902A-B: Demo Board for the LTC3214 500mA Camera LED Charge Pump.

The LTC3201 is an ultralow noise, constant frequency, charge pump DC/DC converter specifically designed for powering white LEDs. The part produces a low noise boosted supply capable of supplying 100mA of output current. LED current is regulated for accurate and stable backlighting. A 3-bit DAC provides output current adjust for brightness control.Low external parts count (one small flying capacitor and three small bypass capacitors) and small MSOP-10 package size make the LTC3201 ideally suited for space constrained applications. An input noise filter further reduces input noise, thus enabling direct connection to the battery. High switching frequency enables the use of small external capacitors.The LTC3201 contains overtemperature protection and can survive an indefinite output short to GND. Internal soft-start circuitry also prevents excessive inrush current on start-up. A low current shutdown feature disconnects the load from VIN and reduces quiescent current to less than 1?A.Applications White LED Backlighting Programmable Boost Current Source

Charge Pump, 7-Channel Smart LED Driver with I2C Interface Features: Charge pump with automatic gain selection of 1×, 1.5×, and 2× for maximum efficiency 7 independent, programmable LED drivers 7 drivers capable of 30 mA (typical) 1 driver also capable of 60 mA (typical) Programmable maximum current limit (128 levels) Standby mode for <1 μA current consumption 16 programmable fade in and fade out time 0.1 sec to 5.5 sec Choose from linear, square, or cubic rates Fading override I2C-compatible interface for all programming Dedicated reset pin and built-in power-on reset (POR) Short-circuit, overvoltage, and overtemperature protection Internal soft start to limit inrush currents Input-to-output isolation during faults or shutdown Operation down to VIN = 2.5 V with undervoltage lockout (UVLO) at VIN = 2.0 V Available in a small 20-ball, 2.15 mm × 2.36 mm × 0.6 mm WLCSP or a 20-lead, 4 mm × 4 mm × 0.75 mm LFCSP

The LT8391 is a synchronous 4-switch buck-boost LED controller that regulates LED current from input voltage above, below, or equal to the output voltage. The proprietary peak-buck peak-boost current mode control scheme allows adjustable and synchronizable 150kHz to 650kHz fixed frequency operation, or internal ?15% triangle spread spectrum operation for low EMI. With 4V to 60V input, 0V to 60V output, and seamless low noise transitions between operation regions, the LT8391 is ideal for LED driver and battery charger applications in automotive, industrial, and battery-powered systems.The LT8391 provides both internal (up to 128:1) and external (up to 2000:1) LED current PWM dimming with a high-side PMOS switch. Two CTRL pins provide flexible 20:1 analog dimming with ?3% LED current accuracy at 100mV full scale. Fault protection is provided to detect an open or short LED condition, during which the LT8391 retries, latches off, or keeps running. Switching Frequency Max Output Power LT8391 Adjustable 150kHz - 650kHz 450W+ LT8391A 2MHz 50W+ APPLICATIONS Automotive Head Lamps/Running Lamps High Power LED Lighting