MAGNETORESISTIVE SENSOR IC'S ROHS COMPLIANT: YES

The ADXL373 is an ultra low power, 3-axis, ?400 g microelectromechanical systems (MEMS) accelerometer that consumes 19 ?A at a 2560 Hz output data rate (ODR). The ADXL373 does not power cycle its front end to achieve its low power operation and therefore does not run the risk of aliasing the output of the sensor.In addition to its ultra low power consumption, the ADXL373 enables impact detection while providing system level power reduction.Two additional lower power modes with interrupt driven, wake-up features are available for monitoring motion during periods of inactivity. In wake-up mode, acceleration data can be averaged to obtain a low enough output noise to trigger on low g thresholds. In instant on mode, the ADXL373 consumes 1.4 ?A while continuously monitoring the environment for impacts. When an impact event that exceeds the internally set threshold is detected, the device switches to normal operating mode fast enough to record the event.High g applications tend to experience acceleration content over a wide range of frequencies. The ADXL373 includes a four-pole, low-pass antialiasing filter to attenuate out-of-band signals that are common in high g applications. The ADXL373 also incorporates a high-pass filter to eliminate initial and slow changing errors such as ambient temperature drift.The ADXL373 provides 12-bit output data at 200 mg/LSB scale factor. The user can access configuration and data registers via the serial peripheral interface (SPI) or I2C protocol. The ADXL373 operates over a wide supply voltage range and is available in a 3.00 mm ? 3.25 mm ? 1.06 mm package.

Integrated AMR Angle Sensor and Signal Conditioner with Differential Outputs Features: Contactless angular measurement High precision 180° angle sensor Typical angular error of ±0.1° Low output noise of 850 μV rms Sine and cosine differential outputs Ratiometric analog voltage outputs Negligible hysteresis SAR or Σ-Δ ADC compatible Temperature compensated AMR bridge Industrial temperature range: −40°C to +125°C Automotive temperature range: −40°C to +150°C EMI resistant Fault diagnostics VDD from 2.7 V to 5.5 V Minimal phase error of 0.85° at 30,000 rpm AEC-Q100 qualified for automotive applications Single chip solution Available in an 8-lead SOIC package

Integrated AMR Angle Sensor and Signal Conditioner Features: High precision 180° angle sensor Maximum angular error of 0.5° Analog sine and cosine outputs Ratiometric output voltages Low thermal and lifetime drift SAR or Σ- analog-to-digital converter (ADC) drive capable Magnetoresistive (MR) bridge temperature compensation mode Temperature range: −40°C to +150°C EMI resistant Fault diagnostics VDD from 2.7 V to 5.5 V Minimum phase delay Qualified for automotive applications Available in an 8-lead SOIC package

Low Noise, High Frequency +/-50g MEMS Accelerometer Features: Single in plane axis accelerometer with analog output Linear frequency response range from dc to 11 kHz (3 dB point) Resonant frequency of 21 kHz Ultralow noise density 25 μg/√Hz in ±50 g range Overrange sensing plus dc coupling allows fast recovery time Complete electromechanical self-test Sensitivity performance Sensitivity stability over temperature 5% Linearity to ±0.1% of full-scale range Cross axis sensitivity ±1% (ZX), ±1% (YX), Single-supply operation Output voltage ratiometric to supply Low power consumption 1.0 mA Power saving standby operation mode with fast recovery RoHS compliant −40°C to +125°C temperature range 5 mm × 5 mm × 1.80 mm LFCSP package

The ADXL343 is a versatile 3-axis, digital-output, low?g MEMS accelerometer. Selectable measurement range and bandwidth, and configurable, built-in motion detection make it suitable for sensing acceleration in a wide variety of applications. Robustness to 10,000 g?of shock and a wide temperature range (?40?C to +85?C) enable use of the accelerometer even in harsh environments.The ADXL343 measures acceleration with high resolution (13-bit) measurement at up to ?16g. Digital output data is formatted as 16-bit twos complement and is accessible through either an SPI (3- or 4-wire) or I2C digital interface. The ADXL343 can measure the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (3.9 mg/LSB) enables measurement of inclination changes less than 1.0?.Several special sensing functions are provided. Activity and inactivity sensing detect the presence or lack of motion. Tap sensing detects single and double taps in any direction. Free-fall sensing detects if the device is falling. These functions can be mapped individually to either of two interrupt output pins.An integrated memory management system with a 32-level first in, first out (FIFO) buffer can be used to store data to minimize host processor activity and lower overall system power consumption.The ADXL343 is supplied in a small, thin, 3 mm ? 5 mm ? 1 mm, 14-terminal, plastic package.APPLICATIONS Handsets Gaming and pointing devices Hard disk drive (HDD) protection

The ADXL343 is a versatile 3-axis, digital-output, low?g MEMS accelerometer. Selectable measurement range and bandwidth, and configurable, built-in motion detection make it suitable for sensing acceleration in a wide variety of applications. Robustness to 10,000 g?of shock and a wide temperature range (?40?C to +85?C) enable use of the accelerometer even in harsh environments.The ADXL343 measures acceleration with high resolution (13-bit) measurement at up to ?16g. Digital output data is formatted as 16-bit twos complement and is accessible through either an SPI (3- or 4-wire) or I2C digital interface. The ADXL343 can measure the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (3.9 mg/LSB) enables measurement of inclination changes less than 1.0?.Several special sensing functions are provided. Activity and inactivity sensing detect the presence or lack of motion. Tap sensing detects single and double taps in any direction. Free-fall sensing detects if the device is falling. These functions can be mapped individually to either of two interrupt output pins.An integrated memory management system with a 32-level first in, first out (FIFO) buffer can be used to store data to minimize host processor activity and lower overall system power consumption.The ADXL343 is supplied in a small, thin, 3 mm ? 5 mm ? 1 mm, 14-terminal, plastic package.APPLICATIONS Handsets Gaming and pointing devices Hard disk drive (HDD) protection

The ADXL343 is a versatile 3-axis, digital-output, low?g MEMS accelerometer. Selectable measurement range and bandwidth, and configurable, built-in motion detection make it suitable for sensing acceleration in a wide variety of applications. Robustness to 10,000 g?of shock and a wide temperature range (?40?C to +85?C) enable use of the accelerometer even in harsh environments.The ADXL343 measures acceleration with high resolution (13-bit) measurement at up to ?16g. Digital output data is formatted as 16-bit twos complement and is accessible through either an SPI (3- or 4-wire) or I2C digital interface. The ADXL343 can measure the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (3.9 mg/LSB) enables measurement of inclination changes less than 1.0?.Several special sensing functions are provided. Activity and inactivity sensing detect the presence or lack of motion. Tap sensing detects single and double taps in any direction. Free-fall sensing detects if the device is falling. These functions can be mapped individually to either of two interrupt output pins.An integrated memory management system with a 32-level first in, first out (FIFO) buffer can be used to store data to minimize host processor activity and lower overall system power consumption.The ADXL343 is supplied in a small, thin, 3 mm ? 5 mm ? 1 mm, 14-terminal, plastic package.APPLICATIONS Handsets Gaming and pointing devices Hard disk drive (HDD) protection

The ADXL344 is a versatile 3-axis, digital-output, low?g MEMS accelerometer. Selectable measurement range and bandwidth and configurable, built-in motion detection make it suitable for sensing acceleration in a wide variety of applications. Robustness to 10,000 g?of shock and a wide temperature range (?40?C to +85?C) enable use of the accelerometer even in harsh environments.The ADXL344 measures acceleration with high resolution (13-bit) measurement at up to ?16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface. The ADXL344 can measure the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (3.9 mg/LSB) enables measurement of inclination changes less than 1.0?.Several special sensing functions are provided. Activity and inactivity sensing detect the presence or lack of motion. Tap sensing detects single and double taps in any direction. Free-fall sensing detects if the device is falling. Orientation detection reports four- and six-position orientation and can trigger an interrupt upon change in orientation. These functions can be mapped individually to either of two interrupt output pins.An integrated memory management system with a 32-level first in, first out (FIFO) buffer can be used to store data to minimize host processor activity and lower overall system power consumption.The ADXL344 is supplied in a small, thin, 3 mm ? 3 mm ? 0.95 mm, 16-terminal, plastic package.APPLICATIONS Handsets Gaming and pointing devices Personal navigation devices Hard disk drive (HDD) protection

The ADXL345 Development Board is an easy-to-use tool designed to shorten application development time by providing a ready-to-use platform for data collection and firmware development. The board is pre-configured as a datalogger that can be used to gather data for refining algorithms, tuning thresholds, and generally familiarizing oneself with accelerometer data. Powered by two AAA batteries, the board is completely untethered and integrates seamlessly into portable applications. Logged data is stored on a MicroSD memory card, providing essentially unlimited memory capacity and operating system versatility. Data is stored in a text (.txt) file, so no software installation is required to operate the board or read data. A 2GB MicroSD card and a USB MicroSD card reader are provided with the board. Additionally, the board is fully programmable, providing a hardware platform on which firmware can be tested in parallel with development of application hardware. Communications and processing are performed by an ARM7-based ADuC7024 micro-controller, and firmware is written in C. A programming cable is provided with the board, and a development environment and header files are supplied on this page. Finally, the platform can be duplicated in the final application, having already been tested with the application firmware. Schematics and layout can be found under the Supporting Documentation tab and can be used freely in your application. Note that this board is not configured to display real-time data. For real-time evaluation of the ADXL345, please refer to the Inertial Sensor Evaluation Board. For a simple ADXL345 Breakout Board, refer to the EVAL-ADXL345Z.