High Voltage 3A, 500kHz Step-Down Switching Regulator with 100A Quiescent Current Features: Wide Input Range: 3.3V to 60V 3A Peak Switch Current Burst Mode® Operation: 100µA Quiescent Current Low Shutdown Current: IQ < 1µA Power Good Flag with Programmable Threshold Load Dump Protection to 60V 500kHz Switching Frequency Saturating Switch Design: 0.1Ω On-Resistance Peak Switch Current Maintained Over Full Duty Cycle Range 1.25V Feedback Reference Voltage Easily Synchronizable Soft-Start Capability Small 16-Pin Thermally Enhanced TSSOP Package

3A, 4MHz, Monolithic Synchronous Step-Down Regulator Features: High Efficiency: Up to 95% 3A Output Current Low Quiescent Current: 64μA Low RDS(ON) Internal Switch: 77mΩ 2.25V to 5.5V Input Voltage Range Programmable Frequency: 300kHz to 4MHz ±2% Output Voltage Accuracy 0.8V Reference Allows Low Output Voltage Selectable Forced Continuous/Burst Mode® Operation with Adjustable Burst Clamp Synchronizable Switching Frequency Low Dropout Operation: 100% Duty Cycle Power Good Output Voltage Monitor Overtemperature Protected Available in 16-Lead Exposed Pad TSSOP and QFN Packages

Dual 550kHz Synchronous 2-Phase DC/DC Controller with Programmable Up/Down Tracking Features: Wide VIN Range: 3V to 30V Operation with Line Feedforward Compensation Leading Edge Modulation Architecture for Extremely Low Duty Cycle Operation Phase-Lockable Fixed Frequency: 330kHz to 750kHz Two 180° Out-of-Phase Controllers Fast Programmable Power-Up/-Down Tracking Programmable Current Limit Without External Current Sense Resistor Optional Burst Mode® Operation at Light Load ±1% 0.6V Voltage Reference External N-Channel MOSFET Architecture Low Shutdown Current: <100µA Overvoltage Protection and PGOOD Flag Small 28-Lead SSOP and 32-Lead QFN Packages

Quad Voltage Monitor and Sequencer Features: Powered from 2.7 V to 5.5 V on the VCC pin Logical core with internal timeouts provides power supply sequencing and fault protection 4 inputs can be programmed to monitor different voltage levels with resistor dividers Monitors 4 supplies via 0.8% accurate comparators 3 open-drain enable outputs Open-drain power-good output (PWRGD) 10-lead MSOP

3 kV RMS Signal and Power Isolated RS-485 Transceiver with 15 kV IEC ESD Features: 3 kV rms isolated RS-485/RS-422 transceiver Low radiated emissions, integrated, isolated dc-to-dc converter Passes EN 55032 Class B with margin on a 2-layer PCB Cable invert smart feature Correct reversed cable connection on A, B, Y, and Z bus pins while maintaining full receiver fail-safe feature ESD protection on RS-485 A, B, Y and Z pins ≥±12 kV IEC61000-4-2 contact discharge ≥±15 kV IEC61000-4-2 air discharge High speed 25 Mbps data rate (ADM2565E/ADM2567E) Low speed 500 kbps data rate for EMI control (ADM2561E/ADM2563E) Flexible power supplies Input VCC supply of 3 V to 5.5 V Logic VIO supply of 1.7 V to 5.5 V VSEL pin to select VISO supply of 5 V (VCC > 4.5 V) or 3.3 V PROFIBUS compliant for 5 V VISO Wide operating temperature range: −40°C to +105°C High common-mode transient immunity: 250 kV/µs Short-circuit, open-circuit, and floating input receiver fail-safe Supports 196 bus nodes (72 kΩ receiver input impedance) Full hot swap support (glitch free power-up/power-down) Safety and regulatory approvals (pending) CSA Component Acceptance Notice 5A, DIN V VDE V 0884-11, UL 1577, CQC11-471543-2012, IEC 61010-1 Complies with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E) 28-lead, fine pitch SOIC_W package (10.15 mm 10.05 mm) with >8.0 mm creepage and clearance

Isolated Switch Regulator with Integrated Feedback Features:Isolated PWM feedback with built in compensationPrimary side transformer driver for up to 2.5 W output power with 5 V input voltageRegulated adjustable output: 3.3 V to 24 VUp to 80% efficiency200 kHz to 1 MHz adjustable oscillatorSoft start function at power-upPulse-by-pulse overcurrent protectionThermal shutdown5000 V rms isolation High common-mode transient immunity: >25 kV/s16-lead SOIC package with 8.3 mm creepageHigh temperature operation: 105C

Single-/Dual-Supply, High Voltage Isolated IGBT Gate Driver Features: 4 A peak drive output capability Output power device resistance < 1Ω Desaturation protection Isolated Fault output Soft Shutdown on Fault Isolated Fault and Ready functions Low propagation delay 55 ns typical Minimum pulse width: 50 ns Operating temperature range: −40°C to +125°C Output voltage range to 35 V See data sheet for additional features

Micropower, 600kHz PWM DC/DC Converters Features: 100µA Quiescent Current Operates with VIN as Low as 1.5V 600kHz Fixed Frequency Operation Starts into Full Load Low-Battery Detector Active in Shutdown Automatic Burst Mode Operation at Light Load (LT1317) Continuous Switching at Light Loads (LT1317B) Low VCESAT Switch: 300mV at 500mA Pin for Pin Compatible with the LT1307/LT1307B

100VIN Forward Converter Controller Features:Input Voltage Range: 6V to 100VDuty Mode Control Regulates an Isolated Output without an OptoHigh Efficiency Synchronous ControlShort-Circuit (Hiccup Mode) Overcurrent ProtectionProgrammable OVLO and UVLO with HysteresisProgrammable Frequency (100kHz to 500kHz)Synchronizable to an External ClockPositive or Negative Polarity Output Voltage Feedback with a Single FBX PinProgrammable Soft-StartLow Shutdown Current < 1μAAvailable in FE20 TSSOP with HV Pin Spacing

Dual, Multiphase Current Mode Synchronous Controller for Sub-Milliohm DCR Sensing Features:Sub-Milliohm DCR Current SensingOperates with Power Blocks, DRMOS or External Gate Drivers and MOSFETsSupports Phase Shedding and N+1 Phase RedundancyProgrammable DCR Temperature Compensation±0.75% Maximum Total DC Output Error Over TemperatureDual Differential Remote Output Voltage Sense AmplifiersPhase-Lockable Fixed Frequency Range: 200kHz to 1.2MHzVIN Range: 4.5V to 38VVOUT Range: 0.6V to 3.5VSupports Smooth Start-Up into Pre-Biased OutputsProgrammable Soft-Start or VOUT TrackingHiccup Mode/Soft Recovery from Output Overcurrent36-Lead (5mm × 6mm) QFN Package