The LT3574 is a monolithic switching regulator specifically designed for the isolated flyback topology. No third winding or opto-isolator is required for regulation. The part senses the isolated output voltage directly from the primary side flyback waveform. A 0.65A, 60V NPN power switch is integrated along with all control logic into a 16?lead MSOP package. The LT3574 operates with input supply voltages from 3V to 40V, and can deliver output power up to 3W with no external power switch. The LT3574 utilizes boundary mode operation to provide a small magnetic solution with improved load regulation. The output voltage is easily set with two external resistors and the transformer turns ratio. Off-the-shelf transformers are available for many applications.Applications Industrial, Automotive and Medical Isolated Power Supplies

Demonstration circuit 2910A is low VIN, high efficiency, and dual 2A output µModule DC/DC converter. The board operates by default at a fixed 2MHz and can be synchronized from 1MHz to 3MHz via the MODE/SYNC pin. With its high switching frequency and current mode architecture, a fast transient response to line and load changes is possible without sacrificing stability. The DC2910A can be used in forced continuous mode or pulse skip mode for low noise, or in burst mode operation for high efficiency at light loads. The demo board features the LTM4691, which is available in a low profile 3mm x 4mm x 1.2mm LGA package. Please see the LTM4691 datasheet for more detailed information. It is recommended to read the data sheet for the LTM4691 prior to making any changes to the DC2910A.

Ultra-Low-Noise, High-Accuracy 2.5V Voltage Reference Features: Maximum temperature coefficient (TCVOUT): 0.8 ppm/°C (D grade 0°C to 70°C) 1 ppm/°C (C grade 0°C to 70°C) 2 ppm/°C (B grade −40°C to +125°C) 4 ppm/°C (A grade 40°C to +125°C) Output noise (0.1 Hz to 10 Hz): 1 μV p-p at VOUT of 2.048 V typical Initial output voltage error: B, C, D grade: ±0.02% (maximum) Input voltage range: 3 V to 15 V Operating temperature: A grade and B grade: −40°C to +125°C C grade: 0°C to +70°C Output current: +10 mA source/−10 mA sink Low quiescent current: 950 μA (maximum) Low dropout voltage: 300 mV at 2 mA (VOUT ≥ 3 V) 8-lead SOIC package and LCC package AEC-Q100 qualified for automotive applications Long-term drift: 8 ppm typical at 4500 hours

High Efficiency Bidirectional Multicell Battery Balancer Features: Bidirectional Synchronous Flyback Balancing of Up to 6 Li-Ion or LiFePO4 Cells in Series Up to 10A Balancing Current (Set by Externals) Integrates Seamlessly with the LTC680x Family of Multicell Battery Stack Monitors Bidirectional Architecture Minimizes Balancing Time and Power Dissipation Up to 92% Charge Transfer Efficiency Stackable Architecture Enables >1000V Systems Uses Simple 2-Winding Transformers 1MHz Daisy-Chainable Serial Interface with 4-Bit CRC Packet Error Checking High Noise Margin Serial Communication Numerous Fault Protection Features 48-Lead Exposed Pad QFN and LQFP Packages AEC-Q100 Qualified for Automotive Applications

The ADM6711/ADM6713 are reset generator circuits suitable for use in microprocessor-based systems. They provide a reset signal on power-up, power-down, and whenever the supply voltage falls below a preset threshold. In addition, both parts have a debounced manual reset input so that a reset signal can also be initiated with an external switch or logic signal.With six different reset threshold options available ranging from 2.32 V to 4.63 V, the ADM6711/ADM6713 are suitable for monitoring 2.5 V, 3 V, 3.3 V, and 5 V supplies. A reset timeout of at least 140 ms occurs when VCC rises above the threshold. This gives the supply voltage time to stabilize before the microprocessor starts up.The ADM6711 has a push-pull output, so no additional external components are needed. The ADM6713 open-drain output requires an external pull-up resistor that can be connected to a voltage higher than VCC, if desired.The parts are highly reliable with accurate voltage references and immunity to fast, negative-going transients on VCC. Low current consumption and space-efficient, 4-lead SC70 packaging make the ADM6711/ADM6713 ideal for use in low power portable applications.APPLICATIONS Microprocessor systems Computers Controllers Intelligent instruments Automotive systems

Microprocessor Supervisor with Backup Battery Switchover, Adjustable Reset and Watchdog Periods, Chip Enable Signals, 4.65V Threshold Voltage, Watchdog, Battery Backup and Low VCC Status O/Ps and 250mA Output Current Features: Low Power Consumption: Precision Voltage Monitor ±2% Tolerance on ADM800L/M Reset Time Delay—200 ms, or Adjustable 1 µA Standby Current Automatic Battery Backup Power Switching Fast Onboard Gating of Chip Enable Signals Also Available in TSSOP Package (ADM691A)

MICROPROCESSOR SUPERVISORS / VOLTAGE DET;

Power Management IC Development Tools LTC2952 Demo Board Push-Button Power Path Controller w/ Supervisor

VOLT REF, NSOIC-8, -40 TO 125DEG C;

The LTC3110 is a 2A bidirectional buck-boost DC/DC regulator with capacitor charger and balancer. Its wide 0.1V to 5.5V capacitor/battery voltage and 1.8V to 5.25V system backup voltage ranges make it well suited to a wide variety of backup applications using supercapacitors or batteries. A proprietary low noise switching algorithm optimizes efficiency with capacitor/battery voltages that are above, below or equal to the system output voltage.The LTC3110 can autonomously transition from charge to backup mode or switch modes based on an external command. Pin-selectable Burst Mode operation reduces standby current and improves light-load efficiency, which combined with a 1μA shutdown current make the LTC3110 ideally suited for backup applications. Additional features include voltage supervisors for direction control and end of charge, and a general purpose comparator with open-collector output for interfacing with a μC. The LTC3110 is available in thermally enhanced, low profile 24-lead TSSOP and 4mm × 4mm QFN packages.Applications Supercapacitor Backup Converter and Charger Battery Backup Converter and Charger Servers, RAID Systems RF Systems with Battery/Capacitor Backup