High Voltage Input Protection Device Features: Controls supply voltages from 4 V to 60 V Gate drive for low voltage drop reverse supply protection Gate drive for P-channel FETs Inrush current limiting control Adjustable current limit Foldback current limiting Automatic retry or latch-off on current fault Programmable current-limit timer for safe operating area (SOA) Power-good and fault outputs Analog undervoltage (UV) and overvoltage (OV) protection 16-lead, 3 mm × 3 mm LFCSP 16-lead QSOP

High Voltage Input Protection Device Features: Controls supply voltages from 4 V to 60 V Gate drive for low voltage drop reverse supply protection Gate drive for P-channel FETs Inrush current limiting control Adjustable current limit Foldback current limiting Automatic retry or latch-off on current fault Programmable current-limit timer for safe operating area (SOA) Power-good and fault outputs Analog undervoltage (UV) and overvoltage (OV) protection 16-lead, 3 mm × 3 mm LFCSP 16-lead QSOP

High Voltage Input Protection Device Features: Controls supply voltages from 4 V to 60 V Gate drive for low voltage drop reverse supply protection Gate drive for P-channel FETs Inrush current limiting control Adjustable current limit Foldback current limiting Automatic retry or latch-off on current fault Programmable current-limit timer for safe operating area (SOA) Power-good and fault outputs Analog undervoltage (UV) and overvoltage (OV) protection 16-lead, 3 mm × 3 mm LFCSP 16-lead QSOP

10 Volt Precision Reference Series Features:Very High Accuracy: 10,000 Volts 2.5mV (L and U)Low Temperature Coefficient: 3ppm/CPerformance Guaranteed -55C to +125C10mA Output Current CapabilityLow NoiseShort Circuit ProtectedAvailable as /883B

18-Cell Battery Monitor with Daisy Chain Interface Features: Measures up to 18 battery cells in series 3 mV maximum total measurement error Stackable architecture for high voltage systems Built-in isoSPI interface 1 Mb isolated serial communications Uses a single twisted pair, up to 100 meters Low EMI susceptibility and emissions Bidirectional for broken wire protection 290 μs to measure all cells in a system Synchronized voltage and current measurement 16-bit Δ-Σ ADC with programmable third-order noise filter Passive cell balancing up to 200 mA (maximum) with programmable pulsewidth modulation 9 general purpose digital I/O or analog inputs Temperature or other sensor inputs Configurable as an I2C or SPI master 6 μA sleep mode supply current 64-lead LQFP_EP package

Quad Voltage Monitor and Sequencer Features: Powered from 2.7 V to 5.5 V on the VCC pin Logical core with internal timeouts provides power supply sequencing and fault protection 4 inputs can be programmed to monitor different voltage levels with resistor dividers Monitors 4 supplies via 0.8% accurate comparators 3 open-drain enable outputs Open-drain power-good output (PWRGD) 10-lead MSOP

3 kV RMS Signal and Power Isolated RS-485 Transceiver with 15 kV IEC ESD Features: 3 kV rms isolated RS-485/RS-422 transceiver Low radiated emissions, integrated, isolated dc-to-dc converter Passes EN 55032 Class B with margin on a 2-layer PCB Cable invert smart feature Correct reversed cable connection on A, B, Y, and Z bus pins while maintaining full receiver fail-safe feature ESD protection on RS-485 A, B, Y and Z pins ≥±12 kV IEC61000-4-2 contact discharge ≥±15 kV IEC61000-4-2 air discharge High speed 25 Mbps data rate (ADM2565E/ADM2567E) Low speed 500 kbps data rate for EMI control (ADM2561E/ADM2563E) Flexible power supplies Input VCC supply of 3 V to 5.5 V Logic VIO supply of 1.7 V to 5.5 V VSEL pin to select VISO supply of 5 V (VCC > 4.5 V) or 3.3 V PROFIBUS compliant for 5 V VISO Wide operating temperature range: −40°C to +105°C High common-mode transient immunity: 250 kV/µs Short-circuit, open-circuit, and floating input receiver fail-safe Supports 196 bus nodes (72 kΩ receiver input impedance) Full hot swap support (glitch free power-up/power-down) Safety and regulatory approvals (pending) CSA Component Acceptance Notice 5A, DIN V VDE V 0884-11, UL 1577, CQC11-471543-2012, IEC 61010-1 Complies with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E) 28-lead, fine pitch SOIC_W package (10.15 mm 10.05 mm) with >8.0 mm creepage and clearance

Isolated Switch Regulator with Integrated Feedback Features:Isolated PWM feedback with built in compensationPrimary side transformer driver for up to 2.5 W output power with 5 V input voltageRegulated adjustable output: 3.3 V to 24 VUp to 80% efficiency200 kHz to 1 MHz adjustable oscillatorSoft start function at power-upPulse-by-pulse overcurrent protectionThermal shutdown5000 V rms isolation High common-mode transient immunity: >25 kV/s16-lead SOIC package with 8.3 mm creepageHigh temperature operation: 105C

Precision Reference Features: Ultralow Drift: 5ppm/C Max SlopeVery Low Noise: P-P (0.1Hz to 10Hz)100% Noise TestedPin Compatible with Most Bandgap Reference Applications, Including REF01, REF02, LM368, MC1400 and MC1404 with Greatly Improved Stability, Noise and DriftTrimmed Output VoltageOperates in Series or Shunt ModeOutput Sinks and Sources in Series Mode>100dB Ripple RejectionMinimum Input/Output Differential of 1VAvailable in 5-Lead Can, N8 and S8 Packages

Precision 10V Reference Features: Pin Compatible with LH0070 and AD581 Ultralow Drift—5ppm/°C Max Slope Trimmed Output Voltage Operates in Series or Shunt Mode Output Sinks and Sources in Series Mode Very Low Noise < 1ppmP-P 0.1Hz to 10Hz > 100dB Ripple Rejection Minimum Input Voltage of 11V