100VIN Forward Converter Controller Features:Input Voltage Range: 6V to 100VDuty Mode Control Regulates an Isolated Output without an OptoHigh Efficiency Synchronous ControlShort-Circuit (Hiccup Mode) Overcurrent ProtectionProgrammable OVLO and UVLO with HysteresisProgrammable Frequency (100kHz to 500kHz)Synchronizable to an External ClockPositive or Negative Polarity Output Voltage Feedback with a Single FBX PinProgrammable Soft-StartLow Shutdown Current < 1μAAvailable in FE20 TSSOP with HV Pin Spacing

High Efficiency, Secondary-Side Synchronous Forward Controller Features: Direct Flux Limit™ Guarantees No Saturation Fast and Accurate Average Current Limit Clean Start-Up Into Pre-Biased Output Secondary-Side Control for Fast Transient Response Simple, Self-Starting Architecture Synchronous MOSFET Reverse Current Limit PolyPhase® Operation Eases High-Power Design True Remote Sense Differential Amplifier Remote Sense Reverse Protection High Voltage Linear Regulator Controller Internal LDO Powers Gate Drive from VOUT Overtemperature/Overvoltage Protection Low Profile 4mm × 5mm QFN and Narrow 28-Lead SSOP Packages

Dual 18A or Single 36A Module (Power Module) Regulator with 0.8% DC and 3% Transient Accuracy Features:±0.8% Maximum Total DC Output Error Over Line, Load and Temperature (LTM4630-1A)±3% Transient Output Error with Minimum Output CapacitanceDual 18A or Single 36A Output4.5V to 15V Input, 0.6V to 1.8V Output Voltage RangeDifferential Remote Sense AmplifierCurrent Mode Control/Fast Transient ResponseCurrent Sharing Up to 144A16mm × 16mm × 5.01mm BGA Package

SAFETY SYSTEM BASIS CHIP WITH LOW POWER FOR ASIL D, LQFP-48 TRAY / TRAY ROHS COMPLIANT: YES

SAFETY SYSTEM BASIS CHIP WITH LOW POWER FOR ASIL D, LQFP-48 TRAY / TRAY ROHS COMPLIANT: YES

Synchronous Current-Mode Buck Controller with Constant On-time, 0.8 V Reference Voltage, and Power Saving Mode Features: Power input voltage as low as 2.75 V to 20 V Bias supply voltage range: 2.75 V to 5.5 V Minimum output voltage: 0.6 V 0.8 V reference voltage with ±1.0% accuracy Supports all N-channel MOSFET power stages Available in 300 kHz, 600 KHz, and 1.0 MHz options No current-sense resistor required Power saving mode (PSM) for light loads (ADP1883 only) Resistor Programmable Current Sense Gain Thermal overload protection Short-circuit protection See data sheet for additional features

20 V, 6 A, Synchronous Step-Down DC-to-DC Regulator Features: Input voltage: 4.5 V to 20 V Integrated MOSFET: 44 m/11 m Reference voltage: 0.6 V ± 1% Continuous output current: 6 A Programmable switching frequency: 200 kHz to 1.4 MHz Synchronizes to external clock: 200 kHz to 1.4 MHz 180° out of phase clock synchronization Precision enable and power good External compensation Internal soft start with external adjustable option Startup into a precharged output Supported by ADIsimPower design tool

3 A, 36 V, Synchronous Step-Down DC-to-DC Regulator Features: Continuous output current: 3 A Input voltage: 4.5 V to 36 V Integrated MOSFETs: 98 mΩ/35 mΩ Reference voltage: 0.6 V ± 1% Fast minimum on time: 50 ns Programmable switching frequency: 200 kHz to 1.8 MHz Synchronizes to external clock: 200 kHz to 1.8 MHz Precision enable and power good Cycle-by-cycle current limit with hiccup protection External compensation Programmable soft start time Startup into a precharged output Supported by ADIsimPower design tool

Integrated Power Solution with Quad Buck Regulators, Supervisory, and I2C Interface Features: Wide input voltage range: 4.5 V to 15.0 V ±1.5% output accuracy over full temperature range Adjustable/fixed output options via factory fuse or I2C interface I2C interface with interrupt on fault conditions Power regulation Channel 1 and Channel 2: programmable 1.2 A/2.5 A/4 A sync buck regulators with low-side FET driver Channel 3 and Channel 4: 1.2 A sync buck regulators 250 kHz to 1.4 MHz adjustable switching frequency Single 8 A output (Channel 1 and Channel 2 in parallel) Dynamic voltage scaling (DVS) for Channel 1 and Channel 4 Precision enable with 0.8 V accurate threshold Programmable phase shift in 90° steps Individual channel FPWM/PSM selection Frequency synchronization input or output See data sheet for additional features

800 mA, DC-to-DC Inverting Regulator Features: Wide input voltage range: 2.85 V to 15 V Adjustable negative output to VIN − 39 V Integrated 800 mA main switch 1.2 MHz/2.4 MHz switching frequency with optional external frequency synchronization from 1.0 MHz to 2.6 MHz Resistor programmable soft start timer Slew rate control for lower system noise Precision enable control UVLO, OCP, OVP, and TSD protection 1.61 mm × 2.18 mm, 12-ball WLCSP −40°C to +125°C junction temperature Supported by the ADIsimPower tool set