8 Channel, PDM to I2S/TDM Converter Features: 8 channels of PDM audio inputs from digital microphones 16×, 32×, or 64× decimation ratio of PDM to PCM audio data 24-bit resolution to support high sound pressure level (SPL) microphones 126 dB A-weighted SNR 4 kHz to 192 kHz output sampling rate Bit clock rates of 64×, 128×, 192×, 256×, 384×, or 512× the output sampling rate Dual output PDM clocks Automatic PDM clock generation Automatic power-down when BCLK removed Selectable I2C control or hardware mode operation 1.2 mA DVDD operating current for 8 channels at 48 kHz frequency sampling rate and 1.8 V supply Slave I2S or TDM output interface Up to TDM-16 supported Configurable TDM slot routing and sizes I/O supply voltage from 1.70 V to 3.63 V DVDD supply voltage from 1.10 V to 1.98 V <5 μA typical DVDD shutdown current 16-lead, 3 mm × 3 mm, 0.50 mm pitch LFCSP Power-on reset

18-Cell Battery Monitor with Daisy Chain Interface Features: Measures up to 18 battery cells in series 3 mV maximum total measurement error Stackable architecture for high voltage systems Built-in isoSPI interface 1 Mb isolated serial communications Uses a single twisted pair, up to 100 meters Low EMI susceptibility and emissions Bidirectional for broken wire protection 290 μs to measure all cells in a system Synchronized voltage and current measurement 16-bit Δ-Σ ADC with programmable third-order noise filter Passive cell balancing up to 200 mA (maximum) with programmable pulsewidth modulation 9 general purpose digital I/O or analog inputs Temperature or other sensor inputs Configurable as an I2C or SPI master 6 μA sleep mode supply current 64-lead LQFP_EP package

Dual Channel, Configurable, IsolatedDigital Input Features: Dual channel, configurable, isolated digital input Programmable trip threshold On-chip debounce filter On-chip data and power Isolation Application circuit monitors wide voltage range 10 V dc to 300 V dc 8 V rms to 240 V rms ac (with 10 ms + pickup) Negative dc protected Programmable wetting current Pulse up to 50 mA Constant current up to 6.3 mA Safety and regulatory approvals UL recognition 3750 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice #5A (pending) CSA 61010-1: 300 V rms VDE certificate of conformity (pending) DIN V VDE V 0884-11 (VDE V 0884-11):2017-1 VIORM = 565 V peak EMC robust solution supports relay protection system level requirements ADC samples available for system diagnostics Internal SAR ADC with PGA Single 3.3 V Supply Integrated isoPower, isolated dc-to-dc converter Interfaces SPI DOUTx output reflects state of digital input IRQ interrupt pin Operating temperature: −40°C to +125°C 20-lead, LGA package with 6.8 mm creepage

High Performance Polyphase Energy Measurement IC Features: 7 high performance analog-to-digital converters (ADCs) 101 dB signal-to-noise ratio (SNR) 10,000:1 dynamic range Wide input range: ±1 V, 0.707 V rms full scale Differential inputs ±25 ppm/°C maximum channel temperature drift (including ADC, internal VREF, and PGA drift) enabling Class 0.2 meters with standard external components Power quality measurements Line frequency: 1 measurement per phase Zero crossing detection, zero-crossing timeout Phase angle measurements Supports current transformers (CTs) and Rogowski coil (di/dt) sensors Multiple range phase/gain compensation for CTs Digital integrator for Rogowski coils Flexible waveform buffer Able to resample waveform to ensure 64 points per line cycle for ease of external harmonic analysis Events can trigger waveform storage Simplifies data collection for IEC 61000-4-7 harmonic analysis Advanced metrology feature set Total active power, volt-amperes reactive (VAR), volt-amperes (VA), watthour, VAR-hour, and VA-hour Fundamental VAR and VAR-hour Current and voltage rms per phase (xIRMS, xVRMS) Supports active energy standards: IEC 62053-21, IEC 62053-22; EN50470-3; OIML R46, ANSI C12.20 Supports reactive energy standards: IEC 62053-23, IEC 62053-4 High speed communication port 10 MHz serial peripheral interface (SPI)

0.4 CMOS, Dual DPDT Switch in WLCSP/LFCSP/TSSOP Features: 1.8 V to 5.5 V operation Ultralow on resistance 0.4 Ω typical 0.6 Ω maximum at 5 V supply Excellent audio performance, ultralow distortion 0.07 Ω typical 0.14 Ω maximum RON flatness High current carrying capability 400 mA continuous 600 mA peak current at 5 V Automotive temperature range: −40°C to +125°C Rail-to-rail switching operation Typical power consumption (<0.1 μW)

0 Hz/dc to 14 GHz, Single-Pole, Four-Throw MEMS Switch with Integrated Driver Features: Fully operational down to 0 Hz/dc On resistance: 2.9 Ω (maximum) Off leakage: 0.5 nA (maximum) −3 dB bandwidth 11 GHz (typical) for RF1, RF4 14 GHz (typical) for RF2, RF3 RF performance characteristics Insertion loss: 0.26 dB (typical) at 2.5 GHz Isolation: 24 dB (typical) at 2.5 GHz IIP3: 69 dBm (typical) RF power: 36 dBm (maximum) Actuation lifetime: 1 billion cycles (minimum) Hermetically sealed switch contacts On switching time: 75 μs (maximum) Integrated driver removes the need for an external driver Supply voltage: 3.0 V to 3.6 V CMOS-/LVTTL-compatible Parallel and SPI interface Independently controllable switches Switch is in an open state with no power supply present Requirement to avoid floating nodes on all RFx pins (see the Floating Node section in data sheet) 24-lead, 5 mm × 4 mm × 0.95 mm, LFCSP Operating temperature range: 0°C to 85°C

Quad Voltage Monitor and Sequencer Features: Powered from 2.7 V to 5.5 V on the VCC pin Logical core with internal timeouts provides power supply sequencing and fault protection 4 inputs can be programmed to monitor different voltage levels with resistor dividers Monitors 4 supplies via 0.8% accurate comparators 3 open-drain enable outputs Open-drain power-good output (PWRGD) 10-lead MSOP

3 kV RMS Signal and Power Isolated RS-485 Transceiver with 15 kV IEC ESD Features: 3 kV rms isolated RS-485/RS-422 transceiver Low radiated emissions, integrated, isolated dc-to-dc converter Passes EN 55032 Class B with margin on a 2-layer PCB Cable invert smart feature Correct reversed cable connection on A, B, Y, and Z bus pins while maintaining full receiver fail-safe feature ESD protection on RS-485 A, B, Y and Z pins ≥±12 kV IEC61000-4-2 contact discharge ≥±15 kV IEC61000-4-2 air discharge High speed 25 Mbps data rate (ADM2565E/ADM2567E) Low speed 500 kbps data rate for EMI control (ADM2561E/ADM2563E) Flexible power supplies Input VCC supply of 3 V to 5.5 V Logic VIO supply of 1.7 V to 5.5 V VSEL pin to select VISO supply of 5 V (VCC > 4.5 V) or 3.3 V PROFIBUS compliant for 5 V VISO Wide operating temperature range: −40°C to +105°C High common-mode transient immunity: 250 kV/µs Short-circuit, open-circuit, and floating input receiver fail-safe Supports 196 bus nodes (72 kΩ receiver input impedance) Full hot swap support (glitch free power-up/power-down) Safety and regulatory approvals (pending) CSA Component Acceptance Notice 5A, DIN V VDE V 0884-11, UL 1577, CQC11-471543-2012, IEC 61010-1 Complies with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E) 28-lead, fine pitch SOIC_W package (10.15 mm 10.05 mm) with >8.0 mm creepage and clearance

3 kV RMS Signal and Power Isolated RS-485 Transceiver with 15 kV IEC ESD Features: 3 kV rms isolated RS-485/RS-422 transceiver Low radiated emissions, integrated, isolated dc-to-dc converter Passes EN 55032 Class B with margin on a 2-layer PCB Cable invert smart feature Correct reversed cable connection on A, B, Y, and Z bus pins while maintaining full receiver fail-safe feature ESD protection on RS-485 A, B, Y and Z pins ≥±12 kV IEC61000-4-2 contact discharge ≥±15 kV IEC61000-4-2 air discharge High speed 25 Mbps data rate (ADM2565E/ADM2567E) Low speed 500 kbps data rate for EMI control (ADM2561E/ADM2563E) Flexible power supplies Input VCC supply of 3 V to 5.5 V Logic VIO supply of 1.7 V to 5.5 V VSEL pin to select VISO supply of 5 V (VCC > 4.5 V) or 3.3 V PROFIBUS compliant for 5 V VISO Wide operating temperature range: −40°C to +105°C High common-mode transient immunity: 250 kV/µs Short-circuit, open-circuit, and floating input receiver fail-safe Supports 196 bus nodes (72 kΩ receiver input impedance) Full hot swap support (glitch free power-up/power-down) Safety and regulatory approvals (pending) CSA Component Acceptance Notice 5A, DIN V VDE V 0884-11, UL 1577, CQC11-471543-2012, IEC 61010-1 Complies with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E) 28-lead, fine pitch SOIC_W package (10.15 mm 10.05 mm) with >8.0 mm creepage and clearance

5.7 kV RMS Isolated, High Working Voltage, RS-485 Transceiver with 15 kV IEC ESD Features: 5.7 kV rms, signal isolated RS-485 transceiver 1500 V peak and dc working voltage to DIN V VDE 0884-11 Low radiated emissions: passes EN 55032, Class B with margin on a 2-layer PCB Receiver cable inversion smart feature Correction for reversed cable connection on A and B bus pins while maintaining full receiver fail-safe feature ESD protection on the RS-485 A, B, Y, and Z bus pins ≥ ±12 kV IEC 61000-4-2 contact discharge ≥ ±15 kV IEC 61000-4-2 air discharge Low speed 500 kbps data rate for EMI control Flexible power supply inputs Primary VDD1 supply of 1.7 V to 5.5 V Isolated VDD2 supply of 3.0 V to 5.5 V Profibus® Compliant for 5V VDD2 Wide −40°C to +125°C operating temperature range High common-mode transient immunity: >250 kV/μs Short-circuit, open-circuit, and floating input receiver fail-safe Supports 192 bus nodes (72 kΩ receiver input impedance) Full hot swap support (glitch free power-up and power-down) Safety and regulatory approvals (pending) CSA Component Acceptance Notice 5A, DIN V VDE 0884-11, UL 1577, CQC11-471543-2012, IEC 61010-1 16-lead, wide-body, SOIC_W package with 8.3 mm creepage and clearance in standard pinout