The LTC2376-16 is a low noise, low power, high speed 16-bit successive approximation register (SAR) ADC. Operating from a 2.5V supply, the LTC2376-16 has a ±VREF fully differential input range with VREF ranging from 2.5V to 5.1V. The LTC2376-16 consumes only 3.4mW and achieves ±0.5LSB INL maximum, no missing codes at 16 bits with 97dB SNR.The LTC2376-16 has a high speed SPI-compatible serial interface that supports 1.8V, 2.5V, 3.3V and 5V logic while also featuring a daisy-chain mode. The fast 250ksps throughput with no cycle latency makes the LTC2376-16 ideally suited for a wide variety of high speed applications. An internal oscillator sets the conversion time, easing external timing considerations. The LTC2376-16 automatically powers down between conversions, leading to reduced power dissipation that scales with the sampling rate.The LTC2376-16 features a unique digital gain compression (DGC) function, which eliminates the driver amplifier’s negative supply while preserving the full resolution of the ADC. When enabled, the ADC performs a digital scaling function that maps zero-scale code from 0V to 0.1 • VREF and full-scale code from VREF to 0.9 • VREF. For a typical reference voltage of 5V, the full-scale input range is now 0.5V to 4.5V, which provides adequate headroom for powering the driving amplifier from a single 5.5V supply.Applications Medical Imaging High Speed Data Acquisition Portable or Compact Instrumentation Industrial Process Control Low Power Battery-Operated Instrumentation ATE

The LT4363 surge stopper protects loads from high voltage transients. It regulates the output during an overvoltage event, such as load dump in vehicles, by controlling the gate of an external N-channel MOSFET. The output is limited to a safe value allowing the loads to continue functioning. The LT4363 also monitors the voltage drop between the SNS and OUT pins to protect against overcurrent faults. An internal amplifier limits the voltage across the current sense resistor to 50mV. In either fault condition, a timer is started inversely proportional to MOSFET stress. Before the timer expires, the FLT pin pulls low to warn of an impending power down. If the condition persists, the MOSFET is turned off. The LT4363-1 remains off until reset whereas the LT4363-2 restarts after a cool down period.Two precision comparators can monitor the input supply for overvoltage (OV) and undervoltage (UV) conditions. When the potential is below the UV threshold, the external MOSFET is kept off. If the input supply voltage is above the OV threshold, the MOSFET is not allowed to turn back on. Back-to-back MOSFETs can be used in lieu of a Schottky diode for reverse input protection, reducing voltage drop and power loss. A shutdown pin reduces the quiescent current to less than 7μA during shutdown.Applications Automotive/Avionic Surge Protection Hot Swap™/Live Insertion High Side Switch for Battery Powered Systems Intrinsic Safety Applications

The LTC3111 is a fixed frequency, synchronous buckboost DC/DC converter with an extended input and output range. The unique 4-switch, single inductor architecture provides low noise and seamless operation from input voltages above, below or equal to the output voltage.With an input and output range of 2.5V to 15V, the LTC3111 is well suited for a wide variety of single or multiple-cell batteries, back-up capacitor or wall adapter source applications. Low RDS(ON) internal N-channel MOSFET switches and selectable PWM or Burst Mode operation produce high efficiency over a wide range of operating conditions. An accurate RUN pin allows the user to program the turn-on threshold voltage of the converter. Other features include: short-circuit protection, internal soft-start and thermal shutdown.The LTC3111 is offered in both thermally enhanced 14-lead (3mm × 4mm × 0.75mm) DFN and 16-lead MSOP packages.Applications 3.3V or 5V from 1, 2 or 3 Li-Ion, Multiple-Cell Alkaline/NiMH Batteries RF Transmitters Military, Industrial Power Systems

The ADuM3400/ADuM3401/ADuM3402 are 4-channel digitalisolators based on the Analog Devices, Inc., iCoupler® technology.Combining high speed CMOS and monolithic air coretransformer technology, these isolation components provideoutstanding performance characteristics superior to alternativessuch as optocoupler devices.iCoupler devices remove the design difficulties commonlyassociated with optocouplers. Typical optocoupler concernsregarding uncertain current transfer ratios, nonlinear transferfunctions, and temperature and lifetime effects are eliminatedwith the simple iCoupler digital interfaces and stable performancecharacteristics. The need for external drivers and other discretecomponents is eliminated with these iCoupler products. Furthermore,iCoupler devices consume one-tenth to one-sixth thepower of optocouplers at comparable signal data rates.The isolators provide four independent isolation channels in avariety of channel configurations and data rates (see theOrdering Guide). All models operate with the supply voltage oneither side ranging from 2.7 V to 5.5 V, providing compatibilitywith lower voltage systems as well as enabling a voltagetranslation functionality across the isolation barrier. Theisolators have a patented refresh feature that ensures dc correctnessin the absence of input logic transitions and during powerup/power-downconditions.In comparison to the ADuM1400/ADuM1401/ADuM1402isolators, the ADuM3400/ADuM3401/ADuM3402 isolatorscontain various circuit and layout changes to provide increasedcapability relative to system-level IEC 61000-4-x testing (ESD/burst/surge). The precise capability in these tests for either set ofisolators is strongly determined by the design and layout of theuser’s board or module. For more information, see the AN-793 application note, ESD/Latch-Up Considerations with iCoupler Isolation Products.Applications General-purpose multichannel isolation SPI/data converter isolation RS-232/RS-422/RS-485 transceivers Industrial field bus isolation

The ADuM3400/ADuM3401/ADuM3402 are 4-channel digitalisolators based on the Analog Devices, Inc., iCoupler® technology.Combining high speed CMOS and monolithic air coretransformer technology, these isolation components provideoutstanding performance characteristics superior to alternativessuch as optocoupler devices.iCoupler devices remove the design difficulties commonlyassociated with optocouplers. Typical optocoupler concernsregarding uncertain current transfer ratios, nonlinear transferfunctions, and temperature and lifetime effects are eliminatedwith the simple iCoupler digital interfaces and stable performancecharacteristics. The need for external drivers and other discretecomponents is eliminated with these iCoupler products. Furthermore,iCoupler devices consume one-tenth to one-sixth thepower of optocouplers at comparable signal data rates.The isolators provide four independent isolation channels in avariety of channel configurations and data rates (see theOrdering Guide). All models operate with the supply voltage oneither side ranging from 2.7 V to 5.5 V, providing compatibilitywith lower voltage systems as well as enabling a voltagetranslation functionality across the isolation barrier. Theisolators have a patented refresh feature that ensures dc correctnessin the absence of input logic transitions and during powerup/power-downconditions.In comparison to the ADuM1400/ADuM1401/ADuM1402isolators, the ADuM3400/ADuM3401/ADuM3402 isolatorscontain various circuit and layout changes to provide increasedcapability relative to system-level IEC 61000-4-x testing (ESD/burst/surge). The precise capability in these tests for either set ofisolators is strongly determined by the design and layout of theuser’s board or module. For more information, see the AN-793 application note, ESD/Latch-Up Considerations with iCoupler Isolation Products.Applications General-purpose multichannel isolation SPI/data converter isolation RS-232/RS-422/RS-485 transceivers Industrial field bus isolation

The ADuM520x are dual channel digital isolators with isoPower, an integrated, isolated dc-to-dc converter. Based onthe Analog Devices, Inc., iCoupler® technology, the dc-to-dcconverter provides up to 500 mW of regulated, isolated powerwith 5.0 V input and 5.0 V output voltage, or 200 mW of power with 3.3 V input and 3.3 V output voltage. This eliminates the need for a separate isolated dc-to-dc converter in low power isolated designs. The Analog Devices chip scale transformer iCoupler technology is used for the isolation of the logic signals as well as for the dc-to-dc converter. The result is a small form factor, total isolation solution.ADuM520x units may be used in combination with ADuM5401, ADuM5402, ADuM5403, ADuM5404 and ADuM5000 with isoPower® to achieve higher output power levels and greater channel counts (see the Increasing Available Power section).The ADuM520x isolators provide two independent isolationchannels in a variety of channel configurations and data rates(see the Ordering Guide for options).isoPower uses high frequency switching elements to transfer power through its transformer. Special care must be taken during printed circuit board (PCB) layout to meet emissionsstandards. Refer to the AN-0971 application note for details on board layout recommendations.APPLICATIONS RS-232/RS-422/RS-485 transceiver Industrial field bus isolation Power supply startups and gate drives Isolated sensor interfaces Industrial PLCs

The ADuM524x are dual-channel digital isolators with isoPower integrated, isolated power. Based on the Analog Devices, Inc. iCoupler® technology, a chip-scale DC/DC converter provides up to 50 mW of regulated, isolated power at 5 V, which eliminates the need for a separate isolated DC/DC converter in low power isolated designs. The Analog Devices chip-scale transformer iCoupler technology is used both for the isolation of the logic signals as well as for the DC/DC converter. The result is a small form factor, total isolation solution.The ADuM524x isolators provide two independent isolation channels in a variety of channel configurations, operating from a 5 V input supply. ADuM524x units may be used in combination with other iCoupler products to achieve greater channel counts.

The ADuM524x are dual-channel digital isolators with isoPower integrated, isolated power. Based on the Analog Devices, Inc. iCoupler® technology, a chip-scale DC/DC converter provides up to 50 mW of regulated, isolated power at 5 V, which eliminates the need for a separate isolated DC/DC converter in low power isolated designs. The Analog Devices chip-scale transformer iCoupler technology is used both for the isolation of the logic signals as well as for the DC/DC converter. The result is a small form factor, total isolation solution.The ADuM524x isolators provide two independent isolation channels in a variety of channel configurations, operating from a 5 V input supply. ADuM524x units may be used in combination with other iCoupler products to achieve greater channel counts.

The ADuM5401 / ADuM5402 / ADuM5403 / ADuM5404 arequad-channel digital isolators with isoPower®, an integrated,isolated dc-to-dc converter. Based on the Analog Devices, Inc.,iCoupler® technology, the dc-to-dc converter provides up to 500 mW of regulated, isolated power at either 5.0 V or 3.3 Vfrom a 5.0 V input supply, or at 3.3 V from a 3.3 V supply at thepower levels shown in Table 1. These devices eliminate the need for a separate, isolated dc-to-dc converter in low power, isolated designs. The iCoupler chip scale transformer technology is used to isolate the logic signals and for the power and feedback pathsin the dc-to-dc converter. The result is a small form factor, total isolation solution.The ADuM5401 / ADuM5402 / ADuM5403 / ADuM5404 isolatorsprovide four independent isolation channels in a variety of channel configurations and data rates (see the Ordering Guidefor more information).isoPower uses high frequency switching elements to transfer power through its transformer. Special care must be taken during printed circuit board (PCB) layout to meet emissionsstandards. See the AN-0971 Application Note for board layout recommendations.APPLICATIONS RS-232/RS-422/RS-485 transceivers Industrial field bus isolation Power supply startup bias and gate drives Isolated sensor interfaces Industrial PLCs

The ADuM6132 is an isolated half-bridge gate driver that employs the Analog Devices, Inc., iCoupler® technology to provide an isolated high-side driver with an integrated 275 mW high-side supply. This supply, provided by an internal isolated dc-to-dc converter, powers not only the ADuM6132 high-side output but also any external buffer circuitry that is commonly used with the ADuM6132. This functionality eliminates the cost, space, and performance issues associated with external supply configurations such as a bootstrap circuit.The architecture of the ADuM6132 isolates the high-side channel and the high-side power from the control and low- side interface circuitry. Care has been taken to ensure close matching between the high-side and low-side driver timing characteristics to reduce the need for a dead time margin.In comparison to gate drivers that employ high voltage level translation methodologies, the ADuM6132 offers the benefit of true, galvanic isolation. The differential voltage between high-side and low-side channels can be as high as 800 V with good insulation lifetime (see Table 12).isoPower® uses high frequency switching elements to transfer power through its transformer. Special care must be taken during printed circuit board (PCB) layout to meet emissions standards. Refer to the AN-0971 Application Note for details on board layout considerations.Applications MOSFET/IGBT Gate Drivers Motor Drives Solar Panel Inverters Power Supplies