ANALOGUE SWITCH DUAL SPDT MSOP-10; Analog Switch Type:SPDT; No. of Channels:2Channels; On State Resistance Max:4ohm; Supply Voltage Range:1.8V to 5.5V; Analog Switch Case:MSOP; No. of Pins:10Pins; Operating Temperature Min:-40 C

The ADGS1414D contains eight independent SPST switches. A serial peripheral interface (SPI) controls the switches. The SPI has robust error detection features, such as cyclic redundancy check (CRC) error detection, invalid read and write address detection, and SCLK count error detection. It is possible to daisy-chain multiple ADGS1414D devices together. Daisy-chain mode enables the configuration of multiple devices with a minimal amount of digital lines. The route of digital signals and supplies through the ADGS1414D allows for a further increase in channel density. Integrated passive components eliminate the need for external passive components. FUNCTIONAL BLOCK DIAGRAM Figure 1. The ADGS1414D is suited to high density switching applications, such as large switching matrices and fanout applications. Each switch conducts equally well in both directions when on, and each switch has an input signal range that extends to the supplies. In the off condition, signal levels up to the supplies are blocked. Multifunction pin names may be referenced by their relevant function only.Applications? Automated test equipment Data acquisition systems Sample-and-hold systems Audio and video signal routing Communications systems Relay replacement

The ADG1421 / ADG1422?/ ADG1423?contain two independent single-pole/single-throw (SPST) switches. The ADG1421 and ADG1422 differ only in that the digital control logic is inverted. The ADG1421 switches are turned on with Logic 1 on the appropriate control input, and Logic 0 is required for the ADG1422. The ADG1423 has one switch with digital control logic similar to that of the ADG1421; the logic is inverted on the other switch. The ADG1423 exhibits break-before-make switching action for use in multiplexer applications. Each switch conducts equally well in both directions when on and has an input signal range that extends to the supplies. In the off condition, signal levels up to the supplies are blocked.The iCMOS? (industrial CMOS) modular manufacturing process combines high voltage, complementary metal-oxide semiconductor (CMOS) and bipolar technologies. It enables the development of a wide range of high performance analog ICs capable of 33 V operation in a footprint that no other generation of high voltage parts has achieved. Unlike analog ICs using conventional CMOS processes, iCMOS components can tolerate high supply voltages while providing increased performance, dramatically lower power consumption, and reduced package size.The on resistance profile is very flat over the full analog input range ensuring excellent linearity and low distortion when switching audio signals. The iCMOS construction ensures ultralow power dissipation, making the part ideally suited for portable and battery-powered instruments.PRODUCT HIGHLIGHTS 2.4 ? maximum on resistance at 25?C. Minimum distortion. 3 V logic-compatible digital inputs: VIH = 2.0 V, VIL = 0.8 V. No VL logic power supply required. 10-lead MSOP and 10-lead, 3 mm ? 3 mm LFCSP packages.APPLICATIONS Automatic test equipment Data acquisition systems Relay replacements Battery-powered systems Sample-and-hold systems Audio signal routing Video signal routing Communication systems

The ADG5243F comprises three independently selectable, singlepole/double-throw (SPDT) switches. All channels exhibit break-before-make switching action that prevents momentary shorting when switching channels. An EN input enables or disables the device. When disabled, all channels are switched off. Each switch conducts equally well in both directions when on, and each switch has an input signal range that extends to the supplies. The primary supply voltages define the on-resistance profile, whereas the secondary supply voltages define the voltage level at which the overvoltage protection engages.When no power supplies are present, the channel remains in the off condition, and the switch inputs are high impedance. Undernormal operating conditions, if the analog input signal levels on any Sx pin exceed the positive fault voltage (POSFV) or the negative fault voltage (NEGFV) by a threshold voltage (VT), the channel turns off and that Sx pin becomes high impedance. If the switch is selected to be on, then the drain pin is pulled to the secondary supply voltage that was exceeded. Input signal levels upto ?55 V or +55 V relative to ground are blocked, in both the powered and unpowered conditions.The low capacitance and charge injection of these switches make them ideal solutions for data acquisition and sample-andholdapplications, where low glitch switching and fast settling times are required.Note that, throughout this data sheet, multifunction pins, such as IN1/F1, are referred to either by the entire pin name or by asingle function of the pin, for example, IN1, when only that function is relevant.Product Highlights The source pins are protected against voltages greater than?the secondary supply rails, up to ?55 V and +55 V. The source pins are protected against voltages between??55 V and +55 V in an unpowered state. Overvoltage detection with the digital output indicates the?operating state of the switches. Trench isolation guards against latch-up. Optimized for low charge injection and on-capacitance. The ADG5243F can be operated from a dual supply of ?5 V?to ?22 V or a single power supply of 8 V to 44 V.Applications Analog input/output modules? Process control/distributed control systems? Data acquisition? Instrumentation? Avionics? Automatic test equipment? Communication systems? Relay replacement?

The ADG5248F and ADG5249F are 8:1 and dual 4:1 analog multiplexers. The ADG5248F switches one of eight inputs to a common output and the ADG5249F switches one of four differential inputs to a common differential output. Each channel conducts equally well in both directions when on, and each channel has an input signal range that extends to the supplies. The primary supply voltages define the on-resistance profile, whereas the secondary supply voltages define the voltage level at which the overvoltage protection engages.When no power supplies are present, the channel remains in the off condition, and the switch inputs are high impedance. Under normal operating conditions, if the analog input signal levels on any Sx pin exceed positive fault voltage (POSFV) or negative fault voltage (NEGFV) by a threshold voltage (VT), the channel turns off and that Sx pin becomes high impedance. If the switch is selected to be on, then the drain pin is pulled to the secondary supply voltage that was exceeded. Input signal levels up to +55 V or ?55 V relative to ground are blocked, in both the powered and unpowered condition.The low capacitance and charge injection of these switches make them ideal solutions for data acquisition and sample-and-hold applications, where low glitch switching and fast settling times are required.?Note that, throughout this data sheet, multifunction pins, such as A0/F2, are referred to either by the entire pin name or by a single function of the pin, for example, A0, when only that function is relevant.?Product Highlights Source pins are protected against voltages greater than the secondary supply rails, up to ?55 V and +55 V. Source pins are protected against voltages between ?55 V and +55 V in an unpowered state. Overvoltage detection with digital output indicates operating state of switches. Trench isolation guards against latch-up. Optimized for low charge injection and on-capacitance. The ADG5248F/ADG5249F can be operated from a dual?supply of ?5 V to ?22 V or a single power supply of 8 V to 44 V.Applications Analog input/output modules Process control/distributed control systems Data acquisition Instrumentation Avionics Automatic test equipment Communication systems Relay replacement

The ADG854 is a low voltage CMOS device containing two independently selectable single-pole, double-throw (SPDT) switches. This device offers ultralow on resistance of less than 0.8 ? over the full temperature range. The ADG854 is fully specified for 5.5 V, 3.3 V, and 2.5 V supply operation. Each switch conducts equally well in both directions when on, and has an input signal range that extends to the supplies. The ADG854 exhibits break-before-make switching action. The ADG854 is available in a 1.6 mm ? 1.3 mm 10-lead mini LFCSP package.Applications Cellular phones PDAs MP3 players Power routing Battery-powered systems PCMCIA cards Modems Audio and video signal routing Communication systems

The ADGS1412 contains four independent single-pole/single-throw(SPST) switches. A serial peripheral interface (SPI)controls the switches. The SPI interface has robust error detectionfeatures such as cyclic redundancy check (CRC) error detection,invalid read/write address detection, and SCLK count errordetection.It is possible to daisy-chain multiple ADGS1412 devices together.Daisy-chain mode enables the configuration of multiple deviceswith a minimal amount of digital lines. The ADGS1412 can alsooperate in burst mode to decrease the time between SPIcommands.iCMOS construction ensures ultralow power dissipation, makingthe device ideally suited for portable and battery-poweredinstruments.Each switch conducts equally well in both directions when on,and each switch has an input signal range that extends to thesupplies. In the off condition, signal levels up to the suppliesare blocked.The on-resistance profile is flat over the full analog input range,which ensures good linearity and low distortion when switchingaudio signals.Product Highlights SPI interface removes the need for parallel conversion, logic traces and reduces general-purpose input/output (GPIO) channel count. Daisy-chain mode removes additional logic traces when multiple devices are used. CRC error detection, invalid read/write address detection, and SCLK count error detection ensures a robust digital interface. CRC and error detection capabilities allow the use of the ADGS1412 in safety critical systems. Guaranteed break-before-make switching allows the use of the ADGS1412 in multiplexer configurations with external wiring. Minimum distortion.Applications Automated test equipment Data acquisition systems Battery-powered systems Sample-and-hold systems Audio signal routing Video signal routing Communications systems Relay replacement

The ADN4605 is a 40 ? 40 asynchronous, protocol agnostic,?digital crosspoint switch, with 40 differential PECL/CML-compatible inputs and 40 differential programmable CML outputs.The ADN4605 is optimized for NRZ signaling with data rates of up to 4.25 Gbps per port. Each port offers adjustable levels of input equalization, programmable output swing, and output preemphasis/deemphasis.The ADN4605 nonblocking switch core implements a 40 ? 40?crossbar and supports independent channel switching through serial and parallel control interfaces. The ADN4605 has low?latency and very low channel-to-channel skew.An I2C, SPI, or parallel interface is used to communicate with the device for control of connectivity and other features.The ADN4605 is assembled in a 35 mm ? 35 mm, 352 BGA?package and operates over a temperature range of ?40?C to +85?C.APPLICATIONS Digital video (HDMI, DVI, DisplayPort, 3G/HD/SD-SDI) Fiber optic network switching High-speed serial backplane routing to OC-48 with FEC XAUI, 4x Fibre Channel, Infiniband?, and GbE over backplane Data storage networks

The ADRF5301 is a reflective, single-pole, double-throw (SPDT) switch manufactured in the silicon process.The ADRF5301 was developed for 5G applications from 35 GHz to 44 GHz. This device has low insertion loss of 1.8 dB, high isolation of 28 dB, and radio frequency (RF) input power handling capability of 28 dBm average and 36 dBm peak.The ADRF5301 incorporates a negative voltage generator (NVG) to operate with a single positive supply of 3.3 V applied to the VDD pin. The devices employs complementary metal-oxide semiconductor (CMOS)-/low voltage transistor to transistor logic (LVTTL)-compatible control.The ADRF5301 is pin-compatible with the ADRF5300, which operates from 24 GHz to 32 GHz.The ADRF5301 comes in a 20-terminal, 3 mm ? 3 mm, RoHS-compliant, land grid array (LGA) package and can operate from ?40?C to +105?C.Applications Industrial scanner Test instrumentation Cellular infrastructure mmWave 5G Military radios, radars, electronic counter measures (ECMs) Microwave radios and very small aperture terminals (VSATs) ?

The AD8153 is an asynchronous, protocol agnostic, single-lane 2:1 switch with three differential CML inputs and three differential CML outputs. The AD8159, another member of the Xstream line of products, is suitable for similar applications that require more than one lane.The AD8153 is optimized for NRZ signaling with data rates of up to 3.2 Gbps per port. Each port offers two levels of input equalization and four levels of output pre-emphasis.The device consists of a 2:1 multiplexer and a 1:2 demultiplexer. There are three operating modes: pin mode, serial mode, and mixed mode. In pin mode, lane switching, equalization, and pre-emphasis are controlled exclusively using external pins. In serial mode, an I2C interface is used to control the device and to provide access to advanced features, such as additional pre- emphasis settings and output disable. In mixed mode, the user accesses the advanced features using I2C, but controls lane switching using the external pins.The main application of the AD8153 is to support redundancy on both the backplane side and the line interface side of a serial link. The device has unicast and bicast capability, so it is capable of supporting either 1 + 1 or 1:1 redundancy.Using a mixture of bicast and loopback modes, the AD8153 can also be used to test high speed serial links by duplicating the incoming data and transmitting it to the destination port and test equipment simultaneously.APPLICATIONS Low cost redundancy switch SONET OC48/SDH16 and lower data rates Gigabit Ethernet over backplane Fibre Channel 1.06 Gbps and 2.12 Gbps over backplane Serial RapidIO PCI Express Gen 1 Infiniband over backplane