The HMC7992 is a general-purpose, nonreflective, 0.1 GHz to 6.0 GHz, silicon, single-pole, four-throw (SP4T) switch in aleadless, surface-mount package. The switch is ideal for cellular infrastructure applications, offers high isolation of 45 dB typical at 2 GHz, and a low insertion loss of 0.6 dB at 2 GHz. It offers excellent power handling capability up to 6.0 GHz, with inputpower of 1 dB compression point (P1dB) of 35 dBm at 5 V operation. The HMC7992 has good low frequency input power handling below 0.1 GHz and can operate well down to 10 kHz, with a typical 1 dB compression of 21 dBm and an IIP3 of 37 dBm at 1 MHz.The on-chip circuitry allows the HMC7992 to operate at a single, positive supply voltage range from 3.3 V to 5 V, and as well as a single, positive control voltage from 0 V to 1.8 V/3.3 V/5.0 V. A 2:4 decoder integrated in the switch requires only two controlled input signals, with a positive control voltage range from 0 V to 1.8 V/3.3 V/5.0 V, to select one of the four radio frequency (RF)paths.Applications Cellular/4G infrastructure Wireless infrastructure Automotive telematics Mobile radios Test equipment

The DG201A and DG211 are normally closed, quadsingle-pole single-throw (SPST) analog switches. TheseCMOS switches can be continuously operated withpower supplies ranging from ±4.5V to ±18V. Maximguarantees that these switches will not latch up if thepower supplies are disconnected with input signals stillconnected.Both devices have guaranteed break-before-makeswitching. The DG201A differs from the DG211 primarilyin switching speeds. The DG201A has a maximumturn-off time of 450ns and a maximum turn-on time of600ns. The DG211 has a maximum turn-off time of500ns and a maximum turn-on time of 1000ns.Compared to the original manufacturer's products,Maxim's DG201A and DG211 consume significantlylower power making them better suited for portableapplications. Maxim has also eliminated the need forthe third (VL) power supply that is required for the operationof the original manufacturer's DG211.ApplicationsCommunication SystemsGuidance and Control SystemsHeads-Up DisplaysMilitary RadiosPBX, PABXTest EquipmentWinchester Disk Drives

The ADG858 is a low voltage CMOS device containing foursingle-pole, double-throw (SPDT) switches. This device offersultralow on resistance of less than 0.82 Ω over the full temperaturerange. The ADG858 is fully specified for 4.2 V to 5.5 V and 2.7 Vto 3.6 V supply operation.Each switch conducts equally well in both directions when onand has an input signal range that extends to the supplies. TheADG858 exhibits break-before-make switching action.The ADG858 is available in a 2.1 mm × 2.1 mm, 16-lead miniLFCSP. This tiny package makes the device ideal for spaceconstrainedapplications, such as handsets, PDAs, and MP3s.Product Highlights <0.82 Ω over the full temperature range of −40°C to +85°C. Single 1.8 V to 5.5 V operation. Compatible with 1.8 V CMOS logic. High current handling capability (250 mA continuous current per channel). Low THD + N: 0.06% typical. 2.1 mm × 2.1 mm, 16-lead mini LFCSP.Applications Cellular phones PDAs MP3 players Power routing Battery-powered systems PCMCIA cards Modems Audio and video signal routing Communication systems

The ADG1414 is a monolithic complementary metal oxide semiconductor (CMOS) device containing eight independently selectable switches designed on an industrial CMOS (iCMOS®) process. iCMOS is a modular manufacturing process combining high voltage CMOS and bipolar technologies. iCMOS components can tolerate high supply voltages while providing increased performance, dramatically lower power consumption, and reduce the package size.The ADG1414 is a set of octal SPST (single-pole, single-throw) switches controlled via a 3-wire serial interface. On resistance is closely matched between switches and is very flat over the full signal range. Each switch conducts equally well in both directions and the input signal range extends to the supplies.Data is written to these devices in the form of eight bits; each bit corresponds to one channel.The ADG1414 utilizes a versatile 3-wire serial interface that operates at clock rates of up to 50 MHz and is compatible with standard SPI®, QSPI™, MICROWIRE™, and DSP interface standards. The output of the shift register, SDO, enables a number of these parts to be daisy chained.On power-up, all switches are in the off condition, and the internal registers contain all zeros.PRODUCT HIGHLIGHTS 50 MHz serial interface. 9.5 Ω on resistance. 1.6 Ω on-resistance flatness. 24-lead TSSOP and 4 mm × 4 mm LFCSP packages.APPLICATIONS Automatic test equipment Data acquisition systems Battery-powered systems Sample-and-hold systems Audio signal routing Video signal routing Communication systems

The ADG1606 and ADG1607 are monolithic iCMOS® analogmultiplexers comprising of 16 single channels and eightdifferential channels, respectively. The ADG1606 switches one of16 inputs to a common output, as determined by the 4-bitbinary address lines (A0, A1, A2, and A3). The ADG1607switches one of eight differential inputs to a common differentialoutput, as determined by the 3-bit binary address lines (A0, A1,and A2). An EN input on both devices enables or disables thedevice. When disabled, all channels switch off. When enabled,each channel conducts equally well in both directions and has aninput signal range that extends to the supplies.The ultralow on resistance and on-resistance flatness of theseswitches make them ideal solutions for data acquisition andgain switching applications where low distortion is critical.iCMOS® construction ensures ultralow power dissipation,making the parts ideally suited for portable and battery-poweredinstruments.Product Highlights 7.5 Ω maximum on resistance over temperature. Minimum distortion: THD + N = 0.04% 3 V logic-compatible digital inputs: VINH = 2.0 V, VINL = 0.8 V. No VL logic power supply required.Applications Communication systems Medical systems Audio signal routing Video signal routing Automatic test equipment Data acquisition systems Battery-powered systems Sample-and-hold systems Relay replacements

The ADG1636 is a monolithic CMOS device containing twoindependently selectable single-pole/double-throw (SPDT)switches. An EN input is used to enable or disable the device.When disabled, all channels are switched off. Each switch conductsequally well in both directions when on and has an input signalrange that extends to the supplies. In the off condition, signallevels up to the supplies are blocked. Both switches exhibitbreak-before-make switching action for use in multiplexerapplications.The ultralow on resistance of these switches make them idealsolutions for data acquisition and gain switching applications wherelow on resistance and distortion is critical. The on resistance profileis very flat over the full analog input range, ensuring excellentlinearity and low distortion when switching audio signals.The CMOS construction ensures ultralow power dissipation,making the devices ideally suited for portable and battery-poweredinstruments.Product Highlights 1.6 Ω maximum on resistance over temperature. Minimum distortion: THD + N = 0.007%. 3 V logic-compatible digital inputs: VINH = 2.0 V, VINL = 0.8 V. No VL logic power supply required. Ultralow power dissipation: <16 nW. 16-lead TSSOP and 16-lead 4 mm × 4 mm LFCSP.Applications Communication systems Medical systems Audio signal routing Video signal routing Automatic test equipment Data acquisition systems Battery-powered systems Sample-and-hold systems Relay replacements

The ADG4612 & ADG4613 contain four independent single-pole/single-throw (SPST) switches. The ADG4612 switches areturned on with Logic 1 on the appropriate control input. TheADG4613 has two switches with digital control logic similar tothat of the ADG4612; the logic is inverted on the other twoswitches. Each switch conducts equally well in both directionswhen on and has an input signal range that extends to thesupplies. The ADG4613 exhibits break-before-make switchingaction for use in multiplexer applications.When no power supplies are present the switch remains in theOFF condition and the switch inputs are high impedanceinputs. This ensures that no current flows that may damage theswitch. This is very useful in application where analog signalsmay be present at the switch inputs before power or where theuser has no control over the Power Supply Sequence.In the off condition, signal levels up to 16V are blocked. Also, ifthe analog input signal levels exceed VDD by VT then the switchwill turn off.The ultralow on resistance of these switches make them idealsolutions for data acquisition and gain switching applicationswhere low on resistance and distortion is critical. The onresistance profile is very flat over the full analog input rangeensuring excellent linearity and low distortion when switchingaudio signals.APPLICATIONS Hot swap applications Data acquisition systems Battery-powered systems Automatic test equipment Communication systems Relay ReplacementPRODUCT HIGHLIGHTS Power-Off Protection On Both S and D Pins. PSS Robustness. Overvoltage Protection up to 16 V. 5.2 Ω On Resistance. 16-Lead TSSOP and 3 mm × 3 mm LFCSP Packages.

The ADG4612 & ADG4613 contain four independent single-pole/single-throw (SPST) switches. The ADG4612 switches areturned on with Logic 1 on the appropriate control input. TheADG4613 has two switches with digital control logic similar tothat of the ADG4612; the logic is inverted on the other twoswitches. Each switch conducts equally well in both directionswhen on and has an input signal range that extends to thesupplies. The ADG4613 exhibits break-before-make switchingaction for use in multiplexer applications.When no power supplies are present the switch remains in theOFF condition and the switch inputs are high impedanceinputs. This ensures that no current flows that may damage theswitch. This is very useful in application where analog signalsmay be present at the switch inputs before power or where theuser has no control over the Power Supply Sequence.In the off condition, signal levels up to 16V are blocked. Also, ifthe analog input signal levels exceed VDD by VT then the switchwill turn off.The ultralow on resistance of these switches make them idealsolutions for data acquisition and gain switching applicationswhere low on resistance and distortion is critical. The onresistance profile is very flat over the full analog input rangeensuring excellent linearity and low distortion when switchingaudio signals.APPLICATIONS Hot swap applications Data acquisition systems Battery-powered systems Automatic test equipment Communication systems Relay ReplacementPRODUCT HIGHLIGHTS Power-Off Protection On Both S and D Pins. PSS Robustness. Overvoltage Protection up to 16 V. 5.2 Ω On Resistance. 16-Lead TSSOP and 3 mm × 3 mm LFCSP Packages.

The ADG5408/ADG5409 are monolithic CMOS analog multiplexerscomprising eight single channels and four differentialchannels, respectively. The ADG5408 switches one of eightinputs to a common output, as determined by the 3-bit binaryaddress lines, A0, A1, and A2. The ADG5409 switches one offour differential inputs to a common differential output, asdetermined by the 2-bit binary address lines, A0 and A1.An EN input on both devices enables or disables the device.When EN is disabled, all channels are switched off. The on-resistanceprofile is very flat over the full analog input range, whichensures good linearity and low distortion when switching audiosignals. High switching speed also makes the parts suitable forvideo signal switching.Each switch conducts equally well in both directions when on,and each switch has an input signal range that extends to the powersupplies. In the off condition, signal levels up to the suppliesare blocked.The ADG5408/ADG5409 do not have a VL pins; rather, the logic powersupply is generated internally by an on-chip voltage generator.Product Highlights  Trench isolation guards against latch-up. A dielectric trench separates the P and N channel transistors thereby preventing latch-up even under severe overvoltage conditions.  Low RON.  Dual-supply operation. For applications where the analog signal is bipolar, the ADG5408/ADG5409 can be operated from dual supplies up to ±22 V.  Single-supply operation. For applications where the analog signal is bipolar, the ADG5408/ADG5409 can be operated from a single-rail power supply up to 40V.  3 V logic-compatible digital inputs: VINH = 2.0 V, VINL = 0.8 V.  No VL logic power supply required.Applications Relay replacement  Automatic test equipment  Data acquisition  Instrumentation  Avionics Audio and video switching  Communication systems 

The ADG5408/ADG5409 are monolithic CMOS analog multiplexerscomprising eight single channels and four differentialchannels, respectively. The ADG5408 switches one of eightinputs to a common output, as determined by the 3-bit binaryaddress lines, A0, A1, and A2. The ADG5409 switches one offour differential inputs to a common differential output, asdetermined by the 2-bit binary address lines, A0 and A1.An EN input on both devices enables or disables the device.When EN is disabled, all channels are switched off. The on-resistanceprofile is very flat over the full analog input range, whichensures good linearity and low distortion when switching audiosignals. High switching speed also makes the parts suitable forvideo signal switching.Each switch conducts equally well in both directions when on,and each switch has an input signal range that extends to the powersupplies. In the off condition, signal levels up to the suppliesare blocked.The ADG5408/ADG5409 do not have a VL pins; rather, the logic powersupply is generated internally by an on-chip voltage generator.Product Highlights  Trench isolation guards against latch-up. A dielectric trench separates the P and N channel transistors thereby preventing latch-up even under severe overvoltage conditions.  Low RON.  Dual-supply operation. For applications where the analog signal is bipolar, the ADG5408/ADG5409 can be operated from dual supplies up to ±22 V.  Single-supply operation. For applications where the analog signal is bipolar, the ADG5408/ADG5409 can be operated from a single-rail power supply up to 40V.  3 V logic-compatible digital inputs: VINH = 2.0 V, VINL = 0.8 V.  No VL logic power supply required.Applications Relay replacement  Automatic test equipment  Data acquisition  Instrumentation  Avionics Audio and video switching  Communication systems